Instruction manual

Bulletin 700-CF
IEC Industrial Control Relays
9-155
Specifications
0
1
2
3
4
5
6
7
8
9
10
11
12
13
Control Circuit General
Cat. No. 700-CF
Rated Insulation Voltage U
i
IEC 690V
UL; CSA 600V
Rated Impulse StrengthU
imp
6 kV
High Test Voltage
1 minute (per IEC 60947-4)
2500V
Rated Voltage U
e
AC 115, 230, 400, 500, 690V
DC 24, 48, 110, 220, 440V
Short-Circuit Protection gG Fuse 10 A
Rated Frequency 50/60 Hz, DC
Ambient Temperature
Storage –55…+80 °C (–67…176 °F)
Operation at nominal current –25…+60 °C (–13…140 °F)
15% current reduction
for AC-12 at > 60 °C
–25…+70 °C (–13…158 °F)
Corrosion Resistance
humid-alternating climate, cyclic,
per IEC 60068-2-30 and
DIN 50 016, 56 cycles
Altitude
2000 m above mean sea level, per
IEC60 947-4
Type of Protection
IP2X (IEC 60529 and DIN 40050) in connected state
Shock Resistance
IEC 60068-2: Half sinusoidal shock
11 ms, 30 G (in 3 directions)
Vibration Resistance
IEC 60068-2: Static >2 G, in normal
position no malfunction <5 G
Verification of Making and Breaking Capacities of Switching Elements Under Normal Conditions
Corresponding to the Utilization Categories
Utilization
Category
Normal Condition of Use
Make‡ Break‡
Number and Rate of Making and Breaking
operations
I / I
e
U/U
e
cos ψ
I / I
e
U/U
e
cos ψ
No. operating
cycles§
Operating cycles per
minute
ON time [s]
®
AC-12
1 1 0.9 1 1 0.9 6050 6 0.05
AC-13
2 1 0.65 1 1 0.65 6050 6 0.05
AC-14
6 1 0.3 1 1 0.3 6050 6 0.05
AC-15
10 1 0.3 1 1 0.3 6050 6 0.05
DC
— —
T
0.95
——
T
0.95
———
DC-12 1 1 1 ms 1 1 1 ms 6050 6 0.05
®
DC-13 1 1
6 x P♣
11
6 x P♣
6050 6 0.05
®
DC-14
10 1 15 ms 1 1 15 ms 6050 — 0.05
®
I
e
Rated operational current, I Current to be made or broken
U
e
Rated operational voltage, U Voltage before make
PU
e
I
e
Steady-state power consumption (W)
T
0.95
Time to reach 95% of the steady-state current (ms)
 See sub-clause 8.3.3.5.2.
‡ For tolerances on test quantities, see sub-clause 8.3.2.2.
§ The first 50 operating cycles shall be run at U/U
e
=1.1 with the loads set at U
e
.
♣ The value “6 x P” r
esults from an empirical relationship which is found to represent most DC magnetic loads to an upper limit of P = 50 W, e.g., 6 x P= 300 W.
® The ON time shall be at least equal to T
0.95
.
 Where the break current differs from the make current value, the ON time refers to the make current value after which the current is r
educed to the break
current value for a suitable period e.g., 0.05 s.
Utilization Category Table from EN 60947-5-1
Cat. No. 700-CF
Operating Voltage
AC 50/60 Hz
Pickup
[x U
s
]
0.85…1.1
Dropout
[x U
s
]
0.3…0.6
DC
1
Pickup
[x U
s
]
0.8…1.1
Dropout
[x U
s
]
0.1…0.6
Coil Consumption
AC 50/60 Hz
Inrush [VA/W] 70/50
Seal [VA/W] 8/2.6
DC (conventional) Inrush/Seal [W] 6.5
DC (electronic)
Inrush (avg./
peak)
[W] 10/17
Seal [W] 1.7
Operating Times
AC 50/60 Hz
Pickup Time [ms] 15…30
Dropout Time [ms] 10…60
DC (conventional)
Pickup Time [ms] 40…70
Dropout Time [ms] 7…15
DC (electronic)
Pickup Time [ms] 25…50
Dropout Time [ms] 25…50
Min OFF time [ms] 200
Max. ripple ± 15%
Latch Attachment Release, 100-FL
Coil Consumption
AC [VA/W] 45/40
DC [W] 25
Contact Signal Duration [min./max] 0.03…15 s
Timing Attachment
Reset Time, 100-
ETA, 100-ETB
at min. time
setting
[ms] 10
at max. time
setting
[ms] 70
Repeat Accuracy ± 10%
1 For 9V DC, code ZR, use operating voltage 0.65…1.3 x U
s
.
For 24V DC, code ZJ, DJ, or EJ use operating voltage 0.7…1.25 x U
s
.
For 110V DC, code ED use operating voltage 0.7…1.25 x U
s
.
www.ab.com/catalogs Preferred availability cat. nos. are b
bold
.
Publication A117-CA001A-EN-P