Fume Hood Sash Open Area Module (SOAM) Application 2955: 2 to 9 Combination Sash Bench Mounted Configuration Start-up Procedures Building Technologies A6V10801615 07.06.
Table of Contents Before You Begin ..................................................................................................3 Verifying Power .........................................................................................................3 Installing USB Driver .................................................................................................3 Verifying Slave Mode Application ..............................................................................
Before You Begin Verifying Power Before You Begin WARNING A fume hood is a safety device. Anyone attempting to start up a Fume Hood Controller and its related equipment must have completed Operations Training. WARNING DO NOT connect to the USB port of the SOAM while the fume hood is in operation. At the job site, locate the major control system and the mechanical and electrical drawings. This should include any components working in conjunction with the Sash Open Area Module (SOAM).
Before You Begin Setting Controller Address Setting Controller Address 1. If using the sensor bus to communicate the face area: Verify CTLR ADDRESS is correct (default is 51 and does not need to be changed). Setting the Application 1. Select the desired application.
Before You Begin Fume Hood Specific Sash Setup and Calibration Sash Setup 2955 1. Set REPORT to OVERVIEW. Two and Four Combination Sash Configurations. Nine Combination Sash Configuration. NOTE: Numbers on the sashes show how the sash is wired. After the physical sashes are calibrated, the position of the sashes will display in POS SASH 1, POS SASH 2, and so on. 2. Determine the number of horizontal sash panels. Set HZ PANEL CNT to this value. 3. Measure the width of the vertical sash in inches (cm).
Before You Begin Fume Hood Specific Sash Setup and Calibration Top Frame Measurement with Air Foil Removed. 7. Measure the height of the top frame of the sash in inches (cm). The sash frame holds the horizontal sash panels and occupies the outer edges of the fume hood opening. Set TOP FRAME to this measured value. Vertical Sash Fume Hood with Bypass Area Open and Closed. 8. Open the sash until the top edge of the vertical sash is aligned with the top edge of the bypass area, closing the bypass area.
Before You Begin Fume Hood Specific Sash Setup and Calibration Example Combination Sash Fume Hood with Fixed Area. Sash Calibration NOTE: The full travel of the sash must be used during calibration. NOTE: It is recommended that the vertical sash be calibrated before the horizontal sashes. 1. Set CAL SASH NUM to 1. 2. Verify CAL SASH LOC is set to MIN. 3. Slide vertical sash 1 to the closed position.
Before You Begin Fume Hood Specific Sash Setup and Calibration Sash Panel Measurement (15-inch Sash Panels). 8. Verify CAL SASH LOC is set to MAX. 9. Slide the sash panel to be calibrated to the far right. Measure the distance from the left end of the track to the left edge of the sash panel. Set CAL SASH POS to this value. When the sash aggregator accepts the reading, the maximum position value will be entered into POS SASH 2. 10.
Before You Begin Setting External Face Area Input Setting External Face Area Input Skip this section if you are only using one SOAM, leave values at default. AI can be set up as an input for external face area. 1. Set MAX EXT AREA to the area corresponding to 10 volts from the input signal source. The next step allows the minimum voltage to bet set to a value other than 1 (default). The minimum voltage is represented when the face area is equal to 0. 2.
Before You Begin Flashing Controller Firmware Flashing Controller Firmware WCIS Procedure 1. Connect to the USB port of the SOAM. 2. From the Device menu, select Load TEC Firmware. The Load TEC Firmware dialog box displays. 3. Click the Browse button. 4. Browse to the folder where the new firmware is saved. 5. Double-click the firmware file and then click Load. 10 | 11 Siemens Industry, Inc. A6V10801615 Restricted 07.06.
Issued by Siemens Industry, Inc. Building Technologies Division 1000 Deerfield Pkwy Buffalo Grove IL 60089 +1 847-215-1000 © Siemens Industry, Inc., 2016 Technical specifications and availability subject to change without notice. Document ID: A6V10801615 Edition: 07.06.
