SIMATIC Industrial PC SIMATIC Panel PC 877 Operating Instructions Edition 07/2006 Industrial PC Panel PC 877 simatic DOCUMENTATION
SIMATIC Industrial PC SIMATIC Panel PC 877 Operating instructions Release 07/2006 A5E00877780-01 Foreword 1 Safety information 2 Description 3 Application planning 4 Installation 5 Connecting 6 Integration into an automation system 7 Commissioning 8 Operation and configuration 9 Operation 10 Functions 11 Maintenance and service 12 Alarm, error and system messages 13 Troubleshooting/FAQs 14 Technical data 15 Dimension drawings 16 Detailed descriptions 17 Appendix A ESD d
Safety Guidelines This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. Danger indicates that death or severe personal injury will result if proper precautions are not taken.
Table of contents 1 Foreword ................................................................................................................................................ 1-1 1.1 2 3 4 5 6 Overview .................................................................................................................................... 1-1 Safety information................................................................................................................................... 2-3 2.
Table of contents 7 8 9 10 iv Integration into an automation system .................................................................................................... 7-1 7.1 Overview .................................................................................................................................... 7-1 7.2 7.2.1 7.2.2 Device in a SIMATIC S7 configuration....................................................................................... 7-2 MPI/PROFIBUS-DP network.............
Table of contents 11 12 13 Functions .............................................................................................................................................. 11-1 11.1 Overview .................................................................................................................................. 11-1 11.2 Safecard on Motherboard (SOM)............................................................................................. 11-2 11.3 Temperature monitoring........
Table of contents 14 15 16 17 vi Troubleshooting/FAQs.......................................................................................................................... 14-1 14.1 General problems..................................................................................................................... 14-1 14.2 Problems when Using Modules of Third-party Manufacturers................................................. 14-2 14.3 Temperature limits ....................................
Table of contents A B Appendix.................................................................................................................................................A-1 A.1 A.1.1 A.1.2 A.1.3 Certificates and guidelines......................................................................................................... A-1 Guidelines and declarations....................................................................................................... A-1 Certificates and approvals ........
Table of contents viii SIMATIC Panel PC 877 Operating instructions, Release 07/2006, A5E00877780-01
1 Foreword 1.1 1.1 Overview Purpose of the manual These operating instructions contain all the information you need for commissioning and using the SIMATIC Panel PC 877. It is intended both for programming and testing personnel who commission the device and connect it with other units (automation systems, programming devices), as well as for service and maintenance personnel who install add-ons or carry out fault/error analyses.
Foreword 1.1 Overview Position in the information landscape The documentation for the Panel PC includes the following sections: • SIMATIC Panel PC 877, Operating Instructions (compact) with the following information: – Commissioning – Legal information • SIMATIC Panel PC 877, Operating Instructions The documentation is supplied with the Panel PC in electronic form as a PDF file on the "Documentation and Drivers" CD. The documentation is available in German, English, French, Italian and Spanish.
Foreword 2.1 Safety information Safety information 2.1 2.1 2 Safety information Warning Emergencies In the event of a device fault, interrupt the power supply immediately. Inform the customer service personnel responsible. Malfunctions can occur when the operator controls or power cable are damaged or when liquids or foreign objects penetrate the device.
Foreword 2.1 Safety information Electrical connection Warning Disconnect the device from the mains before every intervention. Do not touch power lines or data transmission lines during electrical storms and do not connect any cables. System expansions Only install system expansion devices designed for this device. If you install other expansions, you may damage the system or violate the safety requirements and regulations for radio frequency interference suppression.
Foreword 2.1 Safety information Handling and disposal of lithium batteries Warning Danger of explosion and the release of harmful substances! Do not throw lithium batteries into fire, do not solder onto the cell body, do not open, do not short circuit, do not reverse pole, do not heat above 100 °C, dispose of according to regulations, and protect from direct sunlight, moisture and condensation. Replace lithium batteries with the same brand or a brand recommended by the manufacturer.
Foreword 2.2 General information 2.2 2.2 General information Overview Caution The device is approved for operation in closed rooms only. The guarantee is void if this stipulation is ignored. Avoid extreme environmental operating conditions. Protect your device against dust, moisture and heat. For additional information, refer to the Technical data. Do not place the device in direct sunlight. Transport Unpack the device at its installation location. Transport the device only in the original packaging.
Foreword 2.2 General information Tools & downloads Please check regularly if updates and hotfixes are available for download to your device. Downloads are available on the Internet at http://www.siemens.com/asis under "Support". Click on "Software Tools & Downloads" on "Overview Panel PCs" Using the global search function, you can then also search for any downloads you require.
Foreword 2.2 General information Sources of light Notice Position the screen so that it is not subject to direct sunlight or other strong sources of light. Defective pixels in the display At present, the manufacturing process of modern displays does not guarantee that all pixels of the display will be perfect. A small number of defective pixels in the display is therefore unavoidable. This does not present a functional problem as long as the defective pixels are not bunched in one location.
3 Description 3.1 3.1 Design Design Figure 3-1 Panel PC 877 1 Computer unit 2 Control unit Brief description The device is available with different control units which are distinguished by the size of the display and by the membrane keyboard or touch screen.
Description 3.1 Design Keyboard variants • Color display with backlighting: – 12'' TFT technology with 800 x 600 resolution – 15'' TFT technology with 1024 x 768 resolution • Membrane keyboard with alphanumeric keys, numeric keys, cursor keys and control keys • Function keys and softkeys • Integrated mouse • LEDs for power supply, temperature, softkeys, and keys • Front-mounted USB 2.0 interface for connecting external I/O devices.
Description 3.2 Technical features 3.2 3.2 Technical features General features 2x PCI long 2x PCI/ISA shared long 1x ISA long Note: The RAID1 option takes one PCI slot.
Description 3.2 Technical features Configuration options Power supply • • Processor • • • 100V/240V AC, 360 W; wide range; with bridgin brief power failures in accordance with NAMUR: maximum 20 ms at 0.85 x Un (Un = rated voltage) 24 V DC, 265 VA, optional, only in connection with Intel ® Pentium Mobile Intel ® Celeron 2 GHz, 400 MHz Front Side Bus FSB, 1024 Kbytes Second Level Cache Intel ® Pentium 4 2.8 GHz, 533 MHz Front Side Bus FSB, 512 Kbytes Second Level Cache Intel ® Pentium 4 Mobile 2.
Description 3.3 Accessories 3.3 3.3 Accessories The accessories comprise the following components: Accessories Comment Order No.
Description 3.
Application planning 4.1 4.1 4 Overview Introduction This section describes the first steps after unpackaging, the permitted mounting positions and the fixation. This section describes the necessary considerations for EMC. Field of application The Panel PC is an industry-standard PC platform for demanding tasks in the field of PCbased automation.
Application planning 4.2 Unpacking and checking the delivery 4.2 4.2 Unpacking and checking the delivery Procedure 1. Please check the packaging material for transport damage upon delivery. 2. If any transport damage is present at the time of delivery, lodge a complaint at the shipping company in charge. Have the shipper confirm the transport damage immediately. 3. Unpack the device. Caution Do not lie the device on its back. This will avoid any damage to an optical drive which may be present.
Application planning 4.3 Device identification data 4.3 4.3 Device identification data Procedure 1. Write down the Microsoft Windows Product Key of the Certificate of Authenticity COA in the table at the end of this section. The COA label is only present in preinstalled Windows 2000 Professional or XP Professional and is affixed to the back of the device. You will need the product key during the reinstallation of the operating system. Figure 4-1 COA label, example 2.
Application planning 4.4 Mounting Positions and Fastening 4.4 4.4.1 4.4 Mounting Positions and Fastening Installation guidelines Before installing the device, read the following general notes relating to installation. Warning Danger, high voltage Isolate the power supply to the switchgear cabinet before opening it. Ensure that the power to the switchgear cabinet cannot be turned on accidentally. Caution The device is approved for operation in closed rooms only.
Application planning 4.4 Mounting Positions and Fastening Note The computer unit with AC power supply satisfies fire protection requirements to EN60950-1. It may therefore be installed without additional fire-proofing measures. • Provide adequate volume in the switchgear cabinet for air circulation and heat transport. Keep at least 10 cm distance between the device and switchgear cabinet.
Application planning 4.4 Mounting Positions and Fastening 4.4.2 Permitted mounting positions Approval Certain mounting positions are approved for the equipment that comprises one control unit and one computer unit. Permitted mounting positions r r Vertical installation with deviations between +20° and -20° in the given directions is permissible.
Application planning 4.4 Mounting Positions and Fastening 4.4.3 Type of fixation The computer unit is secured in the mounting cut-out either with clamps or screws. Select the type of fixation suitable to your requirements for the degree of protection (see Section Protection against dust and water) .
Application planning 4.4 Mounting Positions and Fastening 4.4.4 Protection against dust and water Principle The degree of protection provided at the front is assured when the mounting seal lies completely against the mounting cut-out. Caution Please ensure that the material strength at the mounting cut-out is a maximum of 6 mm. Please follow the specifications for the dimensions in the "Mounting cut-out" section.
Application planning 4.5 Mounting cut-out 4.5 4.5 4.5.1 Mounting cut-out Preparing the mounting cut-out The following illustration show the dimensions for the mounting cut-out.
Application planning 4.5 Mounting cut-out Table 4-1 Dimensions for the mounting cut-out in mm Control unit L1 L2 L3 1) L4 1) L5 L6 2) L7 2) L8 2) L9 2) A1 A2 S1 S2 S3 S4 S53) Tolerance +1 +1 ±0.2 ±0.5 ±0.5 ±0.5 ±0.
Application planning 4.5 Mounting cut-out 4.5.2 Mounting depth of the device Panel PC with operator units T Key panel with 12" TFT 192 mm Key panel with 15" TFT 211 mm Touch panel with 15" TFT 209 mm Touch panel with 19" TFT 217 mm 7 Note Additional mounting depth with optical drive The installation depth increases by 21 mm when an optical drive is installed in the device.
Application planning 4.6 EMC directive 4.6 4.6 EMC directive Electromagnetic compatibility The device fulfills the requirements of the EMC law of the Federal Republic of Germany as well as the EMC directive of the Single European Market. The device is designed as a built-in device. You ensure compliance with the EN 61000-4-2 (ESD) EMC standard by installing the device in grounded metal cabinets (e.g. 8 MC cabinets, Siemens catalog NV21).
5 Installation 5.1 5.1 Securing the device with clamps You require 6 clamps in order to mount the device with a 12"/15" display. A device with a 19" display must be mounted with 8 clamps. The required number of clamps is included in your Panel PC delivery package. Required tool for fasting the clamps: 2.5 mm hexagonal spanner Figure 5-1 Clamp assembly Rack installation Steps for fastening the device with clamps 1 Disconnect the device from the power supply.
Installation 5.1 Securing the device with clamps IP 65 degree of protection The plant builder is responsible for the correct installation of the device. The degree of protection IP65 is only guaranteed for the front of the device if the ring seal is properly applied with the correct size of cutout, the unit has been clamped in place, and the instructions below are observed.
Installation 5.2 Securing the device with screws 5.2 5.2 Securing the device with screws Note To secure the 19" front panel with screws, backing plates with Order No. 6AV7672-8KE000AA0 are required on the front. Drilling holes Steps for drilling holes 1 Drill holes (Ø approx. 2.5 mm) from the rear in the 4 recesses of the control unit. 2 Use a Ø 5.5 mm bit for M5 and a Ø 6.
Installation 5.
Installation 5.2 Securing the device with screws IP 54 degree of protection The IP54 degree of protection is guaranteed for screw mounting together with the ring seal. Caution Observe the panel seal when mounting Ensure you do not damage the panel seal when mounting the device. Notice Control cabinet installation; Material strength at the mounting cut-out Please ensure that the material strength at the mounting cut-out is a maximum of 6 mm.
Installation 5.
6 Connecting 6.1 6.
Connecting 6.1 Connection and operator control components Reset button The Reset key can trigger the following function during active operation: Hardware reset: Immediate shutdown of the device without correct shutdown of the operating system This function is used to shut down the device when it no longer responds. This triggers a hardware reset. Press the key briefly with a pointed object. Following a hardware reset, the device automatically boots up.
Connecting 6.1 Connection and operator control components Connection components of the control unit USB connection control unit Item Name Description (1) USB 1 connection USB 2.0 high current (500 mA) under sealing flap (not available with every product variant). Notice Guarantee for the IP 65 degree of protection When the sealed cover over the USB interface is removed in order to connect a USB component, the IP 65 degree of protection for the device is no longer guaranteed.
Connecting 6.2 Connecting the 100 V to 240 V AC power supply 6.2 6.2 Connecting the 100 V to 240 V AC power supply General connection information Note the following in order to operate the device safely and according to regulation: Note Voltage range The power supply module is designed for operation on 100 to 240 V AC networks. The device adjusts automatically to the voltage. Notice Risk of damage Do not connect or disconnect power and data cables during thunderstorms.
Connecting 6.2 Connecting the 100 V to 240 V AC power supply Power Factor Correction The power supply contains an active PFC (Power Factor Correction) circuit to conform to the EMC guidelines. Uninterruptible AC power systems (UPS) must supply a sinusoidal output voltage in the normal and buffered mode when used with SIMATIC PCs with an active PFC. UPS characteristics are described and classified in the standards EN 50091-3 and IEC 62040-3.
Connecting 6.3 Connecting the 24 V DC power supply 6.3 6.3 Connecting the 24 V DC power supply General connection information Note the following in order to operate the device safely and according to regulation: Notice Power supply The device must only be connected to 24 V DC power supply systems or 24 V DC power supplies which meet the requirements of a safe extra-low voltage (SELV). Use the supplied connector to connect it to the supply voltage.
Connecting 6.4 Connecting the equipotential bonding circuit 6.4 6.4 Connecting the equipotential bonding circuit A low resistance ground connection ensures that interference signals generated by external power supply cables, signal cables or cables to the I/O modules are safely discharged to ground.
Connecting 6.
Integration into an automation system 7.1 7.1 7 Overview Introduction The following options are available for integrating the device in existing or planned system environments and networks. Ethernet The integrated Ethernet interface can be used for communication and for data exchange with automation devices such as SIMATIC S7. You require suitable software for this: STEP7, WinCC, WinCC flexible, WinAC, SIMATIC NET.
Integration into an automation system 7.2 Device in a SIMATIC S7 configuration 7.2 7.2.1 7.2 Device in a SIMATIC S7 configuration MPI/PROFIBUS-DP network You can connect the device to a SIMATIC S7 automation system or a PROFIBUS DP network via the MPI/DP interface. You can connect up to 32 PC, PG, or AS devices to one network segment. The use of repeaters allows you to interconnect several MPI/PROFIBUS DP network segments. The complete MPI/PROFIBUS DP network consists of a maximum of 127 stations.
Integration into an automation system 7.2 Device in a SIMATIC S7 configuration 7.2.
Integration into an automation system 7.3 Networking via Industrial Ethernet 7.3 7.3 Networking via Industrial Ethernet You can establish a network between the device and other computers via Industrial Ethernet. The on-board LAN is a Twisted-Pair (TP) interface for data transfer rates of 10/100 Mbit/s. The interface is Plug and Play-ready and is automatically detected in Windows. Protocol settings are made in the Windows control panel.
Commissioning 8.1 8.1 8 Overview Checklist Before starting up the device for the first time, go through the following checklist: • Have you taken into account the proper ambient and environmental conditions for the device, as described in the Technical data? • Have you learned how to connect the equipotential bonding? • Have you learned how to connect the power supply? • Read over this information in the respective "Connecting" chapter of the operating instructions. Please follow all guidelines.
Commissioning 8.2 Switch on the device 8.2 8.2 Switch on the device Procedure 1. Plug the power plug of the supplied power supply cable in the AC/DC power supply connector of the computer unit. 2. Lock the power plug in place. 3. Plug the power supply cable of the computer unit into a socket with a grounded protective conductor. 4. Switch on the computer unit at the power switch. The "POWER" LED will light up. The device starts up and boots.
Commissioning 8.3 Setting up the Microsoft Windows operating system 8.3 8.3 Setting up the Microsoft Windows operating system Introduction The setup wizard appears immediately following the startup of the device. The wizard is used to set the parameters of the operating system. Note The dialogs of the setup wizards differ slightly in some places for the Windows 2000 Professional and Windows XP Professional operating systems. In order to change to the next dialog, click on the ">>" button.
Commissioning 8.4 Installing applications and drivers 8.4 8.4 Installing applications and drivers Introduction After the device is restarted, different dialogs appear on the screen. Drivers and applications can be installed from these dialogs. Additional hardware and software components You can install and configure additional hardware and software components. For additional information, refer to the documentation of the hardware and software.
Commissioning 8.4 Installing applications and drivers Setting the touch screen This step only applies to control units with touch screen panels. 2. In the following dialog, click on the screen size that corresponds to your device. You will find details of the screen size on the rating plate for the control unit. The display resolution of the device will be adjusted correspondingly. Figure 8-2 Touch screen panel, selecting the screen size 3. Click on "Finish" to end the Panel Wizard.
Commissioning 8.4 Installing applications and drivers Figure 8-3 Touch screen panel, end Panel Wizard 4. New hardware, the touch controller, is found. In order to start the touch calibration, click on "OK". Carry out the following steps carefully: Figure 8-4 Start touch screen calibration 5. Briefly touch the touch screen at every cross hair. Continue from Point 7.
Commissioning 8.4 Installing applications and drivers Setting the key panel This section applies only to control units with key panels. 6. Click on "Finish" to end the Panel Wizard. Figure 8-5 Keyboard panel, end Panel Wizard 7. Exit the operating system session and restart the device. Otherwise the "Security features" from "KeyTools" will not be activated.
Commissioning 8.4 Installing applications and drivers The installation of the drivers and applications is complete. Further information is available in the "Operation and configuration" chapter in the section, "Additional drivers and applications." Notice After starting up your device, find out more about the particulars of the operating system in the chapter "Commissioning" in the section, "Microsoft Windows operating systems".
Commissioning 8.5 BIOS settings 8.5 8.5 BIOS settings A USB keyboard is not fully available before Windows starts up. There are not restrictions to using a USB keyboard when editing the BIOS. To be able to select a boot menu before Windows starts, however, connect a PS/2 keyboard. Caution Activate the "USB legacy Keyboard/Mouse" feature only when a USB keyboard or mouse is connected. A requirement for activation is that "USB BOOT" has been selected in the BIOS.
Commissioning 8.6 Microsoft Windows operating system 8.6 8.6.1 8.
Commissioning 8.6 Microsoft Windows operating system 8.6.2 Windows 2000 Professional Restrictions Notice If you have an external PS/2 keyboard and a USB keyboard connected at the same time, the keyboard LEDs on the external keyboards may not be correctly refreshed in some circumstances. Service pack After a new installation of Windows 2000 Professional, install at least Service Pack 4. Service Pack 4 is supplied in the product package.
Commissioning 8.6 Microsoft Windows operating system 8.6.3 Windows XP Professional Restrictions Note If you have an external PS/2 keyboard and a USB keyboard connected at the same time, the keyboard LEDs on the external keyboards may not be correctly refreshed in some circumstances. Service Pack After a new installation of Windows XP Professional, install at least Service Pack 2. Service Pack 2 is supplied in the product package.
Commissioning 8.7 USB 8.7 8.7 USB Introduction Commercially available USB peripherals can be easily and flexibly connected via the USB interface. For example, you can connect an external USB keyboard and a USB mouse. If the USB keyboard has a USB interface, you can connect other USB peripherals, such as a USB mouse, directly to the keyboard. USB interface There are several types of USB peripherals: • Low power devices: maximum 100 mA power consumption, e.g.
Commissioning 8.
Operation and configuration 9.1 9.1.1 9.1 9 Normal operation Switch on the device Requirements • The peripheral devices are connected. Caution To comply with the EMC guideline of the device with I/O, ensure that the manufacturer or supplier of the components used guarantees compliance with the regulations. Connect the I/O devices via shielded cables with metal connectors.
Operation and configuration 9.1 Normal operation Procedure Warning Danger of incorrect operations! The following applies to external input devices or combinations of external input devices and control units with key panels: Ambiguous key codes can cause serious malfunctions of the application program. Always activate the "Security features" of "KeyTools." Please note the applicable safety information in the "Operation and configuration" chapter in the section, "Additional drivers and applications.
Operation and configuration 9.1 Normal operation 9.1.2 Logging on to the operating system via the onscreen keyboard (OSK) The logon dialog is displayed when you have assigned an administrator password. Note A screen keyboard appears for devices with touch screen panels. You can enter the administrator password directly on the touch screen using the screen keyboard or using the mouse. For additional information, refer to the Microsoft help on screen keyboards.
Operation and configuration 9.1 Normal operation 9.1.3 Switching off the device Introduction To turn off the device, shut it down and disconnect the device from the power supply. Procedure 1. Exit the operating system session of the device properly. Caution When using the operating systems Windows 2000 Proofessional and Windows XP Professional, wait until the display has turned dark. 2. Switch the device off using the On/Off switch. 3.
Operation and configuration 9.2 Additional Drivers and Applications 9.2 9.2.1 9.2 Additional Drivers and Applications Overview The necessary drivers and applications are contained in the supplied "Documentation and Drivers" CD. Note The supplied drivers and applications have been system-tested and are approved for this device. No warranty can be provided for other software. Press the "Help" button to obtain information concerning the buttons of a dialog.
Operation and configuration 9.2 Additional Drivers and Applications 9.2.2 Calibrating the touch screen, UPDD Call • Start menu "Start", command "Programs > UPDD > Settings" Function Recalibrates the touch screen. If the touch screen does not react as expected when touched, repeat the calibration. To do this, first activate the 25 point calibration and then calibrate the touch screen. Figure 9-1 25-point calibration Note For further information press the "Help" button.
Operation and configuration 9.2 Additional Drivers and Applications Warning Maloperation If you touch the touch screen while the screen saver is active, the SIMATIC process visualization software, e.g. WinCC, will carry out the functions which happen to be behind it. Caution Only touch one point on the touch screen and not several points at one time. You may otherwise trigger unintended reactions.
Operation and configuration 9.2 Additional Drivers and Applications 9.2.3 Enable/disable touch functionality The procedure for deactivating and reactivating the touch functionality using the "UPDD" software is described in the table below. No. Procedure 1 Open the Control Panel menu in the Windows operating system 2 Open the properties of the "Pointer Device" application in the Control Panel to access the "Pointer Device Properties" dialog.
Operation and configuration 9.2 Additional Drivers and Applications No. Procedure 5 To start up the touch functionality again, you must mark the corresponding touch controller in the "Devices" tab and activate the option "Show inactive PnP devices". Then select the "Advanced" tab again. 6 In the "Advanced" tab, deactivate the "Enabled" option and load the settings by clicking the "Apply" button. The touch functionality is now activated again.
Operation and configuration 9.2 Additional Drivers and Applications 9.2.
Operation and configuration 9.2 Additional Drivers and Applications Alarms Click on "Change the way Security Center alerts me" to switch off security alarms upon switching on the device. The "Alert Settings" dialog appears. Deactivate the desired alarms.
Operation and configuration 9.2 Additional Drivers and Applications 9.2.5 KeyTools (for key panel devices only) SIMATIC KeyTools is one selection of the applications for your Panel PC. These applications allow you to adapt key codes that are sent by the key panel of the control unit.
Operation and configuration 9.2 Additional Drivers and Applications 9.2.6 Screen keyboard (for touch panel device only) You can operate the device by means of a virtual screen keyboard. You can use it to enter the characters directly on the touch screen or with an externally connected mouse. Calling up TouchInput Call up the "TouchInput" application on the desktop. The screen keyboard is displayed.
Operation and configuration 9.2 Additional Drivers and Applications 9.2.7 Setbrightness Start "Set brightness" symbol on the desktop. Function The intensity of the backlighting is adjusted using "Set brightness.
Operation and configuration 9.2 Additional Drivers and Applications 9.2.8 CheckLanguageID Scope The following applies to Windows 2000 Professional Multi-Language and Windows XP Professional Multi-Language. Call c:\drivers\checklang\checklangid.exe or reinstallation from the "Documentation and Drivers" CD. Function "CheckLanguageID" displays the currently installed languages.
Operation and configuration 9.2 Additional Drivers and Applications 9.2.9 Multilingual settings for the operating system Windows MultiLanguage MUI operating system enables users to set the language of the GUI to their individual preference. Some elements are not localized, however, and remain in the original language of the system - English. You should therefore always install English language service packs.
Operation and configuration 9.2 Additional Drivers and Applications Notice If you use a different keyboard layout to "Englisch/USA international", the internal keyboard codes will no longer be correct. Start > Control Panel > Date, Time, Language, and Regional Options > Add other languages > Languages tab,Language used in menus and dialogs field. For the Date, Time, Language and Regional Options set the default as non-Unicode programs under Advanced in addition to the language for menus and dialogs.
Operation and configuration 9.2 Additional Drivers and Applications 9.2.10 DVD ROM/CD RW The DVD-ROM/CD-RW drive is an optional feature. Recording methods supported by the disk drive: Disc at once, Track at once, Session at once, Packet writing, whereby Disc at once und Track at once are recommended due to their compatibility to other optical drives. DVD-ROM, CD-ROM, CD-R and Video CDs can be read.
Operation and configuration 9.2 Additional Drivers and Applications 9.2.11 USB keyboard controller The USB keyboard controller supports the following additional functions for key models: • Keyboard programming with the "KeyTools" application • Adjustment of the backlighting brightness with the application "SetBrightness." • Control of the key LEDs The USB keyboard controller must be installed before this function can be used.
Operation and configuration 9.
10 Operation 10.1 10.1 Status displays The two LEDs on the upper left hand side of the front panel display the operating status: • LED "POWER" green: Active voltage • LED "TEMP" orange: The temperature threshold has been exceeded; the maximum value is preset and cannot be changed. Refer to the "Functions" chapter for more information.
Operation 10.2 General control elements 10.2 10.2 General control elements On / Off switch On / Off switch Description The On/Off switch does not disconnect the device from supply voltage. When the switch is in 0 position (Off), the device is still connected to the auxiliary voltage. Warning The On/Off switch does not disconnect the device from supply voltage. Reset button Reset button Description The reset button can be actuated with a pin or an opened up paper clip, for example.
Operation 10.3 Device with key panel 10.3 10.3 Device with key panel The device has the following keypads: • 2 x 8 vertical keypads with softkey functions • 2 x 10 horizontal keypads with function keys F1 -F20 The number of keys, their labeling and function is the same on all key panels. The various panel types differ only in the arrangement of the keys and in the size and type of the display. The following figure is therefore only an example using the front view of the 12" variant.
Operation 10.3 Device with key panel 10.3.1 Using the keyboard The membrane keyboard is divided into different functional groups: • Function keys and softkeys with LEDs • Control keys • Alphanumeric keys • Numeric keys • Cursor keys Function keys The function keys are arranged in a double row below the display. Figure 10-2 Function keys with LEDs, taking the 15" control unit as an example Softkeys The softkeys are arranged on the left and the right of the display.
Operation 10.
Operation 10.3 Device with key panel Alphanumeric keys Enter letters, special characters, blank spaces and underline using the alphanumeric keys. Figure 10-5 Alphanumeric keys (1) Underline (2) space character Toggling between lower-case and upper-case letters Enter the lower-case letters using the pre-defined assignment of the alphanumeric keys. To enter an upper-case letter, proceed as follows: 1. Hold down the key. 2. Activate the desired alphanumeric key at the same time.
Operation 10.3 Device with key panel Numeric keys Enter the numerals "0" to "9" and special characters, e.g. the decimal point, using the predefined assignment of the numeric keys. Figure 10-6 Numeric keys Enter special characters, arithmetic signs and signs Special characters, arithmetic signs and signs are also assigned to most of the alphanumeric and numeric keys. These signs are indicated by white symbols on the top left of the keys. To enter such a sign, proceed as follows: 1.
Operation 10.3 Device with key panel Cursor keys Navigate, scroll or move the writing mark using the cursor keys. The cursor keys correspond to the usual keys of the PC keyboard.
Operation 10.3 Device with key panel External keyboards The keyboard layout has been set to "English/USA international." If you use a keyboard with a layout other than the "English/USA international" layout, the key codes of the internal and external keyboards might no longer correspond. Notice Maloperation If you activate several keys simultaneously, a malfunction on the device cannot be excluded.
Operation 10.3 Device with key panel 10.3.2 Using the direct control key module The direct control key module is a module that is intended for use with the SIMATIC Panel PC 877 (exclusively for variants with an integral membrane keyboard). Digital events can be assigned to the function keys and softkeys (F1-F20 and S1-S16) of the membrane keyboard via this module. This means that a digital input of a PLC can be activated at the press of a key over PROFIBUS.
Operation 10.3 Device with key panel Example: The keyboard codes, that are sent when any key is operated, are stored in a code table.
Operation 10.3 Device with key panel Changing the defaults The program "KeyPad.exe" can be used to assign each key individually with special key codes. The following example shows the layout of the 15" Panel PC keyboard variant after starting the relevant program for the device "keypads15.exe": Figure 10-8 KeyPad The individual key fields can be clicked to open a configuration form for the respective key.
Operation 10.3 Device with key panel Explanation: The key labelled F13 outputs the key code LSHIFT+F1 and sets digital input DI 0.0 when the direct key module is used. For further information about using the tool, visit the Internet page http://www.siemens.com/asis. Search here under "Download" using the term "Keypad". The self-unpacking file F_KEY_Total.exe contains extensive information (description in English and German, examples) on using the additional function keys of the Panel PC 877.
Operation 10.3 Device with key panel 10.3.3 Labelling function keys and softkeys Area of application This section applies only to control units with key panels. Introduction The control unit has two horizontal and two vertical keypads Assign user specific functions to the keys as needed. Label the keys with labelling strips from the options. DIN A4 film is available for the production and insertion of the labeling strips, as described in chapter 3 "Description".
Operation 10.3 Device with key panel Procedure 1. Label the DIN A4 film with a laser printer, for example, using the print format templates for MS Word on the Documentation and Drivers CD. 2. Cut the labeling strips along the pre-printed lines. Note Do not insert handwritten labeling strips until the ink has dried. 3. Insert the labeling strips into the slots provided on the rear side of the control unit.
Operation 10.3 Device with key panel 10.3.4 Using the integrated mouse The position on which you press the middle round button of the integrated mouse determines the direction in which the cursor moves. The amount of pressure determines the speed of the cursor. Alternatively to using the integrated mouse you can also connect an external mouse to the front USB port.
Operation 10.4 Device with touch screen 10.4 10.4 Device with touch screen The 15" variant and the 19" variant differ in their dimensions and the size of the display. The 19" variant has no drill hole covers on the sides. The following figure is only an example using the front view of the 15" variant.
Operation 10.4 Device with touch screen 10.4.1 Using the touch screen On the display that is touch-sensitive due to the touch sensor, application-specific user interface elements, for example buttons, are displayed. When you tap the command button with your finger, the function assigned to the button is activated. The following types of pressure are permissible: • Using a plastic pen with a 1 mm radius at the point: 25 g. • Using a silicone finger with a diameter of 1.6 cm: 50 g.
Operation 10.5 Disk drive 10.5 10.5 Disk drive Introduction The device is equipped with a 3.5" floppy drive as standard. You can use the floppy drive to save programs and data and transfer data from the floppy disk to the device. Diskette types The follows diskettes are supported: Double sided double density Double sided high density 720 KB 1.44 MB, 135 TPI Caution Data loss! Do not press the ejection button when the green access LED of the drive is lit.
Operation 10.6 Transferring authorizations 10.6 10.6 Transferring authorizations Authorizations of HMI software are provided on diskette. Transfer these, if required, from the built-in diskette drive.
11 Functions 11.1 11.1 Overview The following individual functions are implemented: • Temperature monitoring and over/under temperature indication • Watchdog • Fan monitoring Messages can be output from the monitoring modules to the applications. The SOM software (Safecard On Motherboard) and DiagMonitor software are provided on the devices for this.
Functions 11.2 Safecard on Motherboard (SOM) 11.2 11.2 Safecard on Motherboard (SOM) The "Safecard On Motherboard" software is available on the "Documentation and Drivers" CD. Before this software is installed, previously installed DiagMonitor software must be deinstalled. This application is used to monitor PC hardware (temperature, watchdog and fans) and to display the current measured values.
Functions 11.2 Safecard on Motherboard (SOM) (1) Temperature range Here the current temperature and limit values are shown. You can toggle the temperature display mode to indicate either the current temperature, or the min./max. values measured since the start of the application.
Functions 11.3 Temperature monitoring 11.3 11.3 Temperature monitoring Temperature monitoring The temperature is recorded by means of three thermocouples. One thermocouple monitors the processor temperature, another the temperature in the area near the processor module, and a third the temperature in the area of the disk drives.
Functions 11.4 Watchdog (WD) 11.4 11.4 Watchdog (WD) Function The watchdog monitors the program execution and reports a program crash to the user by means of various reactions. The watchdog is idle when the PC is switched on or after a HW-RESET(cold restart), i.e., no reaction of the WD is triggered.
Functions 11.5 Fan monitoring 11.5 11.5 Fan monitoring This function monitors operation of the housing and processor fans.
12 Maintenance and service 12.1 12.1 Servicing Scope of maintenance When working in areas where there is dust that may be hazardous to functionality, the device must be operated in a control cabinet with a heat exchanger or with suitable supply air. Note Dust deposits must be removed at regular intervals. Maximum dust content in the air circulating in the cabinet Suspended component 0.2 mg/m3 Deposits 1.5 mg/m3/h Cleaning agents Use dish soap or foaming screen cleaner only as cleaning agents.
Maintenance and service 12.1 Servicing Chemical stability Caution Adhere to the information regarding chemical resistance of the panel front. Please go to http://www.siemens.com/asis under "Tools & Downloads" for more information. Enter the article ID 16532108 as the search term. The available articles are displayed. Procedure for cleaning the device 1. Switch off the device. This prevents the accidental triggering of functions when the screen is touched. 2. Dampen the cleaning cloth. 3.
Maintenance and service 12.2 Replacement parts 12.2 12.2 Replacement parts The device has the following replacement parts: Replacement part Key panel 12''-TFT 15''-TFT Touch panel 15''-TFT 19''-TFT Key front, without front USB interface*) 12'' TFT 15'' TFT Touch front, without front USB interface*) 15'' TFT 19'' TFT Order No.
Maintenance and service 12.3 Separating the control unit from the computer unit 12.3 12.3 Separating the control unit from the computer unit Introduction The control unit is separated from the computer unit to carry out repairs or to replace the control unit, for example. Procedure 1. Disconnect the device from mains. 2. Open the switchgear cabinet. The device is now accessible from the back. 3.
Maintenance and service 12.3 Separating the control unit from the computer unit 5. Loosen cables K1 to Kx and the USB cable between the computer unit and the control unit 6. Two mounting rails are screwed onto the computer unit whose angled ends (4) are located in the corresponding recesses in the computer unit. Lift the computer unit vertically out of these recesses 7. Put the computer unit down carefully. 8.
Maintenance and service 12.3 Separating the control unit from the computer unit Separating the device in an uninstalled state As an alternative, dismount the device completely and separate the control unit and computer unit from one another in an uninstalled state. So that the processing unit, which is swung away from the control unit, does not bend the lugs (4), place a surface under the processing unit.
Maintenance and service 12.4 Installing and removing hardware components 12.4 12.4.1 12.4 Installing and removing hardware components Repairs Notice Similar to figure The images presented below deviate slightly from the actual device in some respects. Carrying out repairs Only authorized personnel are permitted to repair the device. Warning Unauthorized opening and improper repairs on the device may result in substantial damage to equipment or endanger the user.
Maintenance and service 12.4 Installing and removing hardware components 12.4.2 Open the device Caution Work on the open device may only be carried out by authorized and qualified personnel. Within the warranty time, you are only allowed to install expansions for memory and expansion card modules. Caution The device contains electronic components which may be destroyed by electrostatic charge. You therefore need to take precautionary measures before you open the device.
Maintenance and service 12.4 Installing and removing hardware components Open the device Steps for opening the device 1 Remove the five screws (1). 2 Swing the lid to the front and remove it.
Maintenance and service 12.4 Installing and removing hardware components 12.4.3 Installing and removing memory modules Memory expansion The motherboard is equipped with 2 slots for memory modules. 184 pin DDR266 or PC2700 memory modules can be used, unbuffered, no ECC. This enables you to expand the memory capacity of the device to a maximum of 2 GB. These slots can be fitted with one or two memory modules.
Maintenance and service 12.4 Installing and removing hardware components Installing a memory module How to install a memory module 1 Open the device. 2 Note the recess and polarity reversal protection on the connector side of the memory module. 3 Push the module carefully into the slot until the interlocks engage 4 Close the device Removing a memory module How to remove a memory module 1 Open the device.
Maintenance and service 12.4 Installing and removing hardware components 12.4.4 Installing PCI / AT cards 12.4.4.1 Notes on the modules Notes on module specifications The device is designed for use with modules conforming to AT/PCI specifications. PCI modules with 5 V and 3.3 V supply voltage can be operated. The permitted dimensions of the modules are found in the dimensional drawings section.
Maintenance and service 12.4 Installing and removing hardware components 12.4.4.2 Installing / removing expansion modules Preparation Disconnect the device from mains. Installing expansion modules How to install an expansion module (PCI / AT format): 1 Open the device. 2 Loosen the two fastening screws (1) and remove the module holding-down device (2). 3 Remove the relevant steel slot cover (3). 4 Insert the expansion module (4) into the relevant slot.
Maintenance and service 12.4 Installing and removing hardware components Inserting the slider To insert the slider: How to install a module holding-down device 1 Push the slider through the guide slot until it is seated firmly on the module. Insert the module into the slot. Caution Do not apply any pressure to the module Therefore, do not apply excessive force to the slider when you push it onto the module.
Maintenance and service 12.4 Installing and removing hardware components 12.4.4.3 Exchanging the RAID controller PCI card Introduction The RAID system uses the following controllers: • System with SATA drives: Promise Fast Track TX2300 Principle The RAID controller PCI card is installed in PCI slot 5 of the bus module.
Maintenance and service 12.4 Installing and removing hardware components 12.4.5 Disk drives 12.4.5.1 Options of installing disk drives Drive bay module for hard disk drives, optical drives and floppy disk drives DVD-ROM/CD-RW drive bay Hard disk drive bay for one 3.5" drive 12-16 Pos Description (1) DVD-ROM/CD-RW drive bay (2) Mounting slot for DVD-ROM or DVD-ROM/CD-RW drive Pos Description (1) Hard disk drive bay for one 3.5" drive (2) Mounting slot for a 3.
Maintenance and service 12.4 Installing and removing hardware components Drive bays for two 2.5" hard disks Drive bay for floppy disk drive SIMATIC Panel PC 877 Operating instructions, Release 07/2006, A5E00877780-01 Pos Description (1) Hard disk drive bay for 2.5" hard disks (2) Two mounting slots for 2.
Maintenance and service 12.4 Installing and removing hardware components 12.4.5.2 Installing / removing a drive bay Preparations Disconnect the device from mains and unplug all cables.
Maintenance and service 12.4 Installing and removing hardware components Removing drive bays for floppy disk drives Steps for removing the floppy disk drive bay 1 Remove the four screws (1) 2 Remove the hard drive bay and place it onto the device.
Maintenance and service 12.4 Installing and removing hardware components Steps for removing the floppy disk drive bay 12-20 3 Remove the data cable between the floppy disk drive (1) and the motherboard and its power supply connector (2). Remove the screw (3) and open the bracket. Disconnect the connecting cable for the optical drive.
Maintenance and service 12.4 Installing and removing hardware components 12.4.5.3 Removing and installing an optical drive Procedure 1. Unscrew the 4 screws (1) holding the drive and slide the drive out. Figure 12-4 Installing and removing the optical drive 1. If you need to completely remove the drive, remove drive connectors (1) and (2) from the device.
Maintenance and service 12.4 Installing and removing hardware components Figure 12-5 Drive connectors 2. Loosen the 2 screws (1) of the drive housing. Figure 12-6 Drive with housing 3. Flip up the housing cover (1) 90°.
Maintenance and service 12.4 Installing and removing hardware components Figure 12-7 Drive removed, housing flipped up 4. Remove the connector of the ribbon cable from the socket (2). 5. Loosen the 3 screws (3) with a TX6 key. 6. Remove the drive (4) from the bracket. 7. Loosen the 2 screws (5) on the board (6). Notice Loose spacer bolts are located between the housing and the board. When loosening the board, hold the spacer bolts in place. 8. Remove the board (6).
Maintenance and service 12.4 Installing and removing hardware components 12.4.5.4 Removing and installing a 3.5" hard disk Procedure 1. Unscrew the 4 screws from the drive housing and slide the drive out. The drive is secured to the underside of the drive housing. 2. Note the cable arrangement and then remove the cables from the motherboard. Figure 12-8 Removed hard disk 3. Loosen the 4 screws that secure the hard disk to the drive bay. 4. Remove the drive from the bracket.
Maintenance and service 12.4 Installing and removing hardware components 12.4.6 Replacing the backup battery Note Batteries are wearing parts and should be replaced every five years in order to ensure proper functioning of the PC. To be noted before you replace the battery Caution Risk of damage! The lithium battery may only be replaced with an identical battery or with a type recommended by the manufacturer (Order No.: A5E00331143).
Maintenance and service 12.4 Installing and removing hardware components Preparation Note The configuration data of the device are deleted when the battery is replaced. 5. Note down the current settings of the BIOS Setup. A list in which you can note down this information is found in the BIOS manual. 6. Disconnect the device from mains and unplug all cables. Replacing the battery Follow the steps outlined below: Steps for replacing the battery 1 Open the device.
Maintenance and service 12.4 Installing and removing hardware components 12.4.7 Removing/Installing the Power Supply Warning Only qualified personnel is authorized to exchange the power supply module. Preparations 1. Disconnect the device from mains and unplug all cables. 2. Open the device. Removing the power supply module How to remove the power supply module 1 Remove the hard disk drive bay. 2 Remove the 6 screws (1) and the cover of the power supply module.
Maintenance and service 12.4 Installing and removing hardware components How to remove the power supply module 12-28 5 Disconnect the power supply connector from the motherboard. 6 Pull the power supply module out to the front. 7 Also remove the four screws holding the steel bracket of the PS and take it off. These are special screws with imperial dimensions (6-32x3/16''-St-G3E).
Maintenance and service 12.5 Installing Software 12.5 12.5.1 12.5 Installing Software General installation procedure If the system is unstable or if the operating system reports errors, the delivery status of the device can be easily restored using the Restore DVD. You can re-install the operating system and relevant drivers using the Recovery CD and the "Documentation and Drivers" CD. Recovery CD: The new recovery procedure is based on Windows PE (Preinstalled Environment).
Maintenance and service 12.5 Installing Software 12.5.2 Setting up the partitions for Windows operating systems After you have installed a new hard disk, or if partitions are faulty, or when you wish to change the partitioning on your hard disk, you need to create or reconfigure partitions on the hard disk Caution When you delete or create partitions or logical DOS partitions, you lose all data on the hard disk. All partitions on the hard disk will be deleted.
Maintenance and service 12.5 Installing Software Note Once you have changed the configuration of your hard disk with DiskPart, you will need to reboot the PC for the changes to go into effect. Boot again from the Recovery CD to format the partitions. Format primary partition 1. Boot from the Recovery CD to format the partitions. Follow the screen instructions until the Recovery functions window is displayed. 2. Select "Start command prompt" in the Recovery functions window.
Maintenance and service 12.5 Installing Software 12.5.3 Compatibility of the Restore DVD Caution Use only the supplied Restore DVDs for the device. Verify that the order number of the Restore DVD matches that of the device. You can find the order number of the device on the rating plate. Do not use the supplied images for any other device. The chipsets and drivers differ.
Maintenance and service 12.5 Installing Software 12.5.4 Restoring the factory state of the software using the Restore DVD You can restore the software to the original factory state using the Restore CD (not included in all package variants). The DVD contains the necessary images and tools for transferring the factory software to the hard disk of your PC. You can restore the entire hard disk with drive C: (system) and drive D: or only drive C:. at the command line input.
Maintenance and service 12.5 Installing Software Restoring the factory state with an external USB CD/DVD ROM Procedure: 1. Connect the external USB CD/DVD ROM to the Panel PC and reboot the device. 2. Activating the Legacy Support in the BIOS – Press the key when the BIOS message "Press to enter Setup" appears.
Maintenance and service 12.5 Installing Software 12.5.5 Installing Microsoft Windows operating systems 12.5.5.1 Operating system not installed The device can be optionally purchased without an operating system. If you want to install the operating system yourself, read the information available in the Internet at http://www.siemens.com/asis Notice You must integrate the required software components yourself if you install an operating system not offered by Siemens AG.
Maintenance and service 12.5 Installing Software 12.5.5.2 Booting from the Recovery CD Please use the Recovery CD to install Windows to meet your special requirements. The operating system used is Windows Preinstall Environment (WinPE). You will also need the supplied Documentation and Drivers CD. Booting with the Recovery CD: 1. Insert the Recovery CD in the drive and reboot the device. When the BIOS message ”Press to enter Setup or to show Boot Menu" appears, press the ESC key.
Maintenance and service 12.5 Installing Software 12.5.5.3 Installing the Microsoft Windows operating system (not for RAID) The recovery CD contains encrypted data that can only be transferred to this system. Please use the Recovery CD to install Windows to meet your special requirements. The operating system used is Windows Preinstall Environment (WinPE). You will also need the supplied Documentation and Drivers CD. Booting with the Recovery CD 1.
Maintenance and service 12.5 Installing Software 12.5.5.4 Installing the Microsoft Windows operating system (for RAID) RAID Recovery Notes on RAID systems (Optional) To install the operating system with the RAID option, the following steps must be carried out: 1. When the device starts up, press + to enter the BIOS setup of the RAID controller. 2. Select the AUTO SETUP option, to connect a RAID (choice between RAID 0 "Stripe" and RAID 1 "Mirror"). 3.
Maintenance and service 12.5 Installing Software 12.5.6 Installing individual drivers Introduction The "Documentation and Drivers" CD contains the required drivers for the device. Procedure 1. Start "Start.exe" in the root directory of the CD. 2. Follow the instructions displayed on the screen. Note For further information on reinstalling the drivers, go to http://www.siemens.com/asis, under "Support".
Maintenance and service 12.5 Installing Software 12.5.7 Operation of two hard disks The two hard disks are configured as follows in the factory state of the computer: Hard disk 0 Hard disk 1 Partition C: System, NTFS, 10 GB Not configured Partition D: Data, NTFS, remaining capacity You can use the two hard disks as a 2 HHD system. 12.5.7.1 2 HDD system Depending on the device features, the Panel PC 877 can be equipped with two 2.5“ (PATA) hard disk drives. The slave hard disk drive is not set up.
Maintenance and service 12.5 Installing Software 12.5.7.2 RAID system with Promise Fast Track Controller TX2300 RAID 0 system A RAID 0 system (Stripe) enables you to increase the read/write speed of your hard disk system. This configuration reduces the reliability of the drive system, however. RAID 0 is therefore not recommended and is omitted from the installation instructions. RAID 1 system A RAID 1 system (mirroring) enables you to increase the data security of your hard disk system.
Maintenance and service 12.5 Installing Software Functions for RAID system management The preinstalled software of the RAID system offers enhanced functions for using and managing the RAID system. SATA-RAID software is started via "Start > Programs > Promise Array Management > Local PAM". Access to the RAID is protected by user and password. Factory setting: • User: Administrator • Password: empty Notice The security functions of the RAID system are effective without launching the software.
Maintenance and service 12.5 Installing Software Configuring a RAID 1 system Prerequisites • Two identical SATA hard disks; the primary hard disk contains the operating system and data (boot drive), the second hard disk is empty. • If the DiagMonitor has been installed, the DiagMonitor Agent must be stopped. To exit the DiagMonitor agent, enter the command "NET STOP SNMP" in the DOS box.
Maintenance and service 12.5 Installing Software 12.5.7.3 Installing the RAID Controller software The procedure for installing the software can be found in the RAID user manual on the supplied Documentation and Drivers CD. Note concerning Windows 2000 Professional / XP Professional You need to select the type Promise FastTrack TX 2300 controller from the provided list when installing Windows 2000 Professional / XP Professional for the first time.
Maintenance and service 12.5 Installing Software 12.5.8 Installing burner and DVD software The supplied CD provides information about installation of the burner and DVD software.
Maintenance and service 12.5 Installing Software 12.5.9 Backing up the hard disk The device's hard disk is divided into two partitions, volumes C and D. The operating system is installed on volume C. Volume D can be used for user data. Back up the complete hard disk regularly, for example, using "SIMATIC PC/PG Image Partition Creator". This software can be purchased as an accessory, Order No. 6ES76486AA03-0YX0. Caution Date errors writing to CD-RW The quality of raw disc differs considerably.
Alarm, error and system messages 13.1 13.1 13 Boot error messages During startup (the boot process), the BIOS first performs a Power On Self Test (POST) and checks whether certain functional units of the PC are operating error-free. When an error occurs within this phase, the BIOS outputs a tone sequence (beep code) based on the current test result. The boot sequence is interrupted immediately if fatal errors occur.
Alarm, error and system messages 13.1 Boot error messages 13-2 On-screen error message Meaning / suggestions Keyboard error Check whether the keyboard is properly connected. Key seizure Check whether a key on the keyboard has seized. System RAM Failed at offset: Memory error. Contact your technical support team. Shadow RAM Failed at offset: Memory error. Contact your technical support team. Extended RAM Failed at offset: Memory error. Contact your technical support team.
Alarm, error and system messages 13.2 Introduction to the BIOS beep codes 13.2 13.2 Introduction to the BIOS beep codes The device performs a self-test when it is switched on. If an error is detected during the POST (Power On Self Test), a series of beep signals are issued. The beep tones are a code for errors and are composed of 2 x 2 sequences.
Alarm, error and system messages 13.2 Introduction to the BIOS beep codes Special codes The following special code are provided in addition to the beep codes: 13-4 Special code Meaning 3x short The key is pressed during the system start: The on-board device installation is skipped. The on-board graphic controller is used as the default display. 1x long 8x short Error reading the MPI system information. Contact customer service. 4x short MPI-EPROM programmed for the first time.
Alarm, error and system messages 13.3 BIOS beep codes 13.3 13.3 BIOS beep codes The following section lists the POST codes relevant to users in the sequence in which they occur: Contact Customer Support for all other POST codes.
Alarm, error and system messages 13.3 BIOS beep codes Special codes The following Beep codes are available in addition to the listed POST codes: • 3 x short INSERT key is pressed on system start: If an external graphics card on the bus board is not detected, you can try to activate it by pressing the INSERT key. The "INSERT" key activates special enumerations for activating a PCI VGA card.
14 Troubleshooting/FAQs 14.1 14.1 General problems This chapter provides you with tips on how to localize and troubleshoot frequently occurring problems. Problem Possible causes To correct or avoid error The device is not operational There is no power supply to the device. • • Check the power supply, the network cable and the power plug. Check whether the On/Off switch is in the correct position. Device is being operated outside the specified ambient.
Troubleshooting/FAQs 14.2 Problems when Using Modules of Third-party Manufacturers 14.2 14.2 Problems when Using Modules of Third-party Manufacturers Problem Possible causes The PC crashes during startup • • • • • • 14-2 To correct or avoid error I/O addresses are assigned twice. Hardware interrupts and/or DMA channels are assigned twice. Signal frequencies or signal levels are incorrect. Connector assignments deviate. “Reset Configuration” in BIOS SETUP has not been carried out.
Troubleshooting/FAQs 14.3 Temperature limits 14.3 14.3 Temperature limits Cause If the device is used for its intended purpose, the temperature threshold values are not exceeded or fallen below.
Troubleshooting/FAQs 14.
15 Technical data 15.1 15.1 General technical data General technical data AC device: Supply voltage 100 to 240 V AC (85 to 265 V AC) DC device: Supply voltage 24 V DC (20.4 to 28.8 V DC) SELV AC device: Frequency 50 - 60 Hz (47 to 63 Hz) Transient voltage interruption according to Namur AC device: At least 20 ms for 93 to 264 V at most 10 events per hour; recovery time of at least 1 s DC device: no buffering AC device: Max.
Technical data 15.1 General technical data General technical data Electromagnetic compatibility (EMC) AC device: Emitted interference EN 55011 Class A, EN 61000-3-2 Class D EN 61000-3-3 DC device: Emitted interference EN 55022 Class A Noise immunity: Mains borne disturbance variables on supply lines ± 2 kV; according to IEC 61000–4–4; Burst ± 1 kV; according to IEC 61000–4–5; Surge sym. ± 2 kV; according to IEC 61000–4–5; Surge asym.
Technical data 15.1 General technical data General technical data Motherboard Processor Intel ® Pentium 4 2.8 GHz Intel ® Celeron 2 GHz Intel ® Pentium 4 Mobile 2.2 GHz Internal processor cache Intel ® Pentium 4 2.8 GHz, 512 KB Intel ® Celeron 2 GHz, 128 KB Intel ® Pentium 4 Mobile 2.2 GHz, 512 KB Front Side Bus Intel ® Pentium 4 2.8 GHz, 533 MHz Intel ® Celeron 2 GHz, 400 MHz Intel ® Pentium 4 Mobile 2.
Technical data 15.1 General technical data General technical data PROFIBUS/MPI interface electrically isolated 3) • Transmission rate • Mode groups • 9-pin sub-D socket • 9.6 Kbps to 12 Mbps, configured per software • Electrically isolated: Data channels A, B Control channels RTS AS, RTS_PG 5 V power supply (max.
Technical data 15.1 General technical data General technical data Panel PC 877 12" TFT Key front 15" TFT Key front 15" TFT Touch screen 19" TFT Touch screen Service life of backlighting 50,000 h for 24 hours per day usage, temperature dependent, 50% residual brightness remains Membrane keyboard with alphanumeric and numeric keys X — Function keys 36 with LED — Direct control key module optional — Actuating force (test pen 3 mm with 3 mm radius) max.
Technical data 15.1 General technical data General technical data Safety Protection class Protection class I to IEC 60536, i.e.
Technical data 15.
Technical data 15.2 Power requirements of the components 15.2 15.2 Power requirements of the components Standard system Components Motherboard Voltage +5 V +3.3 V +12 V 1.3 A 4.8 A 0.2 A Intel ® Pentium 4 Desktop or Celeron processor with active heat sink -5 V -12 V 5 Vaux 0.03 A 0.3 A 0.5 A 0.25 A 0.25 A 5.8 A Intel ® Pentium 4 Mobile processor 7 A with active heat sink Diskdrive 0.6 A Hard disks-drive; 1 x 3.5'' 0.3 A 0.5 A DVD-ROM/CD-RW drive 0.9 A 0.8 A Equipment fan 0.
Technical data 15.3 Device with AC voltage supply 15.3 15.3 Device with AC voltage supply Technical data Input voltage 100 to 240 V AC (85 to 264 V AC) Frequency 50 - 60 Hz Power consumption 360 W Power failure buffering 20 ms Maximum continuous output power 230 W Degree of protection IP20 (in installed state) Protection class VDE 0106 Voltage Max. current + 12 V 12.2 A peak 14 A Output voltages - 12 V 0.8 A +5V 25 A 1 -5V 0.5 A + 3.3 V 10 A 1 + 5 Vaux 2 A peak 2.
Technical data 15.4 Device with DC voltage supply 15.4 15.4 Device with DC voltage supply Technical data Input voltage 24 V DC (20.4 to 28.8 V DC) Power consumption 265 W Power failure buffering 1 ms at nominal voltage Maximum continuous output power 180 W Degree of protection IP20 (in installed state) Protection class VDE 0106 Voltage Max. current + 12 V 4.4 A Output voltages - 12 V 0.5 A +5V 22 A 1 -5V 0.5 A + 3.3 V 16 A 1 + 5 Vaux 1A 1 The max.
Technical data 15.5 Keyboard table 15.5 15.5 Keyboard table Key codes The following table applies only to control units with key panels. It contains all characters that can be entered in SIMATIC KeyTools in the "Key code table" area and under "User specific". The character that is triggered by pressing a specific key is listed in the "Display/function" column. Further information is available in the documentation for SIMATIC KeyTools on the "Documentation and Drivers" CD.
Technical data 15.
Technical data 15.
Technical data 15.
Technical data 15.5 Keyboard table Name Code (Hex) 0x Check-box -_ 2D — - L Shift/R Shift _ =+ [{ ]} \| 2E 2F 30 31 Display/function R Alt ¥ — = L Shift/R Shift + R Alt × R Alt+L Shift/R Shift ÷ — [ L Shift/R Shift { R Alt « — ] L Shift/R Shift } R Alt » — \ L Shift/R Shift | R Alt ¬ R Alt+L Shift/R Shift ¦ Europe 1 32 — Europe 1 ;: 33 — ; ’" ‘~ ,< 34 35 36 .
Technical data 15.
Technical data 15.
Technical data 15.
16 Dimension drawings 16.1 Panel PC 877 dimensional drawing , - PP . 16.
Dimension drawings 16.
Dimension drawings 16.2 Dimensional drawings for the installation of expansion modules 16.2 16.
Dimension drawings 16.
Detailed descriptions 17.1 17.1.1 17.1 17 Motherboard Structure and functions of the motherboard The essential components of the motherboard are the processor and the chip set, two slots for memory modules, internal and external interfaces and the Flash BIOS.
Detailed descriptions 17.1 Motherboard 17.1.2 Technical features of the motherboard Component / interface Description Characteristics Chip set Single chip set VIA P4N266A (VT8703A and VT8235) BIOS Update by means of software Phoenix NuBIOS V4, modified by Siemens CPU Intel ® Pentium 4 / Mobile P4 Upgradable / Intel ® Celeron (design • Multimedia support mPGA478) • On-board L2-Cache with 512 K / 512 K / 128 K Memory 2 DIMM module slots, max.
Detailed descriptions 17.
Detailed descriptions 17.1 Motherboard 17.1.3 Position of the ports on the motherboard Interfaces The motherboard of the device features the following interfaces: • Interfaces for the connection of external devices • Interfaces for internal components (drives, bus boards etc.) The figure below shows the location of the internal and external interfaces on the motherboard.
Detailed descriptions 17.1 Motherboard 17.1.4 External interfaces Interface Positio n COM1 Externa X30 l 25-pin socket, V.24/V.28 COM2 Externa X31 l 9-pin, standard connector LPT1 Externa l 25-pin, standard socket PS/2 mouse Externa X22 l 6-pin, miniature DIN socket PS/2 keyboard Externa X23 l 6-pin, miniature DIN socket USB 2.
Detailed descriptions 17.1 Motherboard Serial interface COM 1, X30 The serial interface (COM 1) on the device has the following pinout: Serial interface COM 1 (socket) PinNo.
Detailed descriptions 17.1 Motherboard COM 2 serial interface (V24/Mouse), X31 The serial interface (COM 2) has the following pinout: COM 2 serial interface (V24/Mouse) PinNo.
Detailed descriptions 17.1 Motherboard LPT1 parallel interface, X134 The parallel interface (LPT 1) has the following pinout: Parallel interface LPT1 PinNo.
Detailed descriptions 17.1 Motherboard PS/2 mouse interface, X22 Pin assignment of the interface: PS/2 Pin No. Abbreviation Meaning 1 DAT Data channel, mouse Input/output Input/Output 2 – Not assigned – 3 GND Ground – 4 P5VFK + 5 V (fused) Output 5 CLK Clock channel, mouse Input/output 6 – Not assigned – PS/2 keyboard interface, X23 Pin assignment of the interface: PS/2 Pin No.
Detailed descriptions 17.1 Motherboard PROFIBUS/MPI interface, X400 The PROFIBUS/MPI socket has the following pinout: PROFIBUS/MPI interface 1) PinNo. Abbreviation Meaning Input/Output 1 – Not assigned – 2 – Not assigned – 3 LTG_B Signal line B of MPI module Input/output 4 RTS_AS RTSAS, control signal for received data stream. The signal is "1" active when the directly connected PLC is sending. Input 5 M5EXT M5EXT return line (GND) of the 5 V power supply.
Detailed descriptions 17.1 Motherboard Ethernet RJ45 connection, X700 Ethernet RJ45 connection PinNo.
Detailed descriptions 17.1 Motherboard DVI interface, X303 The DVI socket has the following pinout: DVI interface 17-12 PinNo.
Detailed descriptions 17.1 Motherboard 17.1.5 Front interfaces Overview Interface Position Connector Description Display (LVDS) Internal X300 Connection of LCD displays with LVDS interface (channel 1) Display (LVDS) Internal X310 Connection of LCD displays with LVDS interface (channel 2) I/O front Internal X44 Interface for I/O front COM2 Internal X33 Internal COM2 interface USB Internal X2033 Internal USB 2.
Detailed descriptions 17.1 Motherboard Display interface (1st LVDS channel), X300 Pin No. Abbreviation Meaning Input/Output 1 P5V_D_fused +5V (fused) display VCC Output 2 P5V_D_fused +5V (fused) display VCC Output 3 RXIN0- LVDS output signal bit 0 (-) Output 4 RXIN0+ LVDS output signal bit 0 (+) Output 5 P3V3_D_fused +3.3V (fused) display VCC Output 6 P3V3_D_fused +3.
Detailed descriptions 17.1 Motherboard Display interface (2nd LVDS channel), X310 Pin No.
Detailed descriptions 17.1 Motherboard I/O front interface for operator panels, X44 This interface carries all signals required for the connection of operator panels in addition to the display and USB interface. The maximum cable length is 50 cm at a USB data rate of 12 Mbps. Pin No. Abbreviation Meaning Input/Output 1 GND Ground - 2 P12V Inverter voltage supply Output 3 BL_ON Backlight ON (5 V = ON) Output 4 P5V_fused +5 V (fused) Output 5 GND Ground - 6 P3V3_fused +3.
Detailed descriptions 17.1 Motherboard Assignment of the display to the display select pins The display select inputs are used to configure one of 15 possible displays automatically. The display select inputs are equipped with pull-up resistors, i.e., these inputs have a high signal if they are not connected. The input must be connected to GND if a low signal is to be generated. Pin No.
Detailed descriptions 17.1 Motherboard 17.1.
Detailed descriptions 17.1 Motherboard Interface Position Connector Description On / Off switch Internal X53 Switches off the power supply on the secondary side, the AUX voltage is not switched off.
Detailed descriptions 17.1 Motherboard Connection for optical drive, X12 Pin No.
Detailed descriptions 17.1 Motherboard Interface to floppy disk drive, X26 This interface is designed for connecting a standard floppy drive. The maximum length of the data cable should not exceed 40 cm. Pin No.
Detailed descriptions 17.1 Motherboard Pinout of the CPU fan power supply, X41 Pin No. Abbreviation Meaning Input/Output 1 GND Ground - 2 +12 V Switched power supply Output 3 CPU FAN_CLK Clock signal Input Pinout of the main fan power supply, X42 Pin No. Abbreviation Meaning Input/Output 1 GND Ground - 2 +12 V Switched power supply Output 3 PG1 FAN_CLK Clock signal Input Additional power supply connector (12V) for devices with 19'' front, X45. Pin No.
Detailed descriptions 17.1 Motherboard Pinout of the internal USB interface connector, X2033 Pin No. Abbreviation Meaning 1 VCC 3.3V +3.3V, fused 2 VCC 5V + 5 V, fused 3 USB3 USB3_M 4 USB5 USB5_M 5 USB3 USB3_P 6 USB5 USB5_P 7 GND Ground 8 GND Ground 9 GND Ground 10 GND Ground Pinout of the USB 2.0 interface, X2034 Pin No.
Detailed descriptions 17.2 Bus board 17.2 17.2.1 17.2 Bus board Layout and principle of operation The bus board is designed as a link between the motherboard and the expansion modules. It is mounted with two screws. The bus board has two PCI expansion slots (2x long), two long shared ISA/PCI and one long ISA slot. It can host expansion modules conforming to ISA specification (Rev. 3.1) and PCI specification (Rev. 2.0 for 5 V and 3.3 V modules). All PCI slots are master–capable.
Detailed descriptions 17.2 Bus board 17.2.2 Assignment of the PCI IRQ channels to the PCI slots Assignment of the PCI IRQ channels to the PCI slots Box PC 840 V2 PCI modules interrupt assignment (PCI IRQ) in: Module interrupt (Pin Slot 1 No.
Detailed descriptions 17.2 Bus board 17.2.3 Exclusive PCI hardware interrupt Applications demanding a high-performance interrupt require a high-speed hardware interrupt reaction. The PCI hardware interrupt should be used only by one resource in order to ensure high-speed reaction of the hardware. This can be forced by appropriate setting in the system BIOS. Setting up a reserved interrupt on the device A reserved interrupt can only be set and used for PCI slots 2 and 4.
Detailed descriptions 17.2 Bus board 17.2.4 ISA slot pin assignment Pin No. Abbreviation Type* Pin No.
Detailed descriptions 17.2 Bus board Pin No. Abbreviation Type* Pin No.
Detailed descriptions 17.3 Operating system licenses 17.3 17.3 Operating system licenses Description: The supplied and installed Windows operating systems of the SIMATIC PCs are full Windows versions without any function restrictions. The additional wording "For Embedded Systems" on the accompanying operating system Recovery CD describes the contractual conditions under which Siemens AG acquires the licenses from Microsoft.
Detailed descriptions 17.4 Cables 17.4 17.4 Cables SIMATIC S7 cable for MPI/DP The 6ES7901-0BF00-0AA0 cable is used to connect the device to a SIMATIC S7 automation device. Refer to the "Integration" section for more information.
Detailed descriptions 17.5 System resources 17.5 17.5.1 17.5 System resources Currently allocated system resources All system resources (hardware addresses, memory configuration, interrupt assignment, DMA channels) are assigned dynamically by the Windows OS, depending on the hardware configuration, drivers, and connected peripheral devices.
Detailed descriptions 17.5 System resources 17.5.2 System resources used by the BIOS/DOS The following table describes the system resources for the factory state of the device. 17.5.2.
Detailed descriptions 17.
Detailed descriptions 17.5 System resources 17.5.2.2 Interrupt Assignments Interrupt Description Comment IRQ0 System timer fixed IRQ1 Keyboard fixed IRQ4 Serial port COM1 2) IRQ8 Real-time clock (RTC) fixed IRQ9 Microsoft ACPI-Compliant System 1) IRQ13 Numeric processor fixed IRQ14 1.
Detailed descriptions 17.5 System resources 17.5.2.3 Memory address assignments PCI VGA modules can be operated with an expansion ROM of a size up to 48 K.
Detailed descriptions 17.6 BIOS setup 17.6 17.6.1 17.6 BIOS setup Overview BIOS SETUP program The BIOS SETUP program is stored in the ROM BIOS. Information about the system configuration is stored in the battery-backed RAM of the device. You can use SETUP to set the hardware configuration (for example, the hard disk type) and define the system properties. You can also use SETUP to set the time-of-day and date.
Detailed descriptions 17.6 BIOS setup 17.6.2 Starting BIOS Setup Starting BIOS Setup Start the setup program as follows: Reset the device (warm or cold restart). In the figures shown, the default settings differ based on the device versions. With the default setting of your device, the display shown below appears following power-on, for example: Phoenix BIOS 4.0 Release 6.0 Copyright 1985 - 2002 Phoenix Technologies Ltd.
Detailed descriptions 17.6 BIOS setup 17.6.3 BIOS setup menus The various menus and submenus are listed on the next pages. You can obtain information on the selected SETUP item from the "item-specific help" part of the respective menu.
Detailed descriptions 17.6 BIOS setup Menu layout The screen is divided into four sections. In the top part (4), you can select the menu forms [Main], [Advanced], [Security], [Power], [Boot Sequence], [Version], [Exit]. In the left of the center section (3) you can select various settings or submenus. Brief help texts appear on the right (1) for the currently selected menu entry. The bottom section contains information for operator input.
Detailed descriptions 17.6 BIOS setup 17.6.
Detailed descriptions 17.
Detailed descriptions 17.
Detailed descriptions 17.6 BIOS setup Array Meaning Type The parameters which you can select here are usually saved on the respective IDE drive. The 'Auto' setting in the 'Type' field means that these values are automatically read from the drive and written to memory (Auto detect). If Type is selected for a drive that cannot be detected, a time-out is triggered within approximately 1 minute and the entries remain unchanged.
Detailed descriptions 17.6 BIOS setup "Memory cache" field The following context menu appears when you select the option “Memory cache” in the main menu: Figure 17-5 "Memory Cache" field The cache is a high-speed memory buffer between the CPU and memory (DRAM). Repeated memory access operations are executed in the fast cache, and not in the main memory, provided the feature is enabled.
Detailed descriptions 17.6 BIOS setup "Boot options" field The following context menu appears when you select “Boot options” in the main menu: Figure 17-6 "Boot Options" field Quick Boot Mode Some hardware tests are skipped to speed up the boot sequence. SETUP prompt During the system load phase, the message Press to enter Setup or to show boot menu is output on the bottom of the screen. POST errors The boot sequence is stopped if an error is detected; you must press F1 to acknowledge.
Detailed descriptions 17.6 BIOS setup Example of a summary screen: Figure 17-7 Summary Screen (Example) The Summary screen appears when the system boot phase completes.
Detailed descriptions 17.6 BIOS setup "Keyboard features" field The following submenu appears when you select the option “Keyboard features” in the main menu: Figure 17-8 "Keyboard Features" submenu (Example) Numlock Switches Numlock on or off following power on. Key Click A keystroke can be heard with a "CLICK".
Detailed descriptions 17.6 BIOS setup "Hardware options" field The following submenu, for example, appears when you select “Hardware options” in the main menu: Figure 17-9 "Hardware Options" submenu (Example) The parameters of the interfaces present on the motherboard are set here.
Detailed descriptions 17.6 BIOS setup Entry Meaning PCI-MPI/DP On-board Ethernet Ethernet Address 1) Optional 1 Enables the CP5611-compatible MPI/DP interface. The resources are managed by the BIOS PCI Plug&Play mechanism. [Enabled] The Ethernet interface on the motherboard is enabled. [Disabled] The Ethernet interface on the motherboard is disabled. Shows the individual Ethernet address. product feature Entry Meaning LAN Remote Boot [Enabled] Booting via a connected LAN is possible.
Detailed descriptions 17.6 BIOS setup Entry Meaning On-chip USB A [Enabled] On-chip USB A determines the function of USB ports 0 and 1. Onchip USB A occupies PCI IRQ Channel 1. On-chip USB A port 0 is located on the front interface socket X44, port 1 on the bottom of the device rear X36. Users cannot edit this value. OnChip USB B [Enabled] On-chip USB B determines the function of USB ports 2 and 3. Onchip USB B occupies PCI IRQ Channel 2. On-chip USB B port 3 is located on internal X2033.
Detailed descriptions 17.6 BIOS setup 17.6.5 Advanced menu Menu layout 3KRHQL[%,26 6HWXS 8WLOLW\ 0DLQ $GYDQFHG ,QVWDOOHG 2 6 5HVHW &RQILJXUDWLRQ 'DWD 6HFXULW\ 3RZHU 9HUVLRQ ([LW ,WHP 6SHFLILF +HOS >2WKHU@ >1R@ 6HOHFW WKH RSHUDWLQJ V\VWHP LQVWDOOHG , 2 'HYLFH &RQILJXUDWLRQ 3&, &RQILJXUDWLRQ /RFDO %XV ,'( DGDSWHU /DUJH 'LVN $FFHVV 0RGH %RRW >3ULPDU\ 6HFRQG@ >'26@ 86% %RRW >'LVDEOHG@ 86% OHJDF\ .
Detailed descriptions 17.6 BIOS setup Settings in the Advanced menu Installed O/S Plug&Play means that all modules are automatically detected and installed, providing they support the Plug&Play functionality. [Other] BIOS handles the entire Plug&Play capability, default setting. [Win95] BIOS handles the entire Plug and Play capability [Win98] The operating system handles some of the Plug&Play functions. [WinMe] The operating system handles the Plug&Play functions.
Detailed descriptions 17.6 BIOS setup USB legacy keyboard/mous e USB segment location Default primary video adapter Frame buffer size [Disabled] Disables Legacy Universal Serial Bus support [Enabled] This function determines whether a USB keyboard or USB mouse can be used with software or tools on an MS-DOS platform (e.g. SIMATIC PC/PG Image Partition Creator). The ISA bus is disabled when this option is set.
Detailed descriptions 17.6 BIOS setup "I/O device configuration" submenu Figure 17-11 COM/LPT configuration submenu The resources used by an interface are released when you disable the interface in question. The I/O addresses and interrupts are pre-assigned; it is advisable not to change these default assignments. Internal printer port LPT1 Mode: Use this setting to set the operating mode of the printer port.
Detailed descriptions 17.
Detailed descriptions 17.6 BIOS setup "PCI Devices" field If the PCI devices field is selected, the following submenu appears: Figure 17-13 PCI devices submenu, slot #1 ROM scan option: Enable master Latency timer [Enabled] The ROM option of the PCI module (if present) is enabled [Disabled] The ROM option of a PCI module is disabled.
Detailed descriptions 17.
Detailed descriptions 17.
Detailed descriptions 17.6 BIOS setup 17.6.6 Security menu You can only edit the fields enclosed in square brackets. Two passwords can be assigned to protect your PC from unauthorized use. The Supervisor password can be used to restrict usage of the hard disk.
Detailed descriptions 17.6 BIOS setup User password is Disabled The password is disabled. Enabled Certain Setup fields are thus configurable by the user, including the user password. The field resets automatically from [Disabled] to [Enabled] when the password is entered. Set supervisor password This field opens the dialog box for entering a password. Once it has been entered, the supervisor password can be changed or deleted by pressing ”Return” and thus deactivated.
Detailed descriptions 17.6 BIOS setup 17.6.7 Power menu This menu has the following layout. Figure 17-17 "Power" menu (Example) The Power menu offers a number of power saver modes for environmentally friendly computing: Power Savings Hard Disk Timeout [Disabled] no energy-saving functions [Customized, Maximum Power Savings, Maximum Performance] freely selectable or default values for min./max. energy saving functions.
Detailed descriptions 17.6 BIOS setup 17.6.8 Boot menu This menu allows you to assign a priority for the boot devices. Figure 17-18 Boot Menu 1)Intel® UNDI, PXE-2.0 is only displayed if, beforehand, the Wake on LAN boot function has been set to "Enabled" in the hardware options menu. This menu lists the boot devices in groups. The group with the highest priority is at the top. To change the sequence: Select the group with the ↑↓ keys, move to the desired position with + or -.
Detailed descriptions 17.6 BIOS setup Figure 17-19 Boot menu (example) This screen shows all possible boot devices. The device taking highest priority is listed in the first line of the relevant group. Here again, you can change the order of appearance as described above. If a boot device is not available, the next device in the sequence is automatically checked to ascertain whether or not it is bootable.
Detailed descriptions 17.6 BIOS setup 17.6.9 Version menu This menu contains the information you will have to quote when you send us technical questions about your system.
Detailed descriptions 17.6 BIOS setup 17.6.10 Exit menu The setup program is always closed from this menu. Figure 17-21 Exit menu Save Changes & Exit All changes are saved; a system restart is carried out with the new parameters. Discard Changes & Exit All changes are discarded and the system performs a restart based on the old parameters. Get Default Values All parameters are set to safe values. Load Previous Values The last saved values are reloaded. Save Changes Save all Setup settings.
Detailed descriptions 17.6 BIOS setup 17.6.11 BIOS setup default settings Documenting your device configuration If you have changed any default settings in Setup, you can enter them in the following table. You can then refer to these entries for any future hardware modifications. Note Print out the table below and keep the pages in a safe place once you made your entries.
Detailed descriptions 17.6 BIOS setup Keyboard Features Numlock On Key Click Disabled Keyboard auto-repeat rate 30/sec Keyboard auto-repeat delay ½ sec Hardware Options PCI-MPI/DP Enabled On-board Ethernet 1 Enabled Onboard Ethernet 1 Address 08000624xxxx On-board Ethernet 1 Remote Boot Disabled On-board Ethernet 2 Enabled Onboard Ethernet 2 Address 08000624xxxx On-board Ethernet 2 Remote Boot Disabled SafeCard functions Enabled Fan Control Enabled CRT / LCD selection Simultan.
Detailed descriptions 17.6 BIOS setup SATA/PATA Configuration PATA Controller: Enabled SATA Controller mode Enhanced AHCI Configuration Disabled RAID support Disabled Security Supervisor Password Is Disabled User Password is Disabled Set User Password Enter Set Supervisor Password Enter Password on boot Disabled Fixed disk boot sector Standard Boot Boot priority order: Excluded from boot order: Version 17-68 SIMATIC PC SIMATIC BoxPC627/ PanelPC677 BIOS Version L05.01.00.
A A Appendix A.1 A.1.1 A.1 Certificates and guidelines Guidelines and declarations Notes on the CE marking The following applies to the SIMATIC product described in this documentation: EMC directive AC voltage supply The devices with AC voltage supply fulfill the requirements of the EC directive "89/336/EEC Electromagnetic Compatibility" and are intended for the following fields of application in accordance to the CE marking.
Appendix A.1 Certificates and guidelines Caution This is a system of Class A. The equipment may cause RF interference in residential areas. In this case, the operating company may be held liable for taking appropriate measures. Low-voltage directive The devices with AC power pack complies with the requirements of EC directive 73/23/EEC (Low-Voltage Guidelines). Compliance has been verified by a test in accordance with the EN 60950-1 standard.
Appendix A.1 Certificates and guidelines A.1.2 Certificates and approvals DIN ISO 9001 certificate The quality assurance system for the entire product process (development, production, and marketing) at Siemens fulfills the requirements of ISO 9001 (corresponds to EN 29001: 1987). This has been certified by DQS (the German society for the certification of quality management systems). EQ-Net certificate no.
Appendix A.1 Certificates and guidelines EMC USA Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Appendix A.1 Certificates and guidelines A.1.3 Electrostatic charging of individuals Anyone who is not connected to the electrical potential of their surroundings can be electrostatically charged. The figure below shows the maximum electrostatic voltages that can accumulate in a person who is operating equipment when he/she comes into contact with the materials indicated. These values comply with the specifications of IEC 801–2. Figure A-1 Electrostatic voltages with which an operator can be charged.
Appendix A.2 Additional support A.2 A.2 Additional support Do you have additional questions regarding use of the described products, which are not answered in the documentation? Then, contact the Siemens representative or office nearest you. • Your Siemens representative: "http://www.siemens.com/automation/partner" • Access to available technical documentation for individual SIMATIC products and systems: "http://www.siemens.
B ESD directives B.1 B.1 B ESD guideline What does ESD mean? Almost all electronic modules are equipped with highly integrated components and elements in MOS technology. For technological reasons, these electronic components are very sensitive to overvoltages and, consequently, to electrostatic discharge.
B ESD directives B.1 B.1 ESD guideline Precautions against electrostatic discharge Most plastics can be charged easily. Therefore, keep plastics away from ESD components! When working with electrostatically sensitive components, make sure that the person, the workstation and the packaging are properly grounded. Conduct the electrostatic charge away from your body by touching the mounting plate for the interfaces, for example.
C List of abbreviations / acronyms C.1 C.
List of abbreviations / acronyms C.
Glossary ATAPI CD–ROM Drive AT-Bus Attachment Packet Interface (connected to AT bus) CD-ROM drive Automation device (AG) The programmable logical controllers (PLC) of the SIMATIC S5 system consist of a central controller, one or more CPUs, and various other modules (e.g. I/O modules). Automation system (AS) The programmable logical controllers (PLC) of the SIMATIC S7 system consist of a central controller, one or more CPUs, and various I/O modules.
Glossary Cache High-speed access buffer for interim storage (buffering) of requested data. CE marking Communauté Européene The CE symbol confirms the conformance of the product with all applicable EC directives, e.g. the EMC directive. Chipset Located on the motherboard, connects the processor with the RAM, the graphic controller, the PCI bus, and the external interfaces. Cold start A start sequence, starting when the computer is switched on.
Glossary Device configuration The configuration of a PC or programming device contains information on hardware and device options, such as memory configuration, drive types, monitor, network address, etc. The data are stored in a configuration file and enable the operating system to load the correct device drivers and configure the correct device parameters. . If changes are made to the hardware configuration, the user can change entries in the configuration file using the SETUP program. .
Glossary Gender changer Using the gender changer (25-pin / 25-pin), the COM1/V24/AG interface of the SIMATIC PC family can be converted to the usual 25-pin male connector. Hard disks Hard disks represent a form of magnetic disk storage medium (Winchester drives, hard disks) with integrated magnetic disks. Hot swapping The SATA interface gives the device's hard drive system hot-swap capability.
Glossary LAN Local Area Network: LAN is a local network that consists of a group of computers and other devices that are distributed across a relatively restricted range and are linked with communication cables. The devices connected to a LAN are called nodes. The purpose of networks is the mutual use of files, printers or other resources. Legacy USB support Support of USB devices (e.g. mouse, keyboard) on the USB ports without driver.
Glossary Operating system Summarizing term describing all functions for program execution, allocation of system resources to the various user programs, and for controlling and monitoring consistency of the operating mode in cooperation with the hardware (e.g. Windows XP Professional). Packet writing The CD-RW is used as a diskette medium. The CD can then be read only by packet–writing compatible software or has to be finalized. Finalization of a CD closes the CD within an ISO9660 shell.
Glossary Pixel PixElement (picture point). The pixel represents the smallest element that can be reproduced on-screen or on a printer. Plug&Play Generally, a reference to the ability of a computer to automatically configure the system for communication with peripheral devices (for example monitors, modems or printers). The user can plug in a peripheral and ”play” it at once without manually configuring the system. A Plug&Play PC requires both a BIOS that supports Plug&Play and a Plug&Play expansion card.
Glossary Restore DVD The Restore DVD is used to restore the system partition or the entire hard disk to factory state if the system has crashed. The bootable DVD contains all the necessary image files. You can also create a boot disk allowing restoration via the network. ROM Read-Only Memory ROM is a read-only memory in which every memory location can be addressed individually. The programs or data are permanently stored and are not lost in the event of a power failure.
Glossary Windows Microsoft Windows is a multitasking graphical user interface. Windows provides a standard graphical interface based on drop-down menus, windowed regions on the screen, and allows operation with a pointer device such as a mouse. WLAN Wireless LAN is a local network that transmits data via radio waves, infrared light or another wireless technology. Wireless LAN is mainly used in connection with mobile computers in the office or in factory environments.
Glossary Glossary-10 SIMATIC Panel PC 877 Operating instructions, Release 07/2006, A5E00877780-01
Index < key, 10-6 A Abbreviations, C-1 AC voltage supply, A-1 Accessories, 3-5 Advanced menu BIOS setup, 17-51 Alarms, 9-10, 9-11 Allocation PCI IRQ channels, 17-25 Approval, 1-1, 8-10, 15-6 Approvals, A-3 Area of application, 1-1 Arithmetic symbols, 10-7 Entering, 10-7 Assignment External interfaces, 17-5 I/O addresses, 17-32 Interrupts, 17-34 Memory addresses, 17-35 Authorization, 12-33 Automatic logon, 8-11, 8-12 Automatic updates, 9-10 B back up, 12-46 Hard disk drive, 12-46 Backlighting, 3-2,
Index On the key panel, 10-3 Control unit, 3-1, 3-2, 12-4, 15-6 Separating from the computer unit, 12-4 Convention, 1-2 couple, 7-3 Device, 7-3 Coupling with SIMATIC S7, 7-1 Cover foil, 3-5 Cursor key, 10-8 D Dash, 10-7 Data exchange, 7-1 Date, 17-41 BIOS setup, 17-41 DC power supply, A-1 Decimal point, 10-7 Defaults BIOS, 17-66 Degree of protection, 4-8 IP54 degree of protection, 4-8 IP65 degree of protection, 4-8 Design, 3-2, 4-6, 4-12, 12-3, 15-6 Bus board, 17-24 Centralized configuration, 12-3 Distrib
Index Measuring, B-2 modify.
Index Key code, 15-11 Key panel, 8-7, 10-3 set, 8-7 Keyboard, 3-2, 10-9 BIOS setup, 17-47 BIOS setup, 17-47 External keyboard, 10-9 Features, 17-47 Keyboard table, 15-11 Keyboard variant, 3-2 Knurled screw, 12-4 Memory addresses Assignment, 17-35 Memory configuration, 12-11 Memory expansion, 12-10, 12-11 Memory expansion, 12-10 Minus sign, 10-7 modify.
Index Operating status, 3-2, 10-1 Operating system, 3-4, 12-35 Installing, 12-35 Windows 2000 Professional, 12-30, 12-37 Windows XP Professional, 12-30, 12-37 Output voltage, 15-9, 15-10 P Package contents, 4-2 Checking, 4-2 Packaging, 4-2 Checking, 4-2 Removing, 4-2 Panel PC, 12-4 Panel PC 877, 3-1, 16-2 Parallel interface, 17-8 BIOS setup, 17-54 Partitioning Windows 2000 Professional, 12-30 Windows XP Professional, 12-30 Password Boot, 17-60 Supervisor, 17-59 User, 17-60 PCI / AT cards Assignment of PCI
Index BIOS setup, 17-42 Security menu BIOS setup, 17-59 Selecting the language Windows XP, 9-16 Self test, 13-3 Self-test, 8-2, 9-2 Separating, 12-4, 12-6 Device, 12-4, 12-6 Serial interface, 17-2 BIOS setup, 17-54 Service pack, 8-11 Service Pack, 8-12 set, 8-5, 8-7, 9-6 Key panel, 8-7 Touch screen front, 8-5 Touch software, 9-6 Setting up partitions, 12-30 Shipping, B-2 ESD, B-2 Sign, 10-7 Entering, 10-7 SIMATIC S7, 7-1, 7-2, 17-30 Integration, 7-1 Slide-in labels, 3-5, 15-5 slot, 3-3 Softkey, 3-2, 10-14
Index Interface assignments, 17-9 Interfaces, 17-2 Technical data, 15-3 USB interface, 3-2, 10-3, 10-16 USB mouse, 10-16 USB peripheral, 8-13 User password, 17-60 V Versions Menu BIOS Setup, 17-64 VGA, 3-3 Virus protection, 9-10 visualizing, 12-11 Memory expansion, 12-11 W Warranty, 2-4 Watchdog Monitoring function, 11-5 Monitoring times, 11-5 Weight, 15-5, 15-6 Windows 2000 Professional Partitioning the hard disk, 12-30, 12-37 Windows XP Selecting the language, 9-16 Windows XP Professional Partitioning
Siemens AG Automation and Drives Industrial Automation Systems Postfach 4848 90437 NUERNBERG Federal Republic of Germany www.siemens.
