Installation Instructions

ManualsBrandsSiemens Manuals3rd party integrationModbus Driver, Technical Specification Sheet

Document No. 565-887

October 27, 2006

Modbus Driver and Modbus 250 Driver

These install

ation instructions cover the connection

of the Modbus

Driver and Modbus 250 Driver to the

vendor syste

m only. F or hardware installation of the

Modular Equi

pment Controller, see document number

565-570. For

hardware installation of the Power

Open Proces

sor, see document number 565-571.

Product Des

cription

The driver enables communication between the

APOGEE

Automation System and the vendor

system.

Product Numbers

Modbus Driver

986-90392 A

Modbus Driver, Open

Processor with RS-485

ALN

986-90392 B

Modbus Dri

ver, Open

Processo

r with Ethernet

ALN

986-90392C Modbus Driver, MEC with

RS-485 ALN, 8DI, 8DO,

8AI, 8AO, point expansion

support, HOA-ready

986-90392 D

Modbus Driver, MEC with

RS-485 ALN, 8DI, 8DO,

8AI, 8AO, point expansion

support, with HOA

986-903

92E

Modbus Driver, MEC with

RS-485 ALN, 8DI, 8DO,

8AI, 8AO, point expansion

support, modem, HOA-ready

986-90392 F

Modbus Driver, MEC with

RS-485 ALN, 8DI, 8DO,

8AI, 8AO, point expansion

support, modem, with HOA

986-90392G Modbus Driver, MEC with

Ethernet ALN, 8DI, 8DO,

8AI, 8AO, point expansion

support, HOA-ready

986-90392H

Modbus Driver, MEC w ith

Ethernet ALN, 8DI, 8DO,

8AI, 8AO, point expansion

support, with HOA

986-90392L

Modbus Drive

r, MEC with

BACnet/IP AL

N, 8DI, 8DO,

8AI, 8AO, poi

nt expansi on

support, HOA

-ready

986-90392M

Modbus Driver, MEC w ith

BACnet/IP ALN, 8DI, 8DO,

8AI, 8AO, point expansion

support, with HOA

986-90392N

Modbus Driver, Op en

Processor with BAC net/IP

ALN

Modbus 250 Driver

986-90399A

Modbus 250 Driver, Open

Processor with RS-485 ALN

986-90399B

Modbus 250 Driver, Open

Processor with Ethernet ALN

986-90399C Modbus 250 Driver, MEC

with RS-485 ALN, 8DI, 8DO,

8AI, 8AO, point expansion

support, HOA-ready

986-90399D

Modbus 250 Driver, MEC

with RS-485 ALN, 8DI, 8DO,

8AI, 8AO, point expansion

support, with HOA

986-90399E

Modbus 250 Driver, MEC

with RS-485 ALN, 8DI, 8DO,

8AI, 8AO, point expansion

support, modem, HOA-ready

986-90399F

Modbus 25

0Driver,MEC

with RS-4

85 ALN, 8DI, 8DO,

8AI, 8AO

, point expansion

support

, mo dem, with HOA

986-90399G Modbus 250 Driver, MEC

with Ethernet ALN, 8DI, 8DO,

8AI, 8AO, point expansion

support, HOA-ready

tem Number: 565-887, Rev. DA

age 1 of 6

Summary of content (6 pages)

PAGE 1
Installation Instructions Document No. 565-887 October 27, 2006 Modbus Driver and Modbus 250 Driver These installation instructions cover the connection of the Modbus Driver and Modbus 250 Driver to the vendor system only. For hardware installation of the Modular Equipment Controller, see document number 565-570. For hardware installation of the Power Open Processor, see document number 565-571.
PAGE 2
Document No. 565-887 Installation Instructions October 27, 2006 986-90399H Modbus 250 Driver, MEC with Ethernet ALN, 8DI, 8DO, 8AI, 8AO, point expansion support, with HOA 986-90399L Modbus 250 Driver, MEC with BACnet/IP ALN, 8DI, 8DO, 8AI, 8AO, point expansion support, with HOA 986-90399N Modbus 250 Driver, Open Processor with BACnet/IP ALN Accessories 538-670 Trunk Interface II, 115V. 538-675 Trunk Interface II, 230V. 538-755 Trunk/RS-422 Interface, 115V. 538-760 Trunk/RS-422 Interface, 230V.
PAGE 3
Document No. 565-887 Installation Instructions October 27, 2006 S + FLN DRIVER RS-485 TRUNK CABLE (MAX 4000’ / 1219.2 m; STANDARD 24 AWG LOW CAPACITANCE) GROUND WIRE TO EARTH (P/N 538-583) POWER PACK POWER S + TAPE BACK SHIELD TXTX+ RXRX+ TRUNK / RS-422 INTERFACE PMD TERMINAL BLOCK ONE TWISTED PAIR (STANDARD 24 AWG LOW CAPACITANCE) MAX LENGTH 4000’ MODBUS DEVICE(S) GW0277R3 RXRX+ TXTX+ Figure 1.
PAGE 4
Document No. 565-887 Installation Instructions October 27, 2006 S + DRIVER FLN RS-485 TRUNK CABLE (MAX 4000’ / 1219.2 m; STANDARD 24 AWG LOW CAPACITANCE) GROUND WIRE TO EARTH (P/N 538-583) POWER PACK POWER TRUNK INTERFACE II S + PMD RX TX 7 RS-232 PORT (25-PIN FEMALE) TAPE BACK SHIELD IF DRIVER IS LESS THAN 50 CABLE FEET (15.24 m) FROM MODBUS DEVICE PLACE TRUNK INTERFACE II IN MBC ENCLOSURE 3 CONDUCTOR (MAX 50’ / 15.
PAGE 5
Document No. 565-887 Installation Instructions October 27, 2006 S + FLN DRIVER RS-485 TRUNK CABLE (MAX 4000’ / 1219.2 m; STANDARD 24 AWG LOW CAPACITANCE) ONE TWISTED PAIR TAPE BACK SHIELD S + TERMINAL BLOCK MODBUS DEVICE(S) GW1042R2 IF APPLICABLE Figure 3. TO ADDITIONAL MODBUS DEVICES Direct Connect the Driver to the Vendor’s Modbus Master or Modbus Slave Device. Siemens Building Technologies, Inc.
PAGE 6
Document No. 565-887 Installation Instructions October 27, 2006 Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as design improvements are introduced. Product or company names mentioned herein may be the trademarks of their respective owners. © 2006 Siemens Building Technologies, Inc. Siemens Building Technologies, Inc. 1000 Deerfield Parkway Buffalo Grove, IL 60089-4513 U.S.A. Your feedback is important to us.