User Manual

ManualsBrandsSiemens ManualsBuilding automationGAMMA Catalog 2019

GAMMA instabus

OEM-Product Catalogue

Release: 12/2015

Application Program Bus Interface Modules M130, M131, M132 and M135

Runtime Environment for KNX-Processors 184/11 and 184/21

Siemens AG pages 17 Technical Manual

Building Technologies

Control Products and Systems

P. O. Box 10 09 53, © Siemens AG 2015 page 1

D-93009 Regensburg Subject to change without further notice.

Content of this document:

1 Memory map .................................................................................................................. 2

1.1 BIM M 130, BIM M 135 and Chipset 184/01 ............................................................ 2

1.2 BIM M 131 and Chipset 184/11 ............................................................................... 3

1.3 BIM M 132 and Chipset 184/21 ............................................................................... 4

2 Task switch system ........................................................................................................ 5

3 User application program ............................................................................................... 7

4 Communication object handling .....................................................................................10

5 How to make a RELEASE .............................................................................................11

5.1 S19 for download via bus .......................................................................................11

5.2 Download with flash programmer ...........................................................................15

5.2.1 PG-FP5 ...........................................................................................................15

6 Release Notes for new firmware revisions .....................................................................17

6.1 Introduction ............................................................................................................17

6.2 Firmware revision 2.00 ...........................................................................................17

6.2.1 Timer ...............................................................................................................17

6.2.2 TPUART-Communication ................................................................................17

6.2.3 FT12-Communication ......................................................................................17

6.3 Firmware revision 2.01 ...........................................................................................17

6.3.1 Internal timing..................................................................................................17

Document-Version: 2.2

Summary of content (17 pages)

PAGE 1
GAMMA instabus OEM-Product Catalogue Release: 12/2015 Application Program Runtime Environment for Bus Interface Modules M130, M131, M132 and M135 KNX-Processors 184/11 and 184/21 Content of this document: 1 Memory map .................................................................................................................. 2 1.1 BIM M 130, BIM M 135 and Chipset 184/01 ............................................................ 2 1.2 BIM M 131 and Chipset 184/11 ..............................
PAGE 2
GAMMA instabus Release: 12/2015 Application Program Runtime Environment for Bus Interface Modules M130, M131, M132 and M135 KNX-Processors 184/11 and 184/21 1 Memory map To provide compatibility with ETS the operating system does a memory translation from bus addresses to the internal addresses of the microcontroller. That means that for example the start of the address table for the ETS is 0x0116 and in reality it is 0x8116 in the microcontroller.
PAGE 3
GAMMA instabus Release: 12/2015 Application Program Runtime Environment for 1.2 Bus Interface Modules M130, M131, M132 and M135 KNX-Processors 184/11 and 184/21 BIM M 131 and Chipset 184/11 Address in F0535 Bus access address Used by Type 0xFEDF 0xFBD0 n.a. System RAM 0xFBCF 0xFB00 n.a. User (Stack and Variables) RAM 0xF7FF 0xF400 n.a. System RAM 0xF3FF 0xF000 n.a. User (Variables) RAM 0xEFFF 0xD000 n.a. System (Reserved) Flash 0xCFFF 0xC000 n.a. User (Appl.
PAGE 4
GAMMA instabus Release: 12/2015 Application Program Runtime Environment for 1.3 BIM M 132 and Chipset 184/21 Address in F0537 Bus access address Used by Type 0xFEDF 0xFBD0 n.a. System RAM 0xFBCF 0xFB00 n.a. User (Stack and Variables) RAM 0xF7FF 0xF400 n.a. System RAM 0xF3FF 0xE000 n.a. User (Variables) RAM n.a. System (Reserved) Flash n.a. User (Appl.
PAGE 5
GAMMA instabus Release: 12/2015 Application Program Runtime Environment for Bus Interface Modules M130, M131, M132 and M135 KNX-Processors 184/11 and 184/21 2 Task switch system To allow the implementation of the user application program in an endless loop the operating system provides a simple task switch system, that interrupts the user application program every 3.3ms for one complete system cycle. User application program Operating System user cstartup AppInit() 3.3ms main loop of the user appl.
PAGE 6
GAMMA instabus Release: 12/2015 Application Program Runtime Environment for Bus Interface Modules M130, M131, M132 and M135 KNX-Processors 184/11 and 184/21 The switch between register sets is used to enhance performance.
PAGE 7
GAMMA instabus Release: 12/2015 Application Program Runtime Environment for Bus Interface Modules M130, M131, M132 and M135 KNX-Processors 184/11 and 184/21 3 User application program The user application program has to be developed as a regular program for a Renesas 78K0 microcontroller, but with some modifications. To give the possibility to debug the user application program on the evaluation board there are some special differences to a normal program for the 78K0.
PAGE 8
GAMMA instabus Release: 12/2015 Application Program Runtime Environment for Bus Interface Modules M130, M131, M132 and M135 KNX-Processors 184/11 and 184/21 The ‘NEAR_ID’ contains the value for the ram variables that have to be initialized at startup of the user application program through ‘cstartup’. Const data is placed in ‘CONST’. The segment ‘RCODE’ contains the ‘cstartup’ code and the runtime library code. ‘CODE’ contains the normal program code.
PAGE 9
GAMMA instabus Release: 12/2015 Application Program Runtime Environment for Bus Interface Modules M130, M131, M132 and M135 KNX-Processors 184/11 and 184/21 Each user application program must have a user application information block. This block has always to be at 0x8000.
PAGE 10
GAMMA instabus Release: 12/2015 Application Program Runtime Environment for Bus Interface Modules M130, M131, M132 and M135 KNX-Processors 184/11 and 184/21 4 Communication object handling All communication objects of the application program are defined in table ‘EE_CommsTab’. The table starts with a byte that specifies the number of communication objects. The next byte is only implemented for compatibility and should be 0x00. After this per communication object three bytes are defined.
PAGE 11
GAMMA instabus Release: 12/2015 Application Program Runtime Environment for Bus Interface Modules M130, M131, M132 and M135 KNX-Processors 184/11 and 184/21 5 How to make a RELEASE There are two possibilities that could be done with a ready developed BIM M 13x application. First a S19 file could be generated for an ETS database entry. For this the KNX manufacturer tool is necessary.
PAGE 12
GAMMA instabus Release: 12/2015 Application Program Runtime Environment for Bus Interface Modules M130, M131, M132 and M135 KNX-Processors 184/11 and 184/21 The xml configuration file has the following structure: ... ...
PAGE 13
GAMMA instabus Release: 12/2015 Application Program Runtime Environment for Bus Interface Modules M130, M131, M132 and M135 KNX-Processors 184/11 and 184/21  00 4E 001 1 010203040506 Generates a ‘property compare’. In this example the value of the property 0/78 (Hex: 0x4E) is compared with the value ‘0x01 0x02 0x03 0x04 0x05 0x06’.
PAGE 14
GAMMA instabus Release: 12/2015 Application Program Runtime Environment for Bus Interface Modules M130, M131, M132 and M135 KNX-Processors 184/11 and 184/21  ... ... ... This load control specifies an address range that will be downloaded to the device. The ETS only loads the data that are specified within this range.
PAGE 15
GAMMA instabus Release: 12/2015 Application Program Runtime Environment for 5.2 Bus Interface Modules M130, M131, M132 and M135 KNX-Processors 184/11 and 184/21 Download with flash programmer To generate a S19 file that can be downloaded with the Renesas flash programmer the IAR Embedded Workbench must output a normal S19 (S37 in case of BIM M 132 / chipset 184/21) file.
PAGE 16
GAMMA instabus Release: 12/2015 Application Program Runtime Environment for Bus Interface Modules M130, M131, M132 and M135 KNX-Processors 184/11 and 184/21 Last click on button "OK" to store the download file and the settings in the PG-FP5 flash programmer. Use command "ep" (erase and program) to download the S19 (or S37) file to the device. After successful programming download via bus the S19 file that was created by the modifier with the config_pgfp4.xml file.
PAGE 17
GAMMA instabus Release: 12/2015 Application Program Runtime Environment for Bus Interface Modules M130, M131, M132 and M135 KNX-Processors 184/11 and 184/21 6 Release Notes for new firmware revisions 6.1 Introduction New firmware revisions will improve the stability of the operating system. All applications that are developed with older firmware revisions can still be used with new firmware revisions without recompiling or any modifications. 6.2 Firmware revision 2.00 6.2.