Poster

031_A6V10449315(AA)
Gamma Lighting Control – Field Devices
Photo Description Product Number
a
Dimensions
Current or Power
Draw on KNX Bus
Required Additional
Gamma parts
Notes
Technical
Product Info
(TPI)
Install
Instructions
(BMA)
Application Program
Description (APB)
Switches, HMI & Switch Accessories
Delta profil Wall Switches (UP 24x)
1, 2, or 4 pairs of upper and lower push buttons, titanium
white. Each pair of push buttons may be defined for
switching, dimming, or controlling shutters and blinds.
Includes a panel for labels, one status LED per button pair,
and one orientation LED for the switch.
2.56" × 2.56" × 0.43"
(65 × 65 × 11 mm)
Bus power:
provided through the
BCU UP 110/03
3 mA
• Delta profil frame (10-pack)
(5WG1 240-8CB11),
• BCU UP 110/03
(5WG1 110-2CB03)
Single Push Button (UP 241)
5WG1 241-2AB11 1 pair (or 2 individual) push buttons 211301
Double Push Button (UP 243)
5WG1 243-2AB11
2 pair (or 4 individual) push buttons
221301
Quadruple Push Button (UP 245)
5WG1 245-2AB11
4 pair (or 8 individual) push buttons
241301
241901
Infrared Receiver Decoder (S 450)
Control pickup (ceiling mount). Translates the infrared
control signals from the Infrared Remote S 425/72 into bus
telegrams.
Emulates 16 button pairs or 32 individual buttons when
used with one remote, or 32 button pairs or 64 individual
buttons when used with two remotes.
5WG1 450-7AB03
0.98” × 1.0” × 2.95”
(25 × 26 × 75 mm)
with 1.89" (48 mm) Ø
trim ring
8 mA
• IR remote S 425/72
(5WG1 425-7AB72)
• Programming magnet
AP 590H (5WG1 590-8AH01)
(Also see Notes )
Most ceramic or stronger magnets can be used in lieu of
AP 590H to activate programming mode.
154-123 A5E01134709 909201
Infrared Remote (S 425/72)
Silver. Offers remote control of 16 different room functions
through four pairs of buttons and four pre-selection buttons.
A separate central pair of buttons can be used to operate
the central function associated with the buttons.
5WG1 425-7AB72
2.1" W × 6.1" L × 0.9" H
(55 × 154 × 24 mm)
–
Transmission Range
Approximately 65 ft (20 m) with clear line
of sight to receiver.
Functions with:
• IR Receiver Decoder (S 450)
Requires two alkaline LR03/AAA, 1.5V batteries (not
included).
154-111 A5E02227390A –
Delta profil Frame for Nema Boxes
Used with wall switches and motion sensors. 2 × 4 wall
mount, titanium white, 10-pack.
5WG1 240-8CB11
3.15" × 4.72"
(80 × 120 mm)
–
Must be ordered in multiples of 10. One pack contains 10
frames.
– – –
Bus Coupling Unit (BCU) (UP 110/03)
Connects application units (for example, Wall Switches UP
245) to the bus line.
5WG1 110-2CB03
4.5" × 2.7" × 1.02"
(115 × 69 × 27 mm)
N/A
Load depends on
device installed
on the BCU.
Installation
Mount in either a single-gang NEMA-type wall box,
minimum interior wall box size (H × W × D): 3.5" × 1.97"
× 1.57" (89 mm × 50 mm × 40 mm), or a single-gang
data ring.
154-096 2515104107
Use the APB for
the installed
switch or sensor.
Push Button Interfaces (UP 220/x1)
Binary input for monitoring non-Gamma switches, relays, or
other contact devices using the Gamma system. Each
channel may be used as either a dry-contact input or an
output for control of a light emitting diode (LED). The
required voltage is provided by the push button interface
(requires no additional power supply).
1.65" × 1.65" × 0.43"
(42 x 42 x 11 mm)
8 mA
Input
For connection to dry contact
• Open circuit voltage: 29 Vdc
• Short circuit current: 0.2 mA DC
Output
For connection to an LED only.
• Voltage: 4.7 Vdc
• Current: 2.5 mA DC (limited
by internal 1.9K Ω resistor)
Signal cable set length: 11" (280 mm) unshielded. May
be extended up to 33 ft (10 m) (per channel) with twisted,
unshielded cable.
Installation
May be installed in a wall switch box if only low voltage is
present.
2 I/O Push Button Interface (UP 220/21)
5WG1 220-2AB21 982302
4 I/O Push Button Interface (UP 220/31)
5WG1 220-2AB31 982202
Sensor Detection Range
Weather Stations (AP 257/x2)
Façade control, with GPS receiver, surface mounted. For
control of interior or exterior shades and blinds, exterior
lighting and signs, based on exterior light levels. Can
override sprinkler systems when rain is present. Also used
to monitor outside temperature, wind speed, and light level.
4.65” × 3.78”× 3.03”
(118 × 96 × 77 mm)
Temperature sensor
-22°F to 122°F (-30°C to 50°C)
Brightness sensor
0 to 150,000 lux
Wind sensor
0 to 78 mph (0 to 125 kmh)
• Location set by GPS or manual entry
• Astronomical clock
• Dusk/dawn controls
• Rain sensor

(see Notes)
Can receive power from one of the following:
• 20 Vac (do not use 24 Vac nominal) 50/60 Hz Class 2
• 12 to 40 Vdc Class 2, 2.3 VA (185 mA at 12 Vdc,
93 mA at 24 Vdc)
• Residual ripple < 10%
• Maximum permissible cable length 330 ft (100 m)
Advanced Weather Station (AP 257/22), 8 façade control
5WG1 257-3AB22
8 façades, shade/blinds continuous control
• Shadow edge tracking
• Sun tracking
A5E02422958D 914201
Basic Weather Station (AP 257/32), 4 façade control
5WG1 257-3AB32
4 façades, shade/blinds open/close/preset
control
A5E02423026D 914301
Brightness Controllers (UP 255/11 and AP 255/12)
For automatic control of workplace and room lighting in
response to ambient light levels (daylight harvesting). The
control can be set to either On/Off brightness control for
switchable luminaires or constant light level control for
dimmable luminaires.
Bus current:
15 mA
Measuring range
0 to 2000 Lux (with a reflection degree
from the working surface of about 30%)
Factory-calibrated for direct readings.
Can be site calibrated for indirect readings
using ETS or calibration remote.
Optional accessory
IR remote control (5WG1 255-7AB01) for wireless
commissioning, calibration of brightness measurement
and for switching KNX addressing mode On and Off to
load a physical address.
Brightness Controller (UP 255/11), flush-mount
5WG1 255-4AB11
1.97” H × 3.5” Ø
(50 × 89 mm)
Height includes 1.1"
(28 mm) exposed fiber
optic light guide.
Installation
May be attached directly to the mounting surface with
screws, or installed in a junction box that complies with
DIN 49073–GB-T-M1E1 (02/90), Ø 2.36” (60 mm), depth
1.57” (40 mm).
NOTE:
Installation in ceiling tiles requires two bolts, nuts,
and washers (not included).
Brightness Controller (AP 255/12), surface-mount
5WG1 255-4AB12
2.16" H × 2.95” Ø
(55 × 75 mm)
Height includes 1.1"
(28 mm) exposed fiber
optic light guide.
Installation
Surface mounting
IR remote calibration (S 255)
For wireless calibration of brightness measurement and
for switching KNX addressing mode On and Off to load a
physical address.
5WG1 255-7AB01
3.4" × 1.6" × 0.2"
(87 × 40 × 6 mm)
Transmission range
• Cloudy conditions 19.7 ft (6 m)
• Direct sunshine 6.5 ft (2 m)
Functions with:
• Brightness Controllers
UP 255/11 and AP 255/12
Requires one Lithium button cell CR2025 battery
(supplied with the device).
– A5E02123817A –
Dual Sensor for Brightness & Temperature
(AP 254/02)
Applications: multi-staged lighting controls,
open/close/preset control of awnings/blinds/shutters.
Also used to monitor outside temperature and light level.
5WG1 254-3EY02
4.33” × 2.83” × 2.24”
(110 × 72 × 57 mm)
5 mA
Light level sensor
1 to 100,000 Lux
Temperature sensor
-22°F to 140°F (-30°C to 60°C)
Aperture
• Horizontal: +/- 60°
• Vertical: –35° to 66.5°
154-116 A5E01594561C 909712
Sensor Detection Range
Motion Detectors (UP 255)
Proximity sensor which reacts to movements of people,
animals or other moving objects. Includes detatchable
masking plate to restrict horizontal monitoring area.
Titanium white, wall-mount.
2.56” × 2.56” × 1.18”
(65 × 65 × 30 mm)
Bus power:
provided through the
BCU UP 110/03
• Brightness measurement used
for internal calculations only; not
available to other devices.
• Horizontal detection angle:
180° on two levels.
• Delta profil frame
(5WG1 240-8CB11)
• BCU UP 110/03
(5WG1 110-2CB03)
Potentiometer for stepless adjustment of the monitoring
distance between 6 and 33 ft (1.8 and 10 m).
Motion Detector, mounting height 43" (1.10 m)
5WG1 255-2AB11
See Notes
Range at mounting height of 43" (1.10 m):
• Forward: approx. 33 feet (10 m)
• Lateral: 2 × approx. 19.7 feet (6 m) each side
Motion Detector, mounting height 86" (2.20 m)
5WG1 255-2AB12
See Notes
Range at mounting height of 86" (2.20 m):
• Forward: approx. 33 feet (10 m)
• Lateral: 2 × approx. 19.7 feet (6 m) each side
Range at mounting height of 43" (1.10 m):
• Forward: approx. 17 feet (5 m)
• Lateral: 2 × approx. 10 feet (3 m) each side
Presence/Motion Detectors with Integrated Brightness
Controller
Provides automatic lighting control based on occupancy or
vacancy. May also be used for automatic control of one
main lighting group and up to four additional lighting
groups in response to ambient light levels (daylight
harvesting). Includes three timers for control of separate
functions. Integrated IR-receiver for an IR-remote control.
Without design cover:
2.1” × 1.2” (53 × 31 mm)
With design cover:
3.46” × 2.48” (88 × 63 mm)
• Passive IR presence detection:
horizontal 360°
• Brightness measuring:
20 to 1000 Lux.
Also see Notes
• Includes detatchable masking plate to
restrict width of monitoring area.
• Factory-calibrated for direct readings.
Can be site-calibrated for indirect
readings using ETS.
• Sensor head can be rotated +/- 50° and
tilted -5°/+25° for aiming.
• Emulates 6 button pairs or 12
individual buttons when used with
optional remote.
Detection range increases as ceiling height increases.
• Range at 8.2 ft (2.50 m) ceiling height: 14.8 × 9.8 ft
(4.5 × 3 m).
• Range at 12.3 ft (3.75 m) ceiling height:
26.2 × 14.8 ft (8 × 4.5m).
Recommended mounting height for mixed light
measurement: 8.20 ft to 9.20 ft (2.5 m to 2.8 m).
Installation
Ceiling mount. Spring clips included for installation in
ceiling tiles or panels up to 1-3/16" (30 mm) thick. May
be attached directly to the mounting surface with screws
(not included), or installed in a junction box that complies
with DIN 49073–GB-T-M1E1 (02/90), Ø 2.36” (60 mm),
depth 1.57” (40 mm).
OPTISENS Office (UP 258D11)
Motion and on/off light control.
5WG1 258-2DB11 10 mA
Optional accessory
IR remote control (5WG1 255-7AB11)
A5E03735060A 910501
OPTICONTROL Office (UP 258E21)
Motion and constant light level control.
5WG1 258-2EB21 10 mA
Optional accessory
IR remote control (5WG1 255-7AB11)
A5E02676917A 910601
AP Housing (AP 258E01)
Surface-mounting box.
5WG1 258-7EB01
1.7" H × 3.4" Ø
(87 × 44 mm)
–
2.13.1.7 – –
IR remote control (S 255/11)
Sends control signals to the presence detectors UP
258/D11 and UP 258E21.
5WG1 255-7AB11
3.4" × 1.6" × 0.2"
(87 × 40 × 6 mm)
Transmission range
Cloudy conditions 19.7 ft (6 m)
Direct sunshine 6.5 ft (2 m)
Functions with:
• OPTISENS (UP 258D11)
• OPTICONTROL (UP 258E21)
Requires one Lithium button cell CR2025 battery
(supplied with the device).
– A5E02421204A –
Outdoor/Indoor Surface-Mount Motion Detector (AP
251/11)
Detects body heat radiated in its capture zone. Suitable for
mounting on a wall or 90° outside corner. IR remote control
available for setting device mode, brightness threshold,
and delay time. Titanium white.
5WG1 251-3AB11
7.09” × 3.39” × 2.91”
(180 × 86 × 74 mm)
Tilting arm adjustment zone:
Maximum 120°
11 mA
Capture zone: 290°
Range (at mounting height
8 ft, +72°F [2.5 m, +22°C])
Approx. 52 ft (16 m)
Dawn/twilight sensor
0.5 to 2000 lux (factory set 7 lux)
Timer adjustable from 5 seconds to 30
minutes.
Installation
Mounting height: 6.5 to 13 ft (2 to 4 m), ideally 8 ft
(2.5 m).
Optional accessories
• Base for mounting on a 90° outside corner
(5TC7 900)
• IR remote control (5TC7 902), which allows
adjustments that otherwise require removing device
from mounting bracket.
909101
Base
For mounting the Outdoor/Indoor Surface-Mount Motion
Detector (AP 251/11) on a 90° outside corner.
5TC7 900
4.1" × 3.4"
(104 × 86.4 mm)
–
IR Remote Control
For calibration of brightness measurement and delay time
and for selecting operating mode of the Outdoor/Indoor
Surface-Mount Motion Detector (AP 251/11).
5TC7 902
3.4" × 1.6" × 0.2"
(87 × 40 × 6 mm)
Transmission range
Cloudy conditions 19.7 ft (6 m)
Direct sunshine 6.5 ft (2 m)
Functions with:
• Outdoor/Indoor Surface-
Mount Motion Detector
(AP 251/11)
Requires one Lithium button cell CR2025 battery
(supplied with the device).
251652.41.15 –
Contouch Room Controller (UP 204/x1)
Multifunctional display/operating device for a KNX system.
Provides 18 configurable room operator functions.
Operation using touch screen and/or by turning/pushing the
rotary/push button. Titanium white.
5WG1 204-2AB11
4.57" × 3.39" × 1.18"
(116 × 86 × 30 mm)
Including rotary/push button
10 mA
• Provides display and control of
shades, blinds, lighting, scenes plus
alarm messages.
• 7-day schedule for 18 control
functions, which may be switched
up to 16 times per day.
Contouch Flash Kit for
programming (5WG1 204-
8AB01). One per project.

24 Vdc
(12 to 30V),
50 mA
Includes the bus coupling unit (BCU).
Installation: Mounts in a Ø 60 mm box.
Contouch Flash Kit
With microSDHC card and 2 adapters. For transferring
firmware and configuration data.
5WG1 204 8AB01
Consists of a removable data carrier, a micro SDHC card
with two adapters, a micro SD adapter and a USB micro
SD reader.
Color Touch Panel (UP 588/23)
Multi-functional color display/control device for a KNX
system. Pressure-sensitive areas permit operation with
long and short button presses, similar to a wall switch.
5WG1 588-2AB23
6.18” × 5.16” × 2.36”
(157 × 131 × 60 mm)
See Notes
• 10 separate pages, each providing
5 main functions with optional
feedback, and 6 additional control
objects.
• Pages may be individually
password protected.
• Day of the week scheduling
• Logic functions
• Scenes
• Trending
• Frame (5WG1 588-8AB1x )
• Back Box (5WG1 588-8EB01)

(see Notes)
External power supply:
• 18 to 36 Vdc, 400 mA
• 14 to 28 Vac, 400 mA
A5E02834306C 910201
Frame for Touch Panel 5.7", Brushed Aluminum
5WG1 588-8AB12 – –
Frame for Touch Panel 5.7", Steel
5WG1 588-8AB13 – –
Frame for Touch Panel 5.7", Black Glass
5WG1 588-8AB14 – –
Back Box for UP588 Touch-Panel, Flush-Mount.
5WG1 588-8EB01
6.36” × 5.31” × 2.52”
(161.5 × 135 × 64 mm)
Mounting depth in flush-mounting box: 2.52” (64 mm)
NOTE: Order P/N 5WG15888EB011
– –
NOTES:
a) When entering a Product Number in SAP, do not use spaces or dashes. For example, Product Number 5WG1 141-1AB02 is entered as 5WG11411AB02.
Basic Wiring Diagram for Dimming.
Basic Wiring Diagram for Switching or Dimming Using the Gamma KNX/DALI Gateway N 141/02.
154-124
7.63” × 6.14” × 0.2”
(194 × 156 × 5 mm)
Touch Panels
154-105
Occupancy Sensors
External
Power
Supply
Required
Product Features
Documentation Product Numbers
A5E02660299 A5E02551184
154-098 251523.41.11
154-114
154-117 A5E01251123B 909601
Sensors/Controllers
211D01 (stand-alone)
211E01 (master)
211F01 (extension)
154-108
2.12.1.14 L1V30068787 970005
154-106
A5E01251127C
251516.41.81