Installation Instructions

ManualsBrandsSiemens ManualsControl rangesGamma Lighting Control Enclosures Installation Instructions

Document No. A6V10425806

September 10, 2014

Gamma Lighting Control Enclosures

Item Number A6V10425806, Rev. AA

Page 1 of 6

Product Description

The Siemens Industry Gamma Lighting Control

Enclosures support Gamma Lighting system

components and other panel-mounted devices that

snap into DIN rails. A Data Rail 190/32 (with

integrated connector, 324 mm) (5WG1 190-8AB32),

which is sold separately, distributes KNX bus power

and communications to 17 module widths (MW) of N-

System devices that only have a data rail connector.

A removable dead front holds a removable/reversible

door with documentation pouch.

Table 1: Gamma Lighting Enclosure Dimensions.

LCC-2020-

LCC-2028-

LCC-2044-MV

Height

20" (51 cm)

28" (71 cm)

44" (112 cm)

Width

20" (51 cm)

Depth

4" (10 cm)

DIN Rails

Each DIN rail accommodates 20 MW (Gamma N-system

module widths). 1 MW = 0.71" (18 mm).

The top DIN rail in each enclosure is commonly reserved for

low-voltage modules. If no low voltage modules exist in the

enclosure, the top DIN rail may be used for line voltage

modules.

Product Numbers

LCC-2020-MV

Gamma Lighting Control 20" (51 cm)

Enclosure

LCC-2028-MV

Gamma Lighting Control 28" (71 cm)

Enclosure

LCC-2044-MV

Gamma Lighting Control 44" (112

cm) Enclosure

Warning/Caution Notations

WARNING

Serious injury, death, or severe equipment

damage could occur if a procedure or

instruction is not followed as specified.

AVERTISSEMENT

Le non respect d'une procédure ou

instruction peut provoquer des blessures

graves voir mortelles ou endommager

l'équipement.

CAUTION

Minor or moderate injury may occur if a

procedure or instruction is not followed as

specified.

ATTENTION

Le non respect d'une procédure ou

instruction peut provoquer des blessures

mineures ou modérés.

NOTICE

Equipment damage may occur if a

procedure or instruction is not followed as

specified.

REMARQUE

Le non respect d'une procédure ou

instruction peut provoquer endommager

l'équipement.

Expected Installation Time

30 minutes

Summary of content (6 pages)

PAGE 1
Installation Instructions Document No. A6V10425806 September 10, 2014 Gamma Lighting Control Enclosures Product Description Warning/Caution Notations The Siemens Industry Gamma Lighting Control Enclosures support Gamma Lighting system components and other panel-mounted devices that snap into DIN rails.
PAGE 2
Document No. A6V10425806 Installation Instructions September 10, 2014 Required Tools and Materials Installation  Electric drill  Punch  Hammer  Level  Marker  1/8" blade screwdriver  Tape measure  Four corrosion resistant 1/4-20 bolts, flat washers and nuts To mount on concrete or masonry:  Hammer drill  Carbide-tipped masonry bit  Four 1/4-20 corrosion resistant wall anchors CAUTION Always refer to local codes or the local authorities having jurisdiction before proceeding.
PAGE 3
Document No. A6V10425806 Installation Instructions September 10, 2014 Positioning the Enclosure 1. Determine the mounting location of the enclosure using the following spacing requirements and Figure 1. - - Space between the face of the panel and an obstruction in front of the panel must be at least 11 inches (28 cm) to allow for door removal at 40 degrees. To fully open the door, a clear space of at least 28 inches (71 cm) is required from a wall on the hinged side.
PAGE 4
Document No. A6V10425806 Installation Instructions September 10, 2014 Figure 2: Enclosure Knockout Locations. Page 4 of 6 Siemens Industry, Inc.
PAGE 5
Document No. A6V10425806 Installation Instructions September 10, 2014 Wiring and Module Installation WARNING De-energize Class 1 circuits, tag and lockout the breaker panel. AVERTISSEMENT Mettre les circuits de Classe 1 hors tension, étiqueter et cadenasser le disjoncteur. Figure 3: Reversing the Enclosure Door. 1. De-energize Class 1 circuits, tag and lockout the breaker panel. 10. Place the panel layout sheet in the label pouch inside the door. 2. Run conduit and pull wires into the panel. 11.
PAGE 6
Document No. A6V10425806 Installation Instructions September 10, 2014 Figure 4: Enclosure Dimensions and Module Placement. Figure 5: Using the Wire Barrier to Maintain Class 1 and Class 2 Wire Separation. Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as design improvements are introduced. APOGEE and Insight are registered trademarks of Siemens Industry, Inc.