Installation Instructions

ManualsBrandsSiemens Manuals3rd party integrationMAXIOM Series Lighting Panels, Point Map

Document No. 565-961

March 1, 2008

Lumisys Driver

These install

ation instructions only cover the

connection o

f the Lumisys Driver to the Lumisys

system. For h

ardware installation of the Modular

Equipment Co

ntroller, see document number

565-570. For

hardware installation of th e Pow er

Open Proces

sor, see document number 565-571.

Product Des

cription

The Lumisys Driver enables communication between

the APOGEE

Automation System and the Lumisys

system.

Product Numbers

986-86398 A

Lumisys Driver, Open

Processor with RS-485

ALN

986-86398 B

Lumisys Driver, Open

Processor with Ethernet

ALN

986-86398C Lumisys Driver, MEC with

RS-485 ALN, 8D I, 8DO,

8AI, 8AO, point expansion

support, HOA-ready

986-86398 D

Lumisys Driver, MEC with

RS-485 ALN, 8D I, 8DO,

8AI, 8AO, point expansion

support, with HOA

986-86398 E

Lumisys Driver, MEC with

RS-485 ALN, 8D I, 8DO,

8AI, 8AO, point expansion

support, modem, HOA-ready

986-86398 F

Lumisys

Driver, MEC with

RS-485 A

LN,8DI,8DO,

8AI, 8AO

, point expansion

support

, modem, with HOA

986-86398G Lumisys Driver, MEC with

Ethernet ALN, 8DI, 8DO,

8AI, 8AO, point expansion

support, HOA-rea dy

986-86398H

Lumisys D river, MEC with

Ethernet ALN, 8DI, 8DO,

8AI, 8AO, p oin t expansion

support, with HOA

986-86398L

Lumisys D riv

er, M EC with

BACnet/IP AL

N, 8DI, 8DO,

8AI, 8AO, poi

nt expansion

support, HO A

-ready

986-86398M

Lumisys D river, MEC with

BACnet/IP ALN, 8DI, 8DO,

8AI, 8AO, p oin t expansion

support, with HOA

986-86398N

Lumisys Driver, Open

Processor with BACnet/IP

ALN

Warning/Caution Notations

WARNING:

Personal injury/loss of life may occur if you

do not follow the procedures as speciﬁed.

CAUTION:

Equipment damage or loss of data may

occur if you do not follow the procedures

as speciﬁed.

Expected Installation Times

7 minutes.

Required Tools and Materials

• Flat-blade screwdriver (1/8-inch blade width).

• Wire strippers.

• Cabling and connectors. See the Connecting

the Lumisy s Driver to the Lumisys System

section.

tem Number: 565-961, Rev. FA

age 1 of 4

Summary of content (4 pages)

PAGE 1
Installation Instructions Document No. 565-961 March 1, 2008 Lumisys Driver These installation instructions only cover the connection of the Lumisys Driver to the Lumisys system. For hardware installation of the Modular Equipment Controller, see document number 565-570. For hardware installation of the Power Open Processor, see document number 565-571.
PAGE 2
Document No. 565-961 Installation Instructions March 1, 2008 CAUTION: Always wear an electro-static discharge wrist strap and discharge accumulated static before touching field panel components. Prerequisites • • Depending on the type of installation, other prerequisites may have to be completed. Connecting the Lumisys Driver to the Lumisys System Follow these steps to connect the Lumisys Driver to the Lumisys system: Driver hardware is installed according to its respective installation instructions.
PAGE 3
Document No. 565-961 Installation Instructions March 1, 2008 S + DRIVER FLN 1 RS-485 TRUNK CABLE (MAX 4000’ / 1219.2 m; STANDARD 24 AWG LOW CAPACITANCE) TAPE BACK SHIELD S - RS-485 TRUNK CABLE (MAX 4000’ / 1219.
PAGE 4
Document No. 565-961 Installation Instructions March 1, 2008 Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as design improvements are introduced. Product or company names mentioned herein may be the trademarks of their respective owners. © 2008 Siemens Building Technologies, Inc. Siemens Building Technologies, Inc. 1000 Deerfield Parkway Buffalo Grove, IL 60089-4513 U.S.A. Your feedback is important to us.