User Manual

ManualsBrandsSiemens ManualsFire - Detectors & PeripheralsILED-HC, ILED-HW H-series Intelligent Remote Alarm Lamps, Data Sheet

Siemens Siemens

Siemens

IndustryIndustry

Industry

Inc. Inc.

Inc.

Building Building

Building

ecec

hnologies Dihnologies Di

hnologies Di

visionvision

vision

P/N 315-048637-7

Installation Instructions

Models ILED-HC and ILED-HW

Intelligent Remote Lamps

INTRODUCTION The Models ILED-HC (round plate) and

ILED-HW (rectangular plate) Addressable

Remote Lamps from Siemens Industry,

Inc., shown in Figure 1, operate as an

additional multi-color LED indicator for a

device in the FireFinder-XLS/Desigo Fire

Safety Modular/Cerberus PRO Modular

System’s DLC or FS-250 System’s FS-DLC

loop circuit. The ILED-H can be used when

a device already has an accessory. The

ILED-H can be installed at any location of a

DLC/FS-DLC loop, and it remotely indicates

the status of the device(s) in that same loop.

Mode of Operation The ILED-H has one mode of operation: Direct Addressing Mode. The two-position

jumper P1 must be positioned to set the mode to Direct Addressing.

When set and programmed to Direct Addressing Mode, system logic and program-

ming determine when (FireFinder-XLS/Desigo Fire Safety Modular/Cerberus PRO

Modular and FS-250) and what color (FireFinder-XLS/Desigo Fire Safety Modular/

Cerberus PRO Modular only) the ILED-H will blink.

Controls and Indicators The LED indicator is capable of flashing any one of three distinct colors: green,

yellow, or red, based on logic in the Zeus Tool. The blink color (red only) cannot be

changed on the FS-250 System.

In Canada, ILED-Hs configured for Direct Addressing mode must be configured in

the Zeus Tool as follows:

hsalF

roloCegasU

deRmralA

wolleYyrosivrepuS

wolleYelbuorT

neerGlamroN

ILED-HW

ILED-HC

Figure 1

ILED-HC And ILED-HW Remote Lamps

Summary of content (4 pages)

PAGE 1
Installation Instructions Models ILED-HC and ILED-HW Intelligent Remote Lamps INTRODUCTION The Models ILED-HC (round plate) and ILED-HW (rectangular plate) Addressable Remote Lamps from Siemens Industry, Inc., shown in Figure 1, operate as an additional multi-color LED indicator for a device in the FireFinder-XLS/Desigo Fire Safety Modular/Cerberus PRO Modular System’s DLC or FS-250 System’s FS-DLC loop circuit. The ILED-H can be used when ILED-HW ILED-HC a device already has an accessory.
PAGE 2
PROGRAMMING Refer to Figure 2 for the location of the programming holes and jumper P1. PROGRAMMING HOLES TB1 ILED-H P1 1 3 Figure 2 ILED Printed Circuit Board Direct Addressing Mode To set the ILED-H to Direct Addressing Mode follow the steps listed below: 1. Determine a unique address for the ILED-H. 2. Set jumper P1 to position 2 and 3. 3.
PAGE 3
TB1 TO DLC OR FS-DLC LOOP LINE1 ILED-H LINE2 Figure 3 Wiring The ILED-H INSTALLATION Be sure to program the ILED before installing the unit. The ILED-H may be placed at any location on the DLC or FS-DLC loop. Use a singlegang switch box (user supplied) for mounting the ILED-HW. Use a 4-inch octagonal conduit box (user supplied) for mounting the ILED-HC. Refer to Figure 4 for typical ILED-H installation.
PAGE 4
Cyber security disclaimer Siemens products and solutions provide security functions to ensure the secure operation of building comfort, fire safety, security management and physical security systems. The security functions on these products and solutions are important components of a comprehensive security concept. It is, however, necessary to implement and maintain a comprehensive, state-of-the-art security concept that is customized to individual security needs.