Instruction manual
Bulletin 700-HL
Interposing/Isolation Relays
9-52
www.ab.com/catalogs Preferred availability cat. nos. are b
bold
.
Publication A117-CA001A-EN-P
Specifications
0
1
2
3
4
5
6
7
8
9
10
11
12
13
Cat. No. 700-HLT…2-Pole (Relay Output)
Electrical Ratings
Rated Thermal Current (
I
th
)
2-Pole — 10 A
Rated Insulation Voltage (U
i
)
250V IEC, 300V UL/CSA
Contacts
Inductive V AC
UL
120V AC
AC-15, 3.0A
B 300, 3.0 A
1/4 HP (186 W), 1-phase
240V AC
AC-15, 3.0 A
B 300, 1.5 A
1/2 HP (373 W), 1-phase
Inductive V
DC
24V DC DC-13, 2.0 A
125V DC DC-13, 0.3 A
250V DC DC-13, 0.2 A
Resistive
Make, Break
and
Continuous
250V AC 10 A
24V DC 10 A
250V DC 0.28 A
Min. Permissible Contact Ratings 12V, 10 mA (120 mW) for Silver Contacts, 5V, 1 mA (50 mW) for Gold Contacts
Permissible Coil Voltage Variation
Pickup: 85…110% of Nominal Voltage at 50 Hz
85…110% of Nominal Voltage at 60 Hz
80…110% of Nominal Voltage at DC
Must Dropout
Voltage:
10% of
Nominal
Voltage at AC
5% of
Nominal
Voltage at DC
Design Specification/Test Requirements
Dielectric Withstand Voltage
Pole to Pole
(VRMS)
1000V
Contact to
Coil
(VRMS)
5000V
Adjacent
Contacts
(VRMS)
2500V
Input Voltage 12V AC/DC 24V AC/DC 48V DC 120V AC/DC 240V AC/DC
Impedance (Ohms)
Power Consumption
±10%
1 K 2 K 3 K 34 K 72 K
AC N/A 0.5V A N/A 0.4V A 0.8V A
DC 0.4 W0.5 W0.8 W0.5 W0.7 W
Mechanical
Degree of Protection IP20
Mechanical Life Operations 3 x 10
7
Electrical Life Operations
250V AC/24V DC, 8 A Resistive: 100 000 min.
24V DC, 10 A Resistive: 6000 min.
250V DC, 0.28 A Resistive: 6000 min.
250V AC, 10 A Resistive: 30 000 min.
Switching Frequency Operations (no-load) 1200 cycles/sec
Coil Voltages See Overview/Product Selection
Operating Time at Nominal Voltage at 20 °C (ms)
Pickup typical 10 ms
Dropout typical 10 ms
Maximum Operating Rate (full load = 6 A) 6 cycles/min.
Environmental
Temperature
Operating –40…+60 °C
Storage –40…+100 °C
Altitude 2000 m (6560 ft)
Construction
Insulating Material Molded High-Dielectric Material
Enclosure Relay RT II — flux-proof, pollution degree 2 installation environment
Contact Material AgNi 90/10 or AgNi 90/10 + Au
Terminal Markings on Socket In accordance with EN50 0005
Certifications cULus Listed (File No. E3125, Guide NRNT/NRNT7), CE Marked
Standards UL 508, CSA C22.2 No. 14, EN/IEC 60947-1, -5-1
1 Performance Data – See this catalog, Important 3