User Manual

ManualsBrandsSiemens ManualsFire - LMS Management StationsHUB-4 Communication Card for NCCNT WAN, Installation Instructions

Siemens Siemens

Siemens

IndustryIndustry

Industry

Inc. Inc.

Inc.

Building Building

Building

ecec

hnologies Dihnologies Di

hnologies Di

visionvision

vision

P/N 315-099458-9

Model HUB-4

INTRODUCTION The Model HUB-4 Communication Card from Siemens Industry, Inc., mounts in the

CC-5 Card Cage and provides up to four independent data channels, which can be

wired as either Style 4 or Style 7 for communication to the remote XLS, MXL, XL3 or

other UL864 listed local fire alarm panel providing dry relay contacts that can be used

for event monitoring.

The HUB-4 consists of a single Main-2 board on which two COM-2 boards are

installed. In turn, up to two modem or RS-485 Interface blocks can be installed on

each COM-2 board. Each modem block installed provides a single FSK data channel.

Each RS-485 Interface block installed provides a proprietary RS-485 interface channel.

Either a RS-485 Interface or a Modem Block module can be used, dependent on

application. Table 1 describes the connections that can be made.

1ELBAT

SEPYTNOITCENNOCDNASLENAPERIFDNA4-BUH

LENAP584-SRMEDOM

BssalC

)4elytS(

AssalC

)7elytS(

BssalC

)4elytS(

Ass

alC

)7elytS(

3LX A/NA/NXMMXMMNAWCCN

ylno

LXM A/NA/N003-IMC003-IMC

LXM-ISF W1-MINA/NdnaM1/W1-MIN

kcolBmedoM

A/NroNAWCCN

2-I

rotartnecnoC

SLX-ISF MPR/BUHBUHBUHA/N

rehtO sOIAW

)61-1(

sOIAW

)61-1(

A/NA/NNAWCCN

ylno

Each of the four data channels is controlled by a separate micro-controller which

provides all background supervision of the data lines (to the remote panel) as well as

sending and receiving Fire Panel information to the primary micro-controller. The

information from these four channels is concentrated into a single data stream and

sent to the NCC WAN via the NIC-C or the PMI-2 Concentrator via HNET. On NCC

WAN, the HUB-4 communicates on each of four ports with either the MMX (XL3

Modem), the CMI-300 (MXL modem), NIM-1 FSI (MXL FSI modem), NIM-1W (MXL

RS-485), RPM (XLS RS-485), HUB-4 (XLS RS-485), HUB-4 (XLS modem) or up to 16

WAIO (Wide Area Input Output) boards. On the PMI-2 Concentrator, the HUB-4

communicates on each of the four ports with either the NIM-1W/NIM-1M (MXL

Modem), NIM-1W (MXL RS-485), RPM (XLS RS-485), HUB-4 (XLS RS-485), or HUB-4

(XLS modem).

Using the Modem Block module, communication distance is 8 miles (CMI-300/MMX-1)

or 10 miles (HUB-4 to HUB-4) over 18 gauge twisted pair lines depending on the quality

of the communication wires (attenuation cannot exceed -23 dBm [CMI-300/MMX-1] or

Communication Card for NCC WAN/PMI-2 Concentrator

Installation Instructions

Figure 1

HUB-4 Communication

Card

Summary of content (16 pages)

PAGE 1
Installation Instructions Model HUB-4 Communication Card for NCC WAN/PMI-2 Concentrator INTRODUCTION The Model HUB-4 Communication Card from Siemens Industry, Inc., mounts in the CC-5 Card Cage and provides up to four independent data channels, which can be wired as either Style 4 or Style 7 for communication to the remote XLS, MXL, XL3 or other UL864 listed local fire alarm panel providing dry relay contacts that can be used for event monitoring.
PAGE 2
-38dBm [HUB-4 to HUB-4] @ 2.5KHz), however, using conditioned data grade leased lines from the phone company, the distance is unlimited. Using the RS-485 Interface module, the communication distance is 12,000 feet using 18 gauge twisted pair lines. OPERATION On NCC WAN, the HUB-4 can communicate using either the CMI-300, MMX, NIM-1W/ NIM-1M or HUB-4 slave Modem supervising the data circuit as well as the connected MXL or XL3 Control Panel.
PAGE 3
that port is considered to be an unspecified, unconfigured port that has detected a modem originate signal or RS-485 data from a remote unit. GND FAULT (Yellow) Normally OFF. When illuminated, indicates that the HUB-4 has detected either a negative or positive ground fault on its field wiring. OPEN/SHORT (Yellow) Normally OFF. When consistently illuminated, the HUB4 has detected an OPEN/SHORT in either the primary or secondary wired communications line.
PAGE 4
3. HUB-4, COM-2 Board: Make sure that the jumper settings are correct for the desired application (either Modem Block or RS-485 Interface Module). Refer to Table 2 and Figure 3 for the correct placement of jumpers on P5 and P6.
PAGE 5
3. Using the three nylon spacers provided with each HUB-4, COM-2, place the screw end of the spacers through the holes in the top of the HUB-4, Main-2 board. (Refer to Figure 4, page 5.) 4. Secure the spacers in place on the underside of the HUB-4, Main-2 board with the nylon nuts provided. 5. Connect the HUB-4, COM-2 to the HUB-4, Main-2 by lining up the 2x15 connectors on the HUB-4 COM-2 to the 2x15 receptacles on the HUB-4, Main-2. Keep in mind that Port 1 is the P1 receptacle, etc.
PAGE 6
NUT SPACER SCREW TABLE 4 HUB-4 MODULE PLACEMENT Number of Channels MODEM BLOCK OR RS-485 INTERFACE MODULE PLACEMENT HUB-4 COM-2 PLACEMENT PORT 1 Place HUB-4 COM-2 on P1 of HUB-4 Main-2 Place Modem Block or RS-485 Interface Module on P1 of HUB-4 COM-2 1 2 Place HUB-4 COM-2 on P1 of HUB-4 Main-2 Place first Modem Block or RS-485 Interface Module on P1 of HUB-4 COM-2; Place second Modem Block or RS-485 Interface Module on P2 of HUB-4 COM-2 1 2 3 Place first HUB-4 COM-2 on P1 of HUB-4 Main-2; P
PAGE 7
2 1 J3 1 2 RS485 INTERFACE J2 Figure 6 RS-485 Interface Module MODEM BLOCK MODULE JUMPER SETTINGS The Modem Block module has three configuration jumpers: JP1, JP2, and JP3. Refer to Figure 7 for the location of the jumpers. Set the jumpers to the configuration shown in Table 5. Refer to the Modem Block Installation Instructions, P/N 315-099356, for further information.
PAGE 8
Verify that the DIN connectors of the card and the cardcage aligned properly. The card can only plug in one direction to the card cage, if it does not align, DO NOT FORCE the card. Place thumbs on the front panel adjacent to the captive screws and gently apply even pressure on the card until the connectors seat in the receptacles on the motherboard. Secure with the captive screws. Connect the modem or RS-485 Interface transmission lines to the correct CC-5 screw terminal connectors on the HUB-4 board.
PAGE 9
ELECTRICAL RATINGS Input Power 24V Back Plane Current Screw Terminal 24V Current 6.2V Back Plane Current 24V Standby Current Output Power Each modem Channel pair 0 400mA 30mA 400mA 2V peak-to-peak max 1.3mA max Maximum line attenuation -23dbm @ 2.5KHz 8V peak-to-peak 75mA during message transmission Each RS-485 Interface RS-485 output pair 560 OHM EOL P/N 140-988066 NOTES 1. Mount the LLM-1 within the MXL enclosure.
PAGE 10
TYPICAL CLASS A (STYLE 7) CONNECTION 3 4 TB1 2 1 2 3 4 TWO 2-WIRE 18 AWG CABLE MIN* 600 OHM MAX LINE RESISTANCE TOTAL PER PAIR MODEM 2 + 1 2 + 4 + 3 + 2 - 1 A B B A - TB2 LLM-1 - 1 (CMI-300) - MOM-4 3 4 5 6 7 8 PSC-12 9 10 11 12 13 A B B A A 14 15 16 B A RESET POWER MODULE FAIL TB2 LLM-1 1 2 3 + + 24V 4A FAIL HUNDREDS TENS ONES HNET MODEM 3 4 GND FAULT 24V 12A FAIL + *USE 2-WIRE COPPER CABLE, 105 C, 300V, 18 AWG, SOLID OR STRANDED, MAX 7 STR
PAGE 11
MMX-1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 2 3 + A B + + - 1 - B A B 4 5 6 - A - + MODEM 2 B A 7 8 PSC-12 RESET POWER 9 10 11 12 13 14 15 16 A B B A A B B A - - + MODULE FAIL CAN FAIL HNET FAIL GND FAULT 24V 12A FAIL 24V 4A FAIL + + MODEM 3 - ONES HNET - TENS + HUNDREDS MODEM 4 ONE SLOT OF CC-5 #1 WITH HUB-4 INSTALLED 17 O — 18 19 20 21 22 23 24 ON OFF BATTERY TB2 TB4 12 _ + _ + NON- POWER LIMITED OUTPUT (24VDC @ 12A Max
PAGE 12
11 10 9 8 7 6 5 4 3 2 1 TB1 120 OHMS EOLR 120 OHMS EOLR + 1 1 2 4 3 A B B + 2 A A B B 4 5 11 12 13 B B A A A 3. 200 ohms max per pair. 0.34 μF max line to line. 18 19 15 16 B A B MODEM OR RS-485 INTERFACE 4 20 Figure 12 Typical Class B (Style 4) Wiring to WAIO Connection TB1 8 ONE SLOT OF CC-2/5 WITH HUB-4 INSTALLED 17 1 7 14 + 10 + 9 MODEM OR RS-485 INTERFACE 3 2. Positive or negative ground fault detected at <25K ohms on CC5 pins 1-16.
PAGE 13
x The interface type 120 OHM EOL (For use with RS-485 only) P/N 140-049099 (Modem or RS-485) must match on each COM-2 card. If only one interface is used on a COM-2 card, it must be placed on Port #1 or Port #3 1 NCC-WAN/PMI-2 CONCENTRATOR + - A B B 1 MODEM OR OR RS-485 INTERFACE x Port #2 Port #1 + A + + - A B B * The LLM-1 inserts 10 ohms between TB1 and TB2 terminals 2 and 3 (20 ohms total).
PAGE 14
TB1 * The LLM-1 inserts 10 ohms between TB1 and TB2 terminals 2 and 3 (20 ohms total). 120 OHM EOL P/N 140-049099 x 1 The interface type (Modem or RS-485) must match on each COM-2 card.
PAGE 15
TB1 The interface type Modem or RS-485) must match on each -2 card. If only one interface is used on a COM-2 card, it must be placed on #1 or Port #3 NCC-WAN/PMI-2 CONCENTRATOR 1 MODEM OR OR RS-485 INTERFACE Port #2x 1 + - - + + - - A B B A A B B A 2 3 4 5 6 3 4. Refer to NIM-1M instructions, P/N 315-099105 configuration settings and specific wiring guidelines 5. Install the LLM-1 in the MXL enclosure. 4 6.
PAGE 16
THIS PAGE HAS BEEN LEFT INTENTIONALLY BLANK Siemens Industry, Inc.