Operating Instructions
Table Of Contents
- Converter with CU230P-2 Control Units
- Legal information
- Changes in this manual
- Table of contents
- 1 Fundamental safety instructions
- 2 Introduction
- 3 Description
- 4 Installing
- 4.1 Overview of the inverter installation
- 4.2 Installing reactors, filters and braking resistors
- 4.3 Installing Power Module
- 4.4 Installing Control Unit
- 4.5 Connecting inverters in compliance with EMC
- 5 Commissioning
- 6 Adapting the terminal strip
- 7 Configuring the fieldbus
- 8 Setting functions
- 8.1 Overview of the inverter functions
- 8.2 Inverter control
- 8.2.1 Switching the motor on and off
- 8.2.2 Inverter control using digital inputs
- 8.2.3 Two-wire control: method 1
- 8.2.4 Two-wire control, method 2
- 8.2.5 Two-wire control, method 3
- 8.2.6 Three-wire control, method 1
- 8.2.7 Three-wire control, method 2
- 8.2.8 Running the motor in jog mode (JOG function)
- 8.2.9 Switching over the inverter control (command data set)
- 8.3 Setpoints
- 8.4 Setpoint calculation
- 8.5 Motor control
- 8.6 Protection and monitoring functions
- 8.7 Application-specific functions
- 8.7.1 Unit changeover
- 8.7.2 Calculating the energy saving
- 8.7.3 Electrically braking the motor
- 8.7.4 Flying restart – switching on while the motor is running
- 8.7.5 Automatic switch-on
- 8.7.6 Kinetic buffering (Vdc min control)
- 8.7.7 PID technology controller
- 8.7.8 Free technology controllers
- 8.7.9 Monitoring the load torque (system protection)
- 8.7.10 Load failure monitoring
- 8.7.11 Real time clock (RTC)
- 8.7.12 Time switch (DTC)
- 8.7.13 Record temperature via temperature-dependent resistances
- 8.7.14 Essential service mode
- 8.7.15 Multi-zone control
- 8.7.16 Bypass
- 8.7.17 Cascade control and hibernation mode
- 8.7.18 Free function blocks
- 8.8 Switchover between different settings
- 9 Backing up data and series commissioning
- 10 Corrective maintenance
- 10.1 Overview of replacing converter components
- 10.2 Replace Control Unit
- 10.3 Replacing the Control Unit without data backup
- 10.4 Replacing a Control Unit with active know-how protection
- 10.5 Replacing a Power Module
- 10.6 Upgrading the firmware
- 10.7 Firmware downgrade
- 10.8 Correcting an unsuccessful firmware upgrade or downgrade
- 10.9 If the converter no longer responds
- 11 Alarms, faults and system messages
- 12 Technical data
- A Appendix
- Index
Index
Converter with CU230P-2 Control Units
384 Operating Instructions, 04/2014, FW V4.7, A5E34257946B AA
Installing, 91
IOP, 40
Menu, 365
Optimizing the closed-loop speed controller, 176
Order number, 23
Overload, 184, 363
Overview
Manuals, 377
Overview of the functions, 141
Overvoltage, 185
P
p15 macro, 86
Page index, 136
Parabolic characteristic, 171
Parameter channel, 134
IND, 136
Parameter index, 136
Parameter number, 136, 367
Parameter types, 362
Parameter value, 368
PC Connection Kit, 40
PELV, 309
PID controller, 213
PLC functionality, 375
Power distribution systems, 54
Power failure, 207
Power Module, 23
Pressure control, 213
Procedure, 21
Process variables of the technology controller, 190
PROFIBUS, 123
PROFIdrive, 117
PROFIenergy, 117
Protection functions, 142
Protective conductor, 54
PTC sensor, 180
Pulse cancelation, 129
Pulse enable, 129
Pulse frequency, 178, 179, 320, 326, 334, 340, 345,
364
Pump, 27, 88, 99
Q
Questions, 378
Quick stop, 143
R
Radio interference class, 30
Ramp-down, 363
Ramp-down time, 89, 167, 363
Ramp-function generator, 162
Ramp-up, 363
Rampup time,
Ramp-up time, 167
RDY (Ready), 288
Ready, 144
Ready to switch on, 144
Real time clock, 220
Real Time Clock, 220
Regenerative feedback, 28, 204
Regenerative power, 195
Reset
Parameter, 90
Reversing, 162
Roller conveyors, 88
Rotary furnace, 88
Rounding, 167
Rounding OFF3, 167
RTC (Real Time Clock), 220, 222
S
S7 communication, 117
Saw, 197, 200
Scaling
Analog input, 110
Analog output, 113
SD (memory card), 252
Formatting, 252
MMC, 252
Sequence control, 143
Series commissioning, 251
Setpoint processing, 142, 162
Setpoint source, 142
Selecting, 156, 157, 362
Settling time, 88
Shield connection kit, 28
Short-circuit monitoring, 181
Signal interconnection, 373
Signal states, 288
Sine-wave filter, 36
SIZER, 378
Skip frequency band, 112, 162
Speed
change with BOP-2, 365
Limiting, 162
Speed deviation, 219