Installation Instructions

ManualsBrandsSiemens Manuals3rd party integrationTrane Driver on the PXC Modular Platform, Technical Specification Sheet

Document No. 565-981

June 1, 2007

Trane Enhanced 2000 Driver

These installation instructions only cover the

connection of the Trane Enhanced 2000 Driver to

the Trane system. For hardware installation of the

Modular Equipment Controller, see document number

565-570. For hardware installation of the Power

Open Processor, see document number 565-571.

Product Description

The Trane Enhanced 2000 Driver enables

communication between the APOGEE

Automation

System and the Trane system.

Product Numbers

986-84303A Trane Enhanced 2000 Driver,

Open Processor with RS-485

ALN

986-84303B Trane Enhanced 2000 Driver,

Open Processor with Ethernet

ALN

986-84303C

Trane Enhanced 2000

Driver, MEC with RS-485

ALN, 8DI, 8DO, 8AI, 8AO,

point expansion support,

HOA-ready

986-84303D Trane Enhanced 2000 Driver,

MEC with RS-485 ALN,

8DI, 8DO, 8AI, 8AO, point

expansion support, with HOA

986-84303E Trane Enhanced 2000 Driver,

MEC with RS-485 ALN,

8DI, 8DO, 8AI, 8AO, point

expansion support, modem,

HOA-ready

986-84303F Trane Enhanced 2000 Driver,

MEC with RS-485 ALN,

8DI, 8DO, 8AI, 8AO, point

expansion support, modem,

with HOA

986-84303G

Trane Enhanced 2000

Driver, MEC with Ethernet

ALN, 8DI, 8DO, 8AI, 8AO,

point expansion support,

HOA-ready

986-84303H Trane Enhanced 2000 Driver,

MEC with Ethernet ALN,

8DI, 8DO, 8AI, 8AO, point

expansion support, with HOA

986-84303L Trane Enhanced 2000

Driver, MEC with BACnet/IP

ALN, 8DI, 8DO, 8AI, 8AO,

point expansion support,

HOA-ready

986-84303M Trane Enhanced 2000 Driver,

MEC with BACnet/IP ALN,

8DI, 8DO, 8AI, 8AO, point

expansion support, with HOA

986-84303N Trane Enhanced 2000

Driver, Open Processor with

BACnet/IP ALN

Accessories

538-670

unk Interface II, 115V

538-675

Trunk Interface II, 230V

Warning/Caution Notations

WARNING:

Personal injury/loss of life may occur if you

do not follow the procedures as speciﬁed.

CAUTION:

Equipment damage or loss of data may

occur if you do not follow the procedures

as speciﬁed.

Expected Installation Times

30 minutes.

tem Number: 565-981, Rev. EA

age 1 of 4

Summary of content (4 pages)

PAGE 1
Installation Instructions Document No. 565-981 June 1, 2007 Trane Enhanced 2000 Driver These installation instructions only cover the connection of the Trane Enhanced 2000 Driver to the Trane system. For hardware installation of the Modular Equipment Controller, see document number 565-570. For hardware installation of the Power Open Processor, see document number 565-571.
PAGE 2
Document No. 565-981 Installation Instructions June 1, 2007 Required Tools and Materials • Flat-blade screwdriver (1/8-inch blade width). • Wire strippers. • Cabling and connectors. See the Connecting the Trane Enhanced 2000 Driver to the Trane System section. CAUTION: Always wear an electro-static discharge wrist strap and discharge accumulated static before touching ﬁeld panel components.
PAGE 3
Document No. 565-981 Installation Instructions June 1, 2007 S + DRIVER FLN RS-485 TRUNK CABLE (MAX 4000’ / 1219.2 m; STANDARD 24 AWG LOW CAPACITANCE) GROUND WIRE TO EARTH (P/N 538-583) POWER PACK POWER TRUNK INTERFACE II S + BLN 2 3 7 RS-232 PORT (25-PIN FEMALE) TAPE BACK SHIELD IF DRIVER IS LESS THAN 50 CABLE FEET (15.24 m) FROM BCU PANEL, PLACE TRUNK INTERFACE II IN MBC ENCLOSURE RS-232 CABLE (MAX 50’ / 15.24 m) TRANE TRACER SUMMIT BCU PANEL *STANDARD RS-232 9-PIN PC PORT MALE.
PAGE 4
Document No. 565-981 Installation Instructions June 1, 2007 S + DRIVER FLN RS-485 TRUNK CABLE (MAX 4000’ / 1219.2 m; STANDARD 24 AWG LOW CAPACITANCE) GROUND WIRE TO EARTH (P/N 538-583) POWER PACK POWER TRUNK INTERFACE II S + BLN 2 3 7 RS-232 PORT (25-PIN FEMALE) TAPE BACK SHIELD IF DRIVER IS LESS THAN 50 CABLE FEET (15.24 m) FROM BCU PANEL, PLACE TRUNK INTERFACE II IN MBC ENCLOSURE RS-232 CABLE (MAX 50’ / 15.24 m) TRANE TRACER SUMMIT BCU PANEL *STANDARD RS-232 25-PIN PC PORT MALE.