User Manual

ManualsBrandsSiemens ManualsToolsService tool OCI700.1

CE1N5655en

2018-03-15

Building Technologies

655

As of ACS790 V9.00

Service tool

OCI700.1

Service case with software and service interface

The service tool consists of one service case with the ACS790 software included

on a CD ROM as well as the OCI700 service interface and 3 connecting cables

specific to the devices.

The software and service interface allow for commissioning and servicing KNX

and LPB/BSB devices.

Use

Commissioning and service of:

· KNX devices

- Synco

200 devices

- Synco

700 control and room devices

- Synco

living central apartment units

- RXB../RXL.. room controllers

- RDF../RDU../RDG.. room thermostats

- VAV compact controllers GDB../GLB..

- KNX central communications units OZW7..

· LPB/BSB devices

- Sigmagyr/Albatros control and room units

- LPB/BSB central communication units OZW6../OCI6..

Summary of content (6 pages)

PAGE 1
5 655 As of ACS790 V9.00 OCI700.1 Service tool Service case with software and service interface The service tool consists of one service case with the ACS790 software included on a CD ROM as well as the OCI700 service interface and 3 connecting cables specific to the devices. The software and service interface allow for commissioning and servicing KNX and LPB/BSB devices.
PAGE 2
Functions ACS790 software The ACS790 software commissions and services KNX and LPB/BSB devices and plants via the "ACS tool" program together with the OCI700 service interface. User view (user level) Administration Administrator or service technician have access to all data points to commission and service the plants. Plant engineering and commissioning Device search Searching for all devices connected to the bus and synchronizing with the offline device list, if created previously.
PAGE 3
Documentation Document title Document type and number Engineering and service software ACS790 Data sheet N5649 Technical design Basic design The OCI700 service interface consists of one plastic housing with 2 LEDs and 3 interface sockets. LED indication The 2 LEDs, labeled "USB" and "BUS", indicate the operational state. LED USB LED lit LED flashes Service interface with USB interface is connected to the PC/laptop. Data is being exchanged between service interface and PC/laptop.
PAGE 4
Communication connections Select connection In ACS790, select the associated connection to communicate with the devices, i.e. "OCI700-KNX" or "OCI700-LPB". OCI700 service interface and USB hubs Only 1 OCI700 service interface can be connected to a PC/laptop. The OCI700 service interface can be operated via USB hubs. General notes Mounting The OCI700 is designed for portable use. Power supply The OCI700 service interface does not require separate supply.
PAGE 5
Requirements for PC/laptop with ACS790 Processor RAM Hard disk Monitor Interfaces Operating system Drive Minimum requirements 1 GHz 1 GB 2 GB for installation. Additional space required for plant data SVGA standard driver 1024 × 768, 256 colors · USB 1.1 and higher Serial COM to 19,200 baud · Network card (Ethernet) ® ® · Microsoft Windows 7 from Service Pack 1, 32- and 64-bit versions ® ® · Microsoft Windows 8, 32- and 64-bit versions ® · Microsoft DotNet Framework 4.
PAGE 6
Connections The following pin assignments of the KNX and LPB/BSB plugs on the OCI700 service interface apply to assembly of own connection cables: 1234567 8 Pin assignment LPB/BSB, RJ12 1 2 3 4 5 6 5655Z03 5655Z02 Pin assignment KNX, RJ45 1 2 3 4 5 6 7 8 CE+, Konnex CE–, Konnex Unused Unused Voltage 16 V Transmission line to RLU2.. Receiving line: RLU2..