User guide

7
Athen / GBR / A31008-M1801-L101-1-7619 / Athen_en_Kombi.fm / 11.08.2006
Internal listening in
You want to listen in to an existing external call.
Press and hold the talk key
c. You are linked into
the call. All participants hear a beep.
To end: press the end call key
a. All participants
hear a beep.
If the first internal participant presses the end call
key
a, the handset that has 'listened in' remains
connected to the external caller.
Handset settings
Change display language
MENU ¢ Settings ¢ OK ¢ Handset ¢ OK
¢ Language ¢ OK ¢ Select the language
¢ OK
The current language is indicated by ‰.
If you accidentally choose a language you do not
understand:
MENU
¢ 321 (Press the keys one after the other)
Select the correct language with u and press OK.
Setting the alarm clock
Activating/deactivating the alarm clock
MENU ¢ Alarm Clock ¢ OK ¢ Activation
¢ OK (‰ =on)
Or: Press the alarm clock key g.
When the alarm clock rings, press any key to switch
it off for 24 hours.
Setting the wake up time
MENU ¢ Alarm Clock ¢ OK ¢ Wake-up time
¢ OK
Enter the wake up time in hours and minutes, then
press OK.
Resetting the handset
You can reset any individual settings and changes
that you have made. Entries in the directory, the
calls list and the handset's registration on the base
station will be retained.
MENU ¢ Settings ¢ OK ¢ Handset ¢ OK
¢ Reset Handset ¢ OK
Cancel the reset with
a.
Base station settings
The base station settings are carried out using a
registered handset.
Restoring the base station to the factory
settings
When the settings are restored all handsets are de-
registered. The individual settings are reset. Only
the date and time are retained.
MENU ¢ Settings ¢ OK ¢ Base ¢ OK
¢ Base Reset ¢ OK
If you have forgotten your system PIN you can reset
the base station to the original code 0000:
Disconnect the power cord from the base station.
Hold down the registration/paging key (page 1) on
the base station while reconnecting the power
cable to the base station at the same time. Release
the key after a time.
The base station has now been reset and the sys-
tem PIN 0000 set.
Operating the base station on the PABX
The following settings are only necessary when
your PABX requires them, see the PABX user guide.
Changing the dialling mode
MENU ¢ 33911 ¢ The number for the set
dialling mode flashes: 0 = Touch tone dialling
(DTMF); 1 = Dial pulsing (DP)
¢ Enter number
¢OK.
Setting the flashing time
MENU ¢ IIO12 ¢ The number for the cur-
rent flashing time flashes
: 0 =80ms; 1 =100ms;
2 = 120 ms; 3 = 400 ms; 4 = 250 ms; 5 = 300 ms;
6 = 600 ms; 7 = 800 ms ¢ Enter number ¢ OK.
Changing pause after line seizure
You can set the length of the pause inserted
between pressing the talk key
c and sending the
phone number.
MENU ¢ IIO1O ¢ The number for the current
pause length flashes: 1 = 1 sec.; 2 = 3 sec.; 3 = 7 sec.
¢ Enter number ¢ OK.
Changing the pause after the recall key
MENU ¢ IIO14 ¢ The number for the current
pause length flashes: 1 = 800 ms; 2 = 1600 ms;
3 = 3200 ms ¢ Enter number ¢ OK.