Operating Instructions
Table Of Contents
- Converter with CU230P-2 Control Units
- Legal information
- Changes in this manual
- Table of contents
- 1 Fundamental safety instructions
- 2 Introduction
- 3 Description
- 4 Installing
- 4.1 Overview of the inverter installation
- 4.2 Installing reactors, filters and braking resistors
- 4.3 Installing Power Module
- 4.4 Installing Control Unit
- 4.5 Connecting inverters in compliance with EMC
- 5 Commissioning
- 6 Adapting the terminal strip
- 7 Configuring the fieldbus
- 8 Setting functions
- 8.1 Overview of the inverter functions
- 8.2 Inverter control
- 8.2.1 Switching the motor on and off
- 8.2.2 Inverter control using digital inputs
- 8.2.3 Two-wire control: method 1
- 8.2.4 Two-wire control, method 2
- 8.2.5 Two-wire control, method 3
- 8.2.6 Three-wire control, method 1
- 8.2.7 Three-wire control, method 2
- 8.2.8 Running the motor in jog mode (JOG function)
- 8.2.9 Switching over the inverter control (command data set)
- 8.3 Setpoints
- 8.4 Setpoint calculation
- 8.5 Motor control
- 8.6 Protection and monitoring functions
- 8.7 Application-specific functions
- 8.7.1 Unit changeover
- 8.7.2 Calculating the energy saving
- 8.7.3 Electrically braking the motor
- 8.7.4 Flying restart – switching on while the motor is running
- 8.7.5 Automatic switch-on
- 8.7.6 Kinetic buffering (Vdc min control)
- 8.7.7 PID technology controller
- 8.7.8 Free technology controllers
- 8.7.9 Monitoring the load torque (system protection)
- 8.7.10 Load failure monitoring
- 8.7.11 Real time clock (RTC)
- 8.7.12 Time switch (DTC)
- 8.7.13 Record temperature via temperature-dependent resistances
- 8.7.14 Essential service mode
- 8.7.15 Multi-zone control
- 8.7.16 Bypass
- 8.7.17 Cascade control and hibernation mode
- 8.7.18 Free function blocks
- 8.8 Switchover between different settings
- 9 Backing up data and series commissioning
- 10 Corrective maintenance
- 10.1 Overview of replacing converter components
- 10.2 Replace Control Unit
- 10.3 Replacing the Control Unit without data backup
- 10.4 Replacing a Control Unit with active know-how protection
- 10.5 Replacing a Power Module
- 10.6 Upgrading the firmware
- 10.7 Firmware downgrade
- 10.8 Correcting an unsuccessful firmware upgrade or downgrade
- 10.9 If the converter no longer responds
- 11 Alarms, faults and system messages
- 12 Technical data
- A Appendix
- Index
Index
Converter with CU230P-2 Control Units
382 Operating Instructions, 04/2014, FW V4.7, A5E34257946B AA
Conveyor systems, 99
Correction manual, 379
Counter-clockwise rotation, 145
Crushers, 88
Current derating, 340
Current input, 110
Current reduction, 320, 326, 334, 345
Cyclic communication, 128
D
Data backup, 251, 256, 261, 262
Data set 47 (DS), 140
Data transfer, 256, 261, 262
Date, 220
DC braking, 131, 198
DC-link overvoltage, 185
DC-link voltage, 185
Delta connection (Δ), 86, 361
Derating
Installation altitude, 355
Digital input, 68, 69, 145
Function, 104
Digital output, 68, 69
Function, 104, 107
Dimensions, 46, 50, 51
DIP switch
Analog input, 110
Direct data exchange, 139
Direction of rotation, 162
Direction reversal, 145
Display parameters, 362
Door mounting kit, 40
Download, 256, 261, 262
Drilling patterns, 46, 50, 51
Drive Data Set, DDS, 249
Drive Data Sets, 249
Drive ES Basic, 40
DTC (Digital Time Clock), 222
Dynamic braking, 202
E
EMC, 79
Energy recovery option, 204
Energy-saving display, 193
ESM, 225
Essential Service Mode, 225
Extruder, 88, 179
F
Factory assignment, 69
Factory settings
Restoring the, 90
Fan, 27, 88
Fans, 99, 178
Fault, 221, 287, 295
Acknowledge, 295, 296
Fault buffer, 221, 295
Fault case, 295
Fault code, 295
Fault history, 296
Fault time, 221, 295
received, 295
removed, 295
Fault value, 295
FFC (Flux Current Control), 171
Field weakening, 361
Fieldbus interfaces, 67, 78
Firmware downgrade, 281
Firmware version, 271, 358, 359, 360, 362
Flow control, 213
Flying restart, 205
Formatting, 252
Free function blocks, 248
Functions
BOP-2, 365
Fan applications, 142
Heating/air-conditioning systems, 142
HVAC, 142
Overview, 141
Pump applications, 142
Technological, 142
G
Getting Started, 377
Grinding machine, 197, 200
GSDML (Generic Station Description Markup
Language), 120
H
Hardware Installation Manual, 377
Hoist drive, 204
Hoisting gear, 202
Horizontal conveyors, 179, 200, 202
Hotline, 378