Installation Instructions

ManualsBrandsSiemens Manuals3rd party integrationRT Sunline Rooftop Unit, Point Map

Document No. 565-548

November 15, 2006

YORK ISN Enhan

ced Driver

These installation instructions only cover the

connection of the YORK ISN Enhanced Driver to

the YORK system. For hardware installation of the

Modular Equipment Controller, see document number

565-570. For hardware installation of the Power

Open Processor, see document number 565-571.

Product Description

The YORK ISN Enhanced Driver enables

communication between the APOGEE

Automation

System and the YORK system.

Product Numbers

986-84360 A

YORK ISN Enhanced Driver,

Open Processo r with RS-485

ALN

986-84360 B

RK ISN Enhanced Driver,

en Processor with Ethernet

986-84360C YORK ISN Enhanced

Driver, MEC with RS-485

ALN, 8DI, 8DO, 8AI, 8AO,

point expansion support,

HOA-ready

986-84360 D

YORK ISN Enhanced Driver,

MEC with RS-485 ALN,

8DI, 8DO, 8AI, 8AO, point

expansion support, with HOA

6-84360E

YORK ISN Enhanced Driver,

MEC with RS-485 ALN,

8DI, 8DO, 8AI, 8AO, point

expansion support, modem,

HOA-ready

986-84360 F

YORK ISN Enhanced Driver,

MEC with RS-485 ALN,

8DI, 8DO, 8AI, 8AO, point

expansion support, modem,

with HOA

986-84360G YORK ISN Enhanced Driver,

MEC with Etherne t ALN,

8DI, 8DO, 8AI, 8AO,

point expansion support,

HOA-ready

986-8

4360H

YORK ISN Enhanced Driver,

MEC with Ethernet ALN,

8DI, 8DO, 8AI, 8AO, point

expansion support, w ith HOA

986-84360L

YORK ISN Enhanced Driver,

MEC with BACnet/IP ALN,

8DI, 8DO, 8AI, 8AO,

point expansion support,

HOA-ready

986-84360M

YORK ISN Enhanced Driver,

MEC with BACnet/IP ALN,

8DI, 8DO, 8AI, 8AO, point

expansion support, w ith HOA

986-84360N

YORK

ISN Enhanced

Driv

er, Open Processor

with

BACnet/IP ALN

Accessories

538-670

Trunk Interface II, 115V

538-675

Trunk Interface II, 230V

Warning/Caution Notations

WARNING:

Personal injury/loss of life may occur if you

do not follow the procedures as speciﬁed.

CAUTION:

Equipment damage or loss of data may

occur if you do not follow the procedures

as speciﬁed.

Expected Installation Times

30 minutes.

Required Tools and Materials

• Flat-blade screwdriver (1/8-inch blade width).

• Wire strippers.

tem Number: 565-548, Rev. AA

age 1 of 4

Summary of content (4 pages)

PAGE 1
Installation Instructions Document No. 565-548 November 15, 2006 YORK ISN Enhanced Driver These installation instructions only cover the connection of the YORK ISN Enhanced Driver to the YORK system. For hardware installation of the Modular Equipment Controller, see document number 565-570. For hardware installation of the Power Open Processor, see document number 565-571.
PAGE 2
Document No. 565-548 Installation Instructions November 15, 2006 • Cabling and connectors. See the Connecting the YORK ISN Enhanced Driver to the YORK System section. CAUTION: Always wear an electro-static discharge wrist strap and discharge accumulated static before touching field panel components. Prerequisites Depending on the type of installation, other prerequisites may have to be completed.
PAGE 3
Document No. 565-548 Installation Instructions November 15, 2006 S + DRIVER FLN 1 RS-485 TRUNK CABLE (MAX 3500’ / 1066.8 m; STANDARD 24 AWG LOW CAPACITANCE) GROUND WIRE TO EARTH (P/N 538-583) POWER PACK POWER TRUNK INTERFACE II S + ALN 2 3 7 RS-232 PORT (25-PIN FEMALE) TAPE BACK SHIELD IF OPEN PROCESSOR IS LESS THAN 50 CABLE FEET (15.24 m) FROM ISN PANEL, PLACE TRUNK INTERFACE II IN MBC ENCLOSURE RS-232 CABLE (MAX 50’ / 15.
PAGE 4
Document No. 565-548 Installation Instructions November 15, 2006 Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as design improvements are introduced. Product or company names mentioned herein may be the trademarks of their respective owners. © 2007 Siemens Building Technologies, Inc. Siemens Building Technologies, Inc. 1000 Deerfield Parkway Buffalo Grove, IL 60089-4513 U.S.A. Your feedback is important to us.