User Manual

ManualsBrandsSiemens ManualsBuilding automationChipcard holder with doorbell speaker HCH3.2/..

333

HOTEL SOLUTION™

Chipcard holder with

doorbell speaker

HCH3.2/..

Chipcard holder to register room occupancy status

• Registers access code on chipcard

• Transfers access code to room controller

• Membrane switches for signals from hotel room

• Built-in optical display of messages from hotel room

• Messages indicated by LEDs above imprinted symbols

• Illuminated card slot for guidance when entering hotel room

• Built-in speaker for 3-tone chimes (doorbell feature)

Application

The HCH3.2 chipcard holder is used in conjunction with the HRC3.1 and HRC3.2 room

controllers. Guest and hotel-staff access codes are read by the HCH3.2 chipcard holder

and transmitted to the HRC3.1/HRC3.2 room controller for access control. The

HRC3.1/ HRC3.2 room controller activates the pre-programmed occupancy-dependent

room functions in the hotel room in accordance with the room occupancy status

(guest(s) in room, hotel staff in room, or room empty).

CM2N6333en

01.09.2008

Building Technologies

Summary of content (8 pages)

PAGE 1
s 6 333 HOTEL SOLUTION™ Chipcard holder with doorbell speaker HCH3.2/.. Chipcard holder to register room occupancy status • Registers access code on chipcard • Transfers access code to room controller • Membrane switches for signals from hotel room • Built-in optical display of messages from hotel room • Messages indicated by LEDs above imprinted symbols • Illuminated card slot for guidance when entering hotel room • Built-in speaker for 3-tone chimes (doorbell feature) Application The HCH3.
PAGE 2
Function The HCH3.2 chipcard holder communicates with the HRC3.1/HRC3.2 room controller via a serial port, performing the following functions: • Reads the access code on a chipcard • After reading it, transmits the access code to HRC3.1/HRC3.2 room controller • Activates the functions programmed in the HRC3.1/HRC3.2 room controller based on the access code concerned (guest code, hotel staff code, invalid code).
PAGE 3
Mechanical design Construction The chipcard holder consists of: • Component assembly (carrier, printed circuit board, four LEDs, membrane switches, chipcard reader-unit, terminal block and DIP switch) • Base frame − Bticino Living/Type L4703 for HCH3.2/BB − Bticino Light/Type N4703 for HCH3.2/BW − Vimar Idea/Type 16713 for HCH3.2/VB − Vimar Plana or Ikon/Type 20613 for HCH3.2/VW The component assembly is permanently glued into the base frame and cannot, therefore, be replaced.
PAGE 4
Rear view RS485- 3 DC 12 V 4 6333Z02de RS485+ 2 5 1 EKULIT LSM-S3OK 8ohm 2W DC 0 V 4 ON ADR0 ADR1 PROT TERM 3 Key STOP Important note 3 4 Speaker DIP switches 5 Terminal block • Bus address setting (ADR0, ADR1) • Protocol setting − PROT = 0, for HRC3.1/HRC3.2 room controller − PROT = 1, for HRC3.
PAGE 5
Commissioning To operate several devices connected to the same room controller, set an address for each one. Only one device operates with the factory-set default. The addresses of the room operator units are set by DIP switch on the back of these units. Bus address 0x3C 0x3D 0x3E 0x3F ADR0 OFF ON OFF ON ADR1 OFF OFF ON ON Note In the standard application with only one reader, address 0x3C is used for the HCH3.2 chipcard holder. This address is preset by the manufacturer (both ADR switches to OFF).
PAGE 6
Technical data Power supply (from HRC3..
PAGE 7
Dimensions Weight HCH3.2/BB – Bticino frame L4703 HCH3.2/BW – Bticino frame N4703 HCH3.2/VB – Vimar frame 16713 HCH3.2/VW – Vimar frame 20613 (without cover; and see dimension diagrams) Excluding packaging With packaging 115 mm x 72 mm x 47 mm 115 mm x 72 mm x 47 mm 118 mm x 75 mm x 48 mm 118 mm x 75 mm x 48 mm 0.085 kg 0.103 kg 3 4 1 2 3 4 S2 1 2 3 4 Serial port, RS485+ Serial port, RS-485 – DC 12 V operating voltage DC 0 V operating voltage S2 N1 HCH3.2 chipcard holder HRC3.
PAGE 8
Dimensions HCH3.2/BB Dimensions in mm Diagram and dimensions of Bticino frame L4703. HCH3.2/VB Dimensions in mm Diagram and dimensions of Vimar frame 16713. 47 6333M01 72 115 118 111,8 48 6333M02 75 67 0,9 90,6 4 9 Note See the frame supplier documentation for dimensions of other frames and hole spacing (Bticino, Vimar). 8/8 © 2006-2008 Siemens Switzerland Ltd Building Technologies HCH3.2/.. - Chipcard holder with doorbell speaker Subject to change CM2N6333en 01.09.