User Manual

Index
C-737
© Siemens AG 2008 - 2013 All Rights Reserved
SINAMICS G120 CU230P-2 Control Units List Manual (LH9), 01/2013
Function diagrams, signals and monitoring
functions
Load monitoring, 2-633
Monitoring functions 1, 2-637
Overview, 2-629
Speed signals 1, 2-630
Speed signals 2, 2-631
Thermal monitoring, motor, 2-635
Thermal monitoring, power unit, 2-634
Thermal motor models, 2-636
Torque signals, motor locked/stalled,
2-632
Function diagrams, technology controller
Closed-loop control, 2-627
Fixed value selection binary (p2216 = 2),
2-624
Fixed value selection direct (p2216 = 1),
2-625
Motorized potentiometer, 2-626
Function diagrams, technology functions
Bypass, 2-599
Cascade control, 2-600
DC braking (p0300 = 1), 2-595
Energy-saving mode, 2-601
Essential service mode (ESM), 2-598
Free technology controller 0, 1, 2, 2-596
Multi-zone control, 2-597
Function diagrams, vector control
Current setpoint filter, 2-588
Current/power/torque limits
, 2-587
Display signals, 2-593
Field weakening characteristic, Id setpoint
(ASM, p0300 = 1), 2-590
Field weakening controller, flux controller
(ASM, p0300 = 1), 2-591
Flux controller configuration, 2-585
Interface to the Power Module
(ASM, p0300 = 1), 2-592
Iq and Id controllers, 2-589
Kp_n/Tn_n adaptation, 2-578
Pre-control balancing, acceleration mod-
el, 2-576
Resonance damping and slip compensa-
tion (V/f), 2-582
Speed control configuration, 2-584
Speed controller with/without encoder,
2-577
Speed setpoint, droop, 2-575
Torque setpoint, 2-579
Upper/lower torque limit, 2-586
V/f characteristic and voltage boost, 2-581
Vdc_max controller and Vdc_min control-
ler, 2-580
Vdc_max controller and Vdc_min control-
ler (PM230/PM240), (V/f), 2-583
Fxxxx, 3-654
G
General
about parameters, 1-8
on faults and alarms, 3-650
on function diagrams, 2-497
I
IASC, 3-652
Index
Parameter, 1-9
Index (parameters), 1-17
Input/output terminals, 2-506
Analog input 2 (AI 2), 2-510
Analog inputs, 2-506
Analog inputs 0 ... 1 (AI 0 ... AI 1), 2-509
Analog outputs 0 ... 1 (AO 0 ... AO 1),
2-512
Digital inputs, 2-506
Temperature evaluation LG-
Ni1000/PT1000 (AI3), 2-513
Internal control words, 2-546
Internal control/status words, 2-546
J
Jogging, 2-564, 2-569
L
Linked parameter, 1-9
List
Abbreviations, B-725
ASCII table, A-724
Binector inputs (BI parameters), 1-475
Binector outputs (BO parameters), 1-480
Command data sets, 1-466
Connector inputs (CI parameters), 1-478
Connector outputs (CO parameters),
1-482
Connector/binector outputs (CO/BO pa-
rameters), 1-486
Drive data sets, 1-468
Fault and alarm messages, 3-659
Message ranges, 3-659
Motor data sets, 1-473
Parameter ranges, 1-19
Parameters for quick commissioning,
1-489
Parameters for write protection and know-
how protection, 1-487