Instruction manual

Bulletin 700-P
Heavy-Duty Industrial Relays
9-124
www.ab.com/catalogs Preferred availability cat. nos. are b
bold
.
Publication A117-CA001A-EN-P
Accessories
0
1
2
3
4
5
6
7
8
9
10
11
12
13
Description Pkg. Quantity Cat. No.
Surge Suppressors (RC Circuit) — Surge suppressors reduce
the high transient voltages generated when the coil circuit is
opened. These suppressors can be used with Bulletin 700-P, -
PH, -PK, and -N relays, and other electromechanical devices.
They contain a resistor and capacitor. Maximum ratings: 150V,
AC or DC, 35 VA. Cat. No. 700-N5 requires 1 in. additional depth
of enclosure.
Mounting behind
relay 1
700-N5
Surge Suppressor
Cat. No. 700-N5
Mounting on coil
terminal
1
700-N24
Surge Suppressor
Cat. No. 700-N24
Surge Suppressor
When the circuit to a DC operating coil is opened, the inductive
energy stored in the coil can generate very high transient voltages.
With the addition of the appropriate surge suppressor, the stored
energy is absorbed and dissipated limiting the voltage spikes. A
surge suppressor is not required with AC 700-R or -RM relays
because the AC operating coil transients are suppressed by a full
wave rectifier connected to the coil.
24…48V AC/DC 1
199-FSMA9
50…120V AC/DC 1
199-FSMA10
130…250V
AC/DC
1
199-FSMA11
Surge Suppressor
Cat. No. 199-FSMA1
Diode Surge Suppressor — for 6…300V DC voltage coils. Used on Bulletin 700-P, -
PH, -PK, -N, -F, and -R relays.
1
199-FSMZ-1
35 A Jumper Kit – CSA Approved, UL Listed
This 35 A Jumper Kit can be used with any Bulletin 700-P and -PK AC or DC relay,
Time-Delay relay or Latch Unit equipped with 20 A Master Cartridges. It does not
require any additional panel space.
Jumper Kit terminals are designed for one #8 AWG wire or two #10 AWG wires. When
connecting the two 20 A Master Cartridges in parallel, it is important that they be the
same configuration (Normally Open or Normally Closed).
Jumpers can be added to any contact cartridge location on a relay except the two
center poles because of the wide spacing. An adhesive label is included with each kit
listing the contact ratings.
1
700-CPH
35 A Jumper Kit
Cat. No. 700-CPH
Jumpers (Not applicable for Bulletin 700-PH or -PK relays) – For
connection between a middle pole and an outer pole on the left or
right side of the relay.
Jumper – For
outer poles
50
700-N3
Jumper
Cat. No. 700-N3
Jumper
Cat. No. 700-N4
Jumpers (Not applicable for Bulletin 700-PH or -PK relays) – For
connection between two middle poles.
Jumper – For
middle poles
700-N4
Check Out Tool — Mechanically maintains the Bulletin 700-P, -PH, or -PK relay in the
energized position for troubleshooting purposes.
1
700-N23
Check Out Tool
Cat. No. 700-N23
Adapter Plate — Simplified relay conversion. Allows you to use the existing mounting
holes when you replace a Bulletin 700-B, -BR, -BX, or -D relay with a Bulletin 700-P, -
PH, or -PK relay.
700-N34
Protective Cover –— For 700-PT Timing Adjustment Knob. Helps prevent tampering
with time setting.
5
700-N38
IP 2x Finger-Safe Cover Accessories
Description Pkg. Quantity Cat. No.
Top Covers (Covering Top Level Contact Screws)
IP2X Top Cover for 700-P, (AC Standard Relays) 5 700-PFSACT
IP2X Top Cover for 700-P, (DC Standard Relays) 5
700-PFSDCT
IP2X Top Cover for 700PK, (AC Master Control Relays) 5
700-PFSAPKT
IP2X Top Cover for 700PK, (DC Master Control Relays) 5
700-PFSDPKT
Timer Top Cover Kit, (for Relays with Pneumatic Latch Attachment) 5
700-PFSTC
Timer Top Cover Kit (for Relays with Mechanical Latch Attachment) 5
700-PFSLCK
Timer Top Cover Kit, (for Master Cont. Relays with Pneumatic Timer) 5
700-PFSKTC
Latch Top Cover Kit (for Master Cont. Relays with Mechanical Latch) 5
700-PFSKLCK
Deck Covers (Covering all terminals not on top deck, only for multi-deck relays)
IP2X Deck Cover for all AC & DC Relays in the 700P Range 10
700-PFSDEK
Coil Covers
IP2X Coil Cover for all AC Relays in the 700P Range 5
700-PFSACC
IP2X Coil Cover for all DC Relays in the 700P Range 5
700-PFSDCC