Extractor hood siemens-home.
en Table of contents INSTRUCTION MANUAL.......................................................... 2 sno i t cur t sen I rof 8 Intended use................................................................... 2 ( Important safety information ........................................ 2 7 Environmental protection ............................................. 4 Ç Operating modes ........................................................... 4 1 Operating the appliance..............................................
Important safety information Always ensure adequate fresh air in the room if the appliance is being operated in exhaust air mode at the same time as room airdependent heat-producing appliance is being operated. Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air through an exhaust gas system (e.g. a chimney).
en Environmental protection : Warning Risk of electric shock! ■ A defective appliance may cause electric shock. Never switch on a defective appliance. Unplug the appliance from the mains or switch off the circuit breaker in the fuse box. Contact the after-sales service. Risk of electric shock!are dangerous. Repairs ■ Incorrect repairs may only be carried out and damaged power cables replaced by one of our trained after-sales technicians.
Operating the appliance 1Operating the appliance These instructions apply to several appliance variants. It is possible that individual features are described which do not apply to your appliance. ecna i l p a eh t gn i t arepO en Lighting The lighting can be switched on and off independently of the fan. Press the A button. Setting the brightness Note: Switch on the extractor hood when you start cooking and switch it off again several minutes after you have finished cooking.
en Operating the appliance Control panel model 2 Saturation display Control panel When the metal mesh grease filters or the activated carbon filter are saturated, a signal sounds for approx. 4 seconds after the fan is switched off.
Operating the appliance Setting the fan Switching on the appliance ■ ■ Press the # button. The fan starts at setting ƒ. Press the + or - button to change the fan strength. Lighting The lighting can be switched on and off independently of the fan. Press the A button. Setting the brightness Switching off Press and hold the A button until the desired brightness is reached. Press the # button.
en Cleaning and maintenance 2Cleaning and maintenance : Warning ecnane t n i am dna gn i nae lC Risk of burns! The appliance will become hot during operation, especially near the bulbs. Allow the appliance to cool down before cleaning. Area Glass : Warning Operating controls Risk of electric shock! Penetrating moisture may result in an electric shock. Clean the appliance using a damp cloth only. Before cleaning, pull out the mains plug or switch off the circuit breaker in the fuse box.
Trouble shooting Removing metal grease filter 1. Open the lock and fold down the metal grease filter. While doing this, place the other hand under the metal grease filter. 2. Take the metal grease filter out of the holder. Malfunction table Problem The appliance does not work Possible cause The plug is not plugged in. Power cut Faulty fuse For edge extraction filters, pull the metal grease filter downwards. While doing this, place the other hand under the metal grease filter.
en Customer service 4Customer service Basic equipment: Starter set for circulating-air mode wide When calling us, please give the product number (E no.) and the production number (FD no.) so that we can provide you with the correct advice. The rating plate with these numbers can be found inside the appliance (remove the metal mesh grease filter to gain access).
Important safety information en INSTALLATION INSTRUCTIONS (Important safety information Installation instructions PLQ PP PD[ PP PLQ PP PP PLQ PP ! PP ! PP Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.
en Important safety information : Warning Room air-dependent heat-producing appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or water heaters) obtain combustion air from the room in which they are installed and discharge the exhaust gases into the open air through an exhaust gas system (e.g. a chimney).
General information en KGeneral information Electrical connection Exhaust air mode Risk of electric shock! Components inside the appliance may have sharp edges. These may damage the connecting cable. Do not kink or pinch the connecting cable during installation. no i t amro f n i l areneG : Warning Risk of death! Risk of poisoning from flue gases that are drawn back in.
en Installation 5Installation Preparing the installation no i t a l a t s n I Caution! Ensure that there are no electric wires, gas or water pipes in the area where holes are to be made. Installation 1. Screw on the fixing bracket for the flue duct. ¨ $ 1. Mark a vertical centre line on the wall from the ceiling to the lower edge of the extractor hood. 2. Mark positions for the screws and the contour of the attachment area. 3.
Installation Attaching and aligning the appliance Connecting the pipes 1. First, remove the protective foil from the back of the Note: If using an aluminium pipe, smooth the connection area beforehand. appliance and, following installation, remove the foil completely. 2. When attaching the appliance, ensure that it engages firmly with the brackets. « 3. Align the appliance horizontally by turning the brackets. If required, the appliance can be moved to the right or left.
BSH Hausgeräte GmbH Carl-Wery-Straße 34, 81739 München, GERMANY siemens-home.