User Manual

s
GAMMA building control – energy-efficient building and room automation
EnOcean gateway
IR receiver/decoder
GAMMA touch panel
GAMMA instabus pushbutton Actuators for switching,
dimming, sun protection
and room climate
wave coupler
EnOcean wall-mounted
transmitter and room
control units
IR hand-held and
wall-mounted
transmitters
GAMMA wave hand-held
and wall-mounted
transmitters
GAMMA instabus – KNX
Control elements can be mounted however you wish, without additional
wires, through flexible installation of no-maintenance, no-battery sensors
with EnOcean technology. The sensors for lighting, sun protection and room
climate applications are integrated into the building automation
systems using an EnOcean gateway. EnOcean devices can be combined
with all DELTA miro and DELTA line frames.
Infrared systems are used if radio is not feasible on legal, technical or health
reasons. Functions are often to be controlled from any point in the room. This
is possible with infrared. Because data transfer from the remote is restricted to
the actual room, there is no interference affecting all rooms. You can even take
the hand-held transmitter with you to control the corresponding functions in
other rooms.
You can carry out numerous modern electrical installation functions without
having to lay additional wires, using the GAMMA wave radio system. This is
particularly advantageous when redeveloping, renovating and modernizing.
The bi-directional radio system meets the KNX standard.
Infrared system GAMMA wave radio system – KNX-RFEnOcean radio system
GAMMA instabus is based on the proven, globally implemented standard KNX in accordance with EN 50090 and ISO/IEC 14543. KNX forms the basis for a comprehensive building automation in the electrical installation. Wireless systems can be
incorporated during installation for increased flexibility. These include infrared and radio systems. These technologies are connected to KNX via gateways. Various display and operating elements to operate the room functions are available to the
user with all technologies – from simple pushbuttons through multi-functional room control units up to web-based systems.
www.siemens.com/gamma
GAMMA building control – display and operation
BuildingRoom
Basic operation
GAMMA instabus pushbutton in
different designs for typical room
functions
Remote operation
Hand-held and wall-mounted trans-
mitters for infrared (IR), KNX-RF and
EnOcean, for typical room functions
Operation and control
Fan-coil unit operating device and
room temperature controller in
various designs
Display and operation
Multi-functional room control units
in various designs and operating
modes
KNX-based central displays and
operation
Central display and operation device
with additional special applications
Web-based monitoring and
operating
Browser-based application for multi-
site KNX infrastructure coverage
with IT standard communication
Design
– Pushbutton with/without status
LED
– Pushbutton with status LED, scene
control and room temperature
controller
– Pushbutton with status LED, scene
control and IR receiver/decoder
– Wide design and color selection
Functions
– Lighting, sun protection, heating,
ventilation and climate control
– Switching (On/Off, toggling)
– Bell function
– Dimming
– Sun protection control
(shutters, blinds)
– Scene control, effect control
(recall, save)
– Transfer of different values
(percentages, temperature values,
brightness values, etc.)
Design
– Hand-held transmitter
(IR, KNX-RF)
– Wall-mounted transmitter
(IR, EnOcean)
– Flush-mounted transmitter
(IR, KNX-RF)
– Wide design and color selection
Functions
– Lighting, sun protection, heating,
ventilation and climate control
– Switching
– Dimming
– Sun protection control
(shutters, blinds)
– Scene control
– Transfer of different values
(percentages, temperature values
brightness values, etc.)
Design
– Fan-coil unit controller
– Room temperature controller
– Wide design and color selection
Functions
Fan-coil unit controller:
– Control of fan-coil unit functions,
such as temperature and fan
speeds
– Switch between comfort and
energy-saving modes
– Fan speed display using five yellow
LEDs
– Display current room operating
mode and heating/cooling mode
Room temperature controller:
– Heating, cooling and combined
heating/cooling operation
– Changing nominal value
– Toggling between comfort and
standby modes
– Display current room operating
mode
Design
– Text display
– Room control unit
– Wide design and color selection
Functions
– Lighting, sun protection, heating,
ventilation and climate control
– Display of various values
(temperatures, brightness,
consumption), text messages,
current operating mode, current
fan speed, etc.
– Alarms
– Date and time display
– Timer program with weekly
schedules
– Scene control
– Room temperature controller
– Changing nominal value and
operating mode
– Setting fan speed
Design
– Color touch panel as multi-function
display/operation unit
– Wide design and color selection
Functions
– Display and operation of up to
110 KNX functions on 20 display
and operating pages
– Timer program with weekly
schedules
– Presence simulation
– Scene control (64 scenes)
– 32 logic functions
– Trending module
– Alarm page with display and
reporting of a max. of 16 alarm
reports
– Individual password protection
for each page
– Integrated real-time clock, date
and time display
– Display of individual images on
the start page
– Configurable slide show
Design
– N151 IP Viewer
Functions
– Lighting, sun protection, heating,
ventilation and climate control
– KNX system data visualization
and operation
– Display of up to five operating
pages in a standard web browser,
with up to 40 display and
operating functions
– Configurable start page