Instruction manual

Bulletin 700-HP
Interposing/Isolation Relays
9-59
www.ab.com/catalogs Preferred availability cat. nos. are b
bold
.
Publication A117-CA001A-EN-P
Accessories
0
1
2
3
4
5
6
7
8
9
10
11
12
13
Accessories
Description Pkg. Quantity Cat. No.
Diode Surge Suppressor
Voltage Range: 6…220V DC used with 700-HN123 socket
10
700-ADR
Diode with LED Surge Suppressor
Voltage Range: 6…24V DC used with 700-HN123 socket
10
700-ADL1R
Diode with LED Surge Suppressor
Voltage Range: 28…60V DC used with 700-HN123 socket
10
700-ADL2R
Diode with LED Surge Suppressor
Voltage Range: 110…220V DC used with 700-HN123 socket
10
700-ADL3R
Diode with LED Surge Suppressor
Voltage Range: 6…24V AC used with 700-HN123 socket
10
700-AV1R
Varistor with LED Surge Suppressor
Voltage Range: 110…240V AC
used with 700-HN123 socket
10
700-AV3R
RC Surge Suppressor
Voltage Range: 6…24V AC/DC used with 700-HN123 socket
10
700-AR1
RC Surge Suppressor
Voltage Range: 110…240V AC/DC used with 700-HN123 socket
10
700-AR2
Timing Module
On-Delay or One-Shot selectable voltage
range: 12…24V AC/DC used with sockets
that accept plug-in accessory modules.
t
U (A1/A2)
LED & R
t
U (A1/A2)
LED & R
On-Delay
One-Shot
1
700-AT3
Timing Module
On-Delay or One-Shot selectable voltage
range: 110…125V AC used with sockets
that accept plug-in accessory modules.
700-AT3A1
Timing Module
On-Delay or One-Shot selectable voltage
range: 230…240V AC used with sockets
that accept plug-in accessory modules.
700-AT3A2
Screw Terminal Socket — Panel or DIN Rail Mounting
8-pin miniature socket for use with 2-pole, Bulletin 700-HP relays. Incorporates coil and contact
separation.
10
700-HN123
Cat. No. 700-HN123
8-Way Jumper can be cut to required length. Rated 10 A – 250V 1
Color Cat. No.
Red 700-HN180R
Gray 700-HN180G
Cat. No. 700-HN180 Blue 700-HN180B
Cat. No. 700-HN119
Plastic Retainer and Ejection Lever
For use with the 700-HN123 sockets
Built-in ability to accept 1492 snap-in markers
10
700-HN119
Cat. No. 700-HN230
Spring Clamp Terminal Socket — Panel or DIN Rail Mounting
8-pin miniature socket for use with 2-pole, Bulletin 700-HP relays. Incorporates coil and contact
separation.
10 700-HN230
Cat. No. 700-HN232
Plastic Retainer and Ejection Lever
For use with the 700-HN230 sockets
Built-in ability to accept 1492 snap-in markers
10
700-HN232
DIN (#3) symmetrical hat rail
35 x 7.5 x 1 m
10
199-DR1
Cat. No. 199-DR1
Relay Identification Snap-in Markers
Note - These markers can only be used when the Plastic Retainer and Ejection Lever accessory
(part # 700-HN119) is used because the markers snap into the Ejection Lever (and not into the
relay itself).
5
1492-MS5X12
5 1492-MS6X9
5 1492-MS6X12
5
1492-MS8X9
5
1492-MS8X12
100
1492-MP-Blank
Snap-in markers
Pre-Printed Identification Tags — contains 10 sheets of pre-printed and blank tags. Each sheet
contains 13 sets of the markings CR…9CR, TR…9TR, M…9M, F, R, 1S, and 117 blank tags. Tags
are peel-off with sticky backing for easy placement on relays.
10
700-N40
700-N41