Installation Instructions

ManualsBrandsSiemens ManualsFire - Detectors & PeripheralsILED-XC EPD

Table Of Contents

FCC Statement

A6V101055484_en--_a Siemens Industry, Inc.

Building Technologies Division

INSTALLATION INSTRUCTIONS

Models ILED-XC and ILED-XW

Intelligent Remote Lamps with Dual Isolators

INTRODUCTION

The Models ILED-XC (round plate), P/N S54370-B6-A1, and ILED-XW (rectangular plate), P/N

S54370-B5-A1, Addressable Remote Lamps from Siemens Industry, Inc., shown in Figure 1. It

operates as an additional tri-color LED indicator for a device in the device loop circuit of the Desigo

FC2025/FC2050/FV2025/FV2050 and Cerberus PRO FC922/FC924/FV922/FV924 Fire Alarm

Systems. The ILED-X can be used when a device already has an accessory. The ILED-X can be

installed at any location of a device loop, and it remotely indicates the status of the device(s) in that

same loop.

ILED-XW

ILED-XC

Figure 1

ILED-XC and ILED-XW Remote Lamps

MODE OF OPERATION

The ILED-X must have a unique address when it works in the device loop.

The ILED-X modules support two operation modes: polarity insensitive mode and isolator mode. The

modules can be wired for either mode (refer to Figures 3 and 4). During the isolator mode, the built-in

dual isolators will work at both sides of the module to isolate the line short in front or behind the module.

CONTROLS AND INDICATORS

The LED indicator is capable of flashing any one of three distinct colors: green, yellow, or red, based on

logic in the system configuration tool.

Observe precautions for handling Electrostatic Sensitive Devices.

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Models ILED-XC and ILED-XW Intelligent Remote Lamps with Dual Isolators INTRODUCTION The Models ILED-XC (round plate), P/N S54370-B6-A1, and ILED-XW (rectangular plate), P/N S54370-B5-A1, Addressable Remote Lamps from Siemens Industry, Inc., shown in Figure 1. It operates as an additional tri-color LED indicator for a device in the device loop circuit of the Desigo FC2025/FC2050/FV2025/FV2050 and Cerberus PRO FC922/FC924/FV922/FV924 Fire Alarm Systems.
PAGE 2
NOTE: The system logic and programming determine when and what color the ILED-X will blink: Flash Color Condition Flash Intervals (Seconds) Green Normal supervisory operation 10 Amber Device is in trouble 4 Alarm 1 No power or need to be replaced - Red No Flashes PROGRAMMING Refer to Figure 2 for the location of the programming holes: PROGRAMMING HOLES ARE POLARITY INSENSITIVE - PLUG CAN BE INSERTED IN ANY DIRECTION.
PAGE 3
To program the ILED-X, follow the steps listed below: 1. Determine a unique address for the ILED-X. 2. Connect the ILED-X to the DPU Device Programming Unit by inserting the plug from the DPU cable provided with the DPU into the programming holes on the ILED-X board at either direction (polarity insensitive). 3. Follow the instructions in the DPU Manual, P/N 315-033260, to program the ILED-X to the desired address. Record the device address on the label located on the back of the ILED-X front panel. 4.
PAGE 4
TO NEXT ADDRESSABLE DEVICE 5 LINE LINE + 6 T O C O N T R O L PA N E L OR PREVIOUS ADDRESSABLE DEVICE LINE - 1b LINE + PROGRAMMING HOLES Figure 4 ILED-X isolator mode wiring NOTES: 1. In the device line, up to 30 of any compatible devices in polarity insensitive mode with 20 ohms max line resistance can be isolated between two modules in isolator mode in a Class A Style 6 wiring. 2.
PAGE 5
The number of ILED-X modules on the device loop must be included in the total count of intelligent field devices. For the restriction of the total number of devices in the device loop, refer to the device loop circuit of the Desigo FC2025/FC2050/FV2025/FV2050 and Cerberus PRO FC922/FC924/FV922/FV924 Fire Alarm Systems. ELECTRICAL RATINGS Operating Voltage 13 – 32 Vdc 500µA Max.
PAGE 6
Cyber security disclaimer Siemens products and solutions provide security functions to ensure the secure operation of building comfort, fire safety, security management and physical security systems. The security functions on these products and solutions are important components of a comprehensive security concept. It is, however, necessary to implement and maintain a comprehensive, state-of-the-art security concept that is customized to individual security needs.
PAGE 7
FCC Statement WARNING! Installation and usage of equipment not in accordance with instructions manual may result in: Radiation of radio frequency energy Interference to radio communications • Install and use equipment in accordance with instructions manual • Read the following information This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, may cause interference to radio communications.
PAGE 8
THIS PAGE HAS BEEN LEFT INTENTIONALLY BLANK. Siemens Industry, Inc. Building Technologies Division Florham Park, NJ Siemens Canada, Ltd.