SINAMICS G120 Smart Access SINAMICS SINAMICS G120 Smart Access Operating Instructions 06/2019 A5E43332487-003 Preface Fundamental safety instructions 1 Product overview 2 Installing 3 Accessing the Web pages 4 Standard Web pages 5 Upgrading 6 Additional information 7
Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.
Preface Product maintenance The components are subject to continuous further development within the scope of product maintenance (improvements to robustness, discontinuations of components, etc). These further developments are "spare parts-compatible" and do not change the article number. In the scope of such spare parts-compatible further developments, connector positions are sometimes changed slightly. This does not cause any problems with proper use of the components.
Table of contents Preface ................................................................................................................................................... 3 1 2 Fundamental safety instructions .............................................................................................................. 6 1.1 General safety instructions ...................................................................................................... 6 1.
Table of contents 5.9 Diagnostics .............................................................................................................................59 5.10 5.10.1 5.10.2 5.10.3 5.10.4 Backup and restore .................................................................................................................62 Backing up ..............................................................................................................................62 Restoring ............................
1 Fundamental safety instructions 1.1 General safety instructions WARNING Danger to life if the safety instructions and residual risks are not observed If the safety instructions and residual risks in the associated hardware documentation are not observed, accidents involving severe injuries or death can occur. • Observe the safety instructions given in the hardware documentation. • Consider the residual risks for the risk evaluation.
Fundamental safety instructions 1.3 Industrial security 1.3 Industrial security Note Industrial security Siemens provides products and solutions with industrial security functions that support the secure operation of plants, systems, machines and networks. In order to protect plants, systems, machines and networks against cyber threats, it is necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial security concept.
Product overview 2 Product overview 2.1 Introduction The SINAMICS G120 Smart Access is a Wi-Fi based Web server module and an engineering tool. It has been designed for quick setup, parameterization, and diagnostics of the supported SINAMICS G120 converters.
Product overview 2.1 Introduction System requirements Device with wireless network adapter installed Operating system Recommended Web browser 1) PC Windows 7 • Google Chrome version 64.0.3239 or later • IE version 11.0.9600 or later • Firefox version 50.0.2 or later • Google Chrome version 65.0 or later • Edge version 38.14393.1066 or later • Firefox version 50.0.2 or later • Google Chrome version 65.0 or later • Firefox version 10.6 or later • Safari • Google Chrome version 64.0.
Product overview 2.2 Layout and functions 2.2 Layout and functions Layout Button functions Button Function Reset • Holding down the button for more than three seconds when the SINAMICS G120 Smart Access is in power-on state resets the Wi-Fi configuration of the SINAMICS G120 Smart Access to factory defaults. • Holding down the button when the SINAMICS G120 Smart Access is in power-off state and powering on the module enters basic upgrading mode.
Product overview 2.3 Scope of delivery 2.
Product overview 2.4 Device disposal Serial number explanation (example) 2.4 Device disposal Recycling and disposal For environmentally-friendly recycling and disposal of your old device, please contact a company certified for the disposal of waste electrical and electronic equipment, and dispose of the old device as prescribed in the respective country of use.
3 Installing Note SINAMICS G120 Smart Access power supply The SINAMICS G120 Smart Access has no internal power supply and derives its power directly from the converter through the RS232 interface. Any configuration data stored on the SINAMICS G120 Smart Access is saved to its memory which does not require power to retain the data.
Installing Fitting the SINAMICS G120 Smart Access to the converter Note Before fitting the SINAMICS G120 Smart Access to the converter, make sure that the converter has been installed correctly, in accordance with relevant requirements in the Operating Instructions. Note SINAMICS G120 Smart Access is suitable for cabinet installation. To ensure good signal transmission, make sure that you leave the cabinet door open when the module is operational.
Accessing the Web pages 4 You can access the SINAMICS G120 Web pages from a PC or a mobile device that connects to the SINAMICS G120 Smart Access. 4.1 Establishing the wireless network connection NOTICE Equipment malfunctions as a result of unauthorized access to the converter Hacker attack can result in unauthorized access to the converter through the SINAMICS G120 Smart Access. This can cause equipment malfunctions.
Accessing the Web pages 4.1 Establishing the wireless network connection 5. Enter the SINAMICS G120 Web site (http://192.168.1.1 or https://192.168.1.1) in the supported browser. Note After the establishment of the wireless network connection for the first time, it may take some time for the Web browser to open the SINAMICS G120 Web page.
Accessing the Web pages 4.1 Establishing the wireless network connection Note that this password change page includes a security level indicator. The indicator uses different colors to indicate the security strength of your current password. For detailed information, see the table below: Password security level Description Low The password includes 8 or 9 characters and is a mixture of numbers, uppercase and lowercase letters.
Accessing the Web pages 4.1 Establishing the wireless network connection Installing SSL certificates (only for access with https://) To access the SINAMICS G120 Web pages with https:// from a Windows 10-based PC or iOS-based mobile devices, you need to install SSL certificates. Installing on Windows 10-based PCs 1. Enter the certificate download Web site (https://support.industry.siemens.com/cs/ww/en/ps/13225/dl) and download "G120 smart access certificates.zip". Extract the certificate file "root-ca-cert.
Accessing the Web pages 4.1 Establishing the wireless network connection 3. Select "Settings > General > Profiles" to view configuration profiles in your mobile device and make sure that the certificate has been issued to "G120 Smart Access 2018". 4. Select "Settings > General > About > Certificate Trust Settings" to enable full trust for the root certificate "G120 Smart Access 2018". Now you are able to access the SINAMICS G120 Web pages via the SINAMICS G120 Smart Access.
Accessing the Web pages 4.2 Accessing the Web pages Wireless network connection examples Precondition: Your mobile device must be wireless-enabled. For Windows 7/Windows 10 (on PCs) For Android and iOS (on tablets/smart phones) 1. Click Go to the Wi-Fi setting window on your tablet or smart phone, select the target network, and then enter the wireless password to launch the connection. on the taskbar on your PC. 2. Select the target network and enter the wireless password to launch the connection.
5 Standard Web pages 5.1 Home page 5.1.
Standard Web pages 5.2 Optional settings page 5.1.2 Viewing connection status You can view the connection status in the upper-left corner of the Web pages. Icon Status Connected Description Communication between the PC/mobile device and the converter is established.
Standard Web pages 5.2 Optional settings page 5.2.1 Configuring Wi-Fi If you do not want to use the factory default Wi-Fi settings, you can change Wi-Fi configuration in the following dialog box: The new Wi-Fi configuration takes effect only after the SINAMICS G120 Smart Access is restarted.
Standard Web pages 5.2 Optional settings page Signal strength Default signal strength: 0 (strong) The wireless network signal transmission distance may vary with environmental conditions. When selecting the desired signal strength, consider both the acceptable signal transmission distance and the corresponding wireless network security. You can select a desired strength with the slider.
Standard Web pages 5.2 Optional settings page 5.2.2 Changing the display language The SINAMICS G120 Web pages support the following user interface languages: English (default), Chinese, German, Italian, Spanish, and French.
Standard Web pages 5.2 Optional settings page 5.2.3 Synchronizing the time When the connection between the converter and the PC/mobile device is established, the Web page can display the current time and date information of the connected PC/mobile device (see below). You can enable time synchronization between the converter and the connected PC/mobile device to record the occurrence time of converter faults/alarms.
Standard Web pages 5.2 Optional settings page 5.2.
Standard Web pages 5.2 Optional settings page 5.2.6 Configuring communication protocol The SINAMICS G120 Web pages support two communication protocols: http (enabled by default) and https. To access the Web pages by using the "https" protocol only, proceed as follows: Note Installing SSL certificates To access the SINAMICS G120 Web pages with https:// from a Windows 10-based PC or iOS-based mobile devices, you must install SSL certificates.
Standard Web pages 5.2 Optional settings page 5.2.7 Restarting the SINAMICS G120 Smart Access You can use this function to restart the SINAMICS G120 Smart Access. After the SINAMICS G120 Smart Access is restarted, reconnect your PC/mobile device to the module and refresh the Web application.
Standard Web pages 5.2 Optional settings page 5.2.8 Selecting quick setup mode (G120X/G120XA converters only) This option is visible only when your SINAMICS G120 Smart Access is connected to G120X/G120XA converter.
Standard Web pages 5.3 Converter identification 5.3 Converter identification The converter identification Web page displays detailed information of the currently connected converter: Note For G120X and G120XA converters, the converter identification Web page will not display the Control Unit article number and the Control Unit serial number. Note For G120C converters, the converter identification Web page will not display information about Power Module.
Standard Web pages 5.4 Classic quick setup 5.4 Classic quick setup The classic quick setup is applicable to all the converters supported by SINAMICS G120 Smart Access. For G120X/G120XA converters, it is recommended to use the setup mode (Page 38) which is specific for the G120X/G120XA converters.
Standard Web pages 5.4 Classic quick setup Operating sequence 1. Open the classic quick setup Web page by selecting the quick setup icon from either the home page or the navigation sidebar. Note For G120X/G120XA converters, if you want to use this quick setup mode, you must select "classic quick setup (Page 30)" first. 2. Reset to factory settings (recommended) or modify existing settings. 3. Select an application class according to the particular converter connected.
Standard Web pages 5.4 Classic quick setup 4. Set the required motor data. For Siemens motors, enter only the motor data as shown in ④ and the SINAMICS G120 Smart Access will automatically identify the rest of the motor data. 5. Select the factory interface settings for the converter based on your particular application. Note that the factory interface settings vary depending on the connected converter.
Standard Web pages 5.4 Classic quick setup 6. Set the following parameters based on your particular application. – Minimum speed - factory setting 0 [rpm] The minimum speed is the lowest speed of the motor independent of the speed setpoint. – Maximum speed - factory setting 1500 [rpm] The converter limits the motor speed to the maximum speed. – The ramp-up and ramp-down times define the maximum motor acceleration when the speed setpoint changes.
Standard Web pages 5.4 Classic quick setup 7. Select the desired technological application. Depending on the selected application class, the available technological applications may vary.
Standard Web pages 5.5 Setup (G120X/G120XA converters only) 8. Select the method which the converter uses to measure the data of the connected motor.
Standard Web pages 5.5 Setup (G120X/G120XA converters only) 5.5 Setup (G120X/G120XA converters only) The setup Web page allows you to configure a more comprehensive range of settings to meet the specific requirements of the G120X/G120XA converters.
Standard Web pages 5.5 Setup (G120X/G120XA converters only) Expanded page for quick setup When you see the Expand symbol on the top right of the quick setup page, click the symbol and an expanded quick setup page opens. You can do the following on this page: ● View the status of individual quick setup steps based on the symbols given below: Completed step Current step To-be-completed step ● Go back to a completed step.
Standard Web pages 5.5 Setup (G120X/G120XA converters only) Operating sequence 1. Open the setup Web page by selecting the setup icon from either the home page or the navigation sidebar. 2. Open the quick setup Web page by selecting the quick setup icon. 3. Start a new configuration (recommended) or modify the existing configuration. – If you select to start a new configuration, factory reset is performed automatically.
Standard Web pages 5.5 Setup (G120X/G120XA converters only) 4. If you have selected to start a new configuration, select an application according to the particular converter connected. If PID control is selected, factory interface settings that are relevant to PID control will be displayed in the I/O configuration Web page. 5. Set the required motor data. For Siemens motors, enter only the motor data as shown in ⑥ and the SINAMICS G120 Smart Access will automatically identify the rest of the motor data.
Standard Web pages 5.5 Setup (G120X/G120XA converters only) 6. Select the factory interface settings for the converter based on your particular application. Note that the factory interface settings vary depending on the connected converter.
Standard Web pages 5.5 Setup (G120X/G120XA converters only) Edit the selected factory interface settings, if desired. You can do the following on the editing page: – Add AI/DI function – Edit AI/DI function – Edit AI scaling – Change fieldbus settings Note that in the editing page, the numbers below the DI, AI, or Fieldbus refer to terminals on the Control Unit. I/O terminals marked with superscript "ext" represent the terminals on the I/O Extension Module.
Standard Web pages 5.5 Setup (G120X/G120XA converters only) 7. Set the following parameters based on your particular application. Note that the available parameters vary depending on the connected converter. Limit settings Minimum frequency P1080 Maximum frequency P1082 Ramp-up time P1120 Ramp-down time P1121 OFF3 ramp-down time P1135 Current limit P0640 Internal setpoint (0...n) P2201...
Standard Web pages 5.5 Setup (G120X/G120XA converters only) 8. Select the method which the converter uses to measure the data of the connected motor. Depending on the configuration type and selected application, the available methods for motor identification may vary: – Inhibited: p1900 = 0 – Motor data identification and speed controller optimization: p1900 = 1 – Motor identification at standstill: p1900 = 2 If you choose to identify the motor data, go to the JOG page after you have finished quick setup.
Standard Web pages 5.5 Setup (G120X/G120XA converters only) 5.5.2 Application setup The application setup Web page allows you to set applications for the G120X/G120XA converter. Operating sequence 1. Open the setup Web page by selecting the quick setup icon from either the home page or the navigation sidebar. 2. Open the application setup Web page by selecting the application setup icon. 3. Set the desired application as the example shown below. If necessary, repeat this step to set other applications.
Standard Web pages 5.6 Parameters 5.6 Parameters You can open the parameters Web page by selecting the parameters icon from either the home page or the navigation sidebar. ① ② ③ Searching parameters Filtering parameters by group Editing "My parameters" ④ ⑤ ⑥ Modifying parameters Resetting parameters Saving parameters After successfully modifying parameters, a red point appears on ⑥ reminding you to save the changed parameters to non-volatile memory.
Standard Web pages 5.6 Parameters Modifying parameters The figure below shows different methods for modifying parameters. Note that when modifying a BICO parameter (example: P0771[0]), you can use the on-screen numeric keypad or your native keyboard to quickly navigate to the parameter values that start with the number(s) you enter.
Standard Web pages 5.6 Parameters Searching parameters You can search parameters by entering parameter ID. If you do not enter any parameter ID and then select the Go icon, the page shows the list of all parameters visible on the Web page. Filtering parameters You can view and set parameters in the target parameter group.
Standard Web pages 5.6 Parameters Editing "My parameters" You can edit the parameters under "My parameters", such as adding, deleting, importing and exporting. Three groups are available under "My parameters" and the numbers on the right indicate the number of the parameters in each group.
Standard Web pages 5.6 Parameters All successfully saved parameters will go to the corresponding parameter group. Proceed as follows to view these parameters: If desired, you can also import or export "My parameters" (recommended on PC). Continue as follows: Note Precondition You have navigated to the desired parameter group under "My parameters" shown as the image above. The softkeys "Import" and "Export" are not available if you are under the state of "Editing my parameters".
Standard Web pages 5.6 Parameters ● Importing "My parameters" The importing process completes when the following window appears. Note that the imported parameters will overwrite the old parameters in your specified parameter group.
Standard Web pages 5.6 Parameters ● Exporting "My parameters" The exporting process completes with a .xml file saved under your specified path. You can open the file to view the exported parameters. Note that the exported .xml file only shows the parameter numbers. The corresponding parameter values are not shown. Resetting parameters You can select to reset all parameters to either user default settings or factory settings.
Standard Web pages 5.6 Parameters Saving parameters to non-volatile memory You can select to save all parameter settings to the non-volatile memory as either standard parameter set or user default settings.
Standard Web pages 5.7 JOG 5.7 JOG You use this Web page to start the motor test run in JOG or HAND mode. Operating sequence 1. Open the JOG Web page by selecting the JOG icon from either the home page or the navigation sidebar. 2. Proceed as follows to get control of the motor. 3. Identify the motor data. This step varies depending on the setting of the parameter p1900 in quick setup page or in parameter page. • p1900 = 0: Do not measure the motor data.
Standard Web pages 5.
Standard Web pages 5.7 JOG 4. Run the motor in JOG or HAND mode (default mode: JOG). Note that if desired, you can also test the motor rotation direction with the corresponding button ("①"). The page shows the currently selected rotation direction ("②").
Standard Web pages 5.7 JOG 5. After you finish the motor test run, proceed as follows to return the control of the motor: Before returning the control, make sure that there is no converter output and the motor has stopped. If the motor is still running, the following message appears: Note If the Wi-Fi connection is lost during motor test run, you must re-establish the wireless network connection.
Standard Web pages 5.8 Monitoring 5.8 Monitoring You can open the converter status monitoring Web page by selecting the monitoring icon from either the home page or the navigation sidebar. 5.9 Diagnostics You can open the diagnostics Web page by selecting the diagnostics icon from either the home page or the navigation sidebar.
Standard Web pages 5.9 Diagnostics Faults/Alarms On this subpage, you can view the detailed fault/alarm information, acknowledge all faults, or send all faults by e-mail (recommended on PC). Note that when sending faults by email, make sure that your mobile device is connected to the internet. You can use the filter button to display all faults and alarms or the active ones only.
Standard Web pages 5.9 Diagnostics I/O status This subpage displays the detailed I/O status information. Parameters Parameter Function r0722.0...n CO/BO: CU digital input status r0747.0...n CO/BO: CU digital output status r0752[0...n] Actual analog input value [V] or [mA] r0774[0...n] Actual analog output value [V] or [mA] P0756[0...n] Type of analog input P0776[0...
Standard Web pages 5.10 Backup and restore Status bit This subpage displays the detailed status bit information. Parameters Parameter Function r0052.0...15 CO / BO: Active status word 1 r0053.0...11 CO / BO: Active status word 2 5.10 Backup and restore 5.10.1 Backing up You can use the backup Web page to back up parameters to SINAMICS G120 Smart Access and download the backup file (*.bin file) to your local drive (recommended on PC).
Standard Web pages 5.10 Backup and restore Operating sequence 1. Proceed as follows to back up the parameter file to SINAMICS G120 Smart Access. Character restrictions for the file name: maximum 30 characters which are limited to AZ, a-z, 0-9, _, -, (, ), dot, or space. If the name for the new backup file already exists, a message prompts asking you whether you want to overwrite the existing file or cancel the backup process. 2. The backup process completes when the following window appears.
Standard Web pages 5.10 Backup and restore Note Backup files must be protected against unauthorized operation, e.g. by implementing access control. Note When transferring important files (e.g. backup files and/or upgrade files) through email, email must be encrypted or signed. 5.10.2 Restoring You can use the restore Web page to upload, download, delete, and/or restore the selected file (*.bin file). Note The restoring process restores all parameters of access levels up to 3.
Standard Web pages 5.
Standard Web pages 5.10 Backup and restore Restoring the selected file 1. Proceed as follows to start restoring process. 2. The restoring process completes when the following window appears. If the Web page indicates that the restoring fails, you can select to restore again. If required, proceed as follows to save the parameter settings to the non-volatile memory: Note Make sure that the selected file for restoring is specific to the connected converter.
Standard Web pages 5.10 Backup and restore 5.10.3 Saving as XML You can use the saving Web page to save the parameters as XML and download the XML file to your local drive so that you can open and see the parameters. Note The saving process saves all parameters of access levels up to 3 and allows you to save a maximum of 20 files to SINAMICS G120 Smart Access. In case of any further saving attempt, a message appears prompting you to delete some of the existing XML files. Generating an XML file 1.
Standard Web pages 5.
Standard Web pages 5.10 Backup and restore 5.10.4 Transferring You can open the transfer Web page by selecting the backup&restore icon from either the home page or the navigation sidebar. Precondition The SD card file transfer function is available only when a required SD card is inserted into the converter. Before data transfer, make sure that parameter settings are saved to the non-volatile memory as standard parameter set.
Standard Web pages 5.11 Support Transferring files to standard parameter sets in non-volatile memory 1. Proceed as follows to transfer files to standard parameter sets in the non-volatile memory. 2. The transferring process completes when the following window appears. If the Web page indicates that the transfer fails, you can select to transfer again. Note To safely remove the SD card, click "safely remove" on the transfer Web page after the transferring process has completed.
Standard Web pages 5.11 Support 5.
6 Upgrading Upgrading on the SINAMICS G120 Web page upgrades the firmware version of the SINAMICS G120 Smart Access. Two upgrading methods are available: ● Conventional upgrading ● Basic upgrading (applicable when conventional upgrading fails) Conventional upgrading 1. Download the target upgrade file (*.bin file) from the following Web site to your local drive (recommended on PC): https://support.industry.siemens.com/cs/ww/en/ps/13225/dl 2. Access the SINAMICS G120 Web page: http://192.168.1.
Upgrading 3. The upgrading process completes when the following window appears. If the Web page indicates that the upgrading fails, you can select to upgrade again. 4. Restart the SINAMICS G120 Smart Access. Note that if you do not click "Restart G120 Smart Access now", the SINAMICS G120 Smart Access will restart automatically after the 10-second countdown time has elapsed. 5. Clear the browser cache. 6. Refresh your Web application.
Upgrading 4. Proceed as follows: "Format web" is optional. If you click "Format web", the base version and all the bin files and xml files you have backed up will be deleted. 5. Restart the SINAMICS G120 Smart Access. 6. Clear the browser cache. 7. Refresh your Web application. Note Refresh the basic upgrading page if the connection status unexpectedly becomes "disconnected" during upgrading.
Additional information 7.1 7 Product information User documentation ● SINAMICS G120 Smart Access Operating Instructions (https://support.industry.siemens.com/cs/ww/en/ps/13225/man) Commissioning, parameterizing, and maintaining the converter with SINAMICS G120 Smart Access (this manual) ● SINAMICS G120 Smart Access Product Information (https://support.industry.siemens.
Additional information 7.2 Product support 7.2 Product support For more information about the product, please visit: Product support (http://www.siemens.com/automation/service&support) This address provides the following: ● Actual product information (product memorandums), FAQs (frequently asked questions), downloads. ● The Newsletter contains the latest information on the products you use. ● The Knowledge Manager (Intelligent Search) helps you find the documents you need.
Additional information 7.3 Technical specifications 7.3 Technical specifications Feature Description Article number 6SL3255-0AA00-5AA0 Firmware version V01.03.01 Net weight 87.5 g Gross weight 109.7 g Operating ambient temperature 0 °C ... 50 °C under nominal conditions of the connected converter, according to UL requirement Transportation and storage ambient temperature -40 °C ... 70 °C Extreme temperature range -10 °C ...
Additional information 7.4 Directives and standards 7.4 Directives and standards Radio Equipment Directive 2014/53/EU SINAMICS G120 Smart Access is in compliance with Radio Equipment Directive 2014/53/EU. You can download the certificate from the following link: Declaration of conformity (https://support.industry.siemens.
Additional information 7.4 Directives and standards ANATEL ANATEL certificate number: 06121-18-00199 This device must not be protected against harmful interference and it may not cause interference in authorized systems (see below for corresponding text in Portuguese): Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados.
Additional information 7.4 Directives and standards ictQATAR SINAMICS G120 Smart Access fulfills the requirements for ictQATAR. SINAMICS G120 Smart Access fulfills the requirements for NTC. UkrCEPRO SINAMICS G120 Smart Access fulfills the requirements for UkrCEPRO. SINAMICS G120 Smart Access fulfills the requirements for PTA. SINAMICS G120 Smart Access fulfills the requirements for IMDA. TRC Certificate number: TRC/SS/2019/53 SINAMICS G120 Smart Access fulfills the requirements for TRA.
