User Manual

ManualsBrandsSiemens ManualsCommunication devices (excl. controller)LPB-lcompatible Temperature Sensor/Adapt QAB30.600

CE1N2528en

09.05.2000

6LHPHQV%XLOGLQJ7HFKQRORJLHV

/DQGLV6WDHID'LYLVLRQ





/3%FRPSDWLEOH

7HPSHUDWXUH6HQVRU

$GDSWHU

4$%

7HPSHUDWXUHVHQVRUDGDSWHUIRUXVHLQFRQQHFWLRQZLWKWKH2&,

FRPPXQLFDWLRQFHQWUH

• 7HPSHUDWXUHPHDVXUHPHQWZLWKWKHUHDG\FRQQHFWHGLPPHUVLRQWHPSHUDWXUH

VHQVRU

• &RQQHFWLRQIDFLOLW\IRUDVHFRQGWHPSHUDWXUHVHQVRU

• 0HDVXUHGYDOXHWUDQVPLVVLRQYLD/3%/RFDO3URFHVV%XV

8VH

The QAB30.600 provides supervision of the immersion temperature sensor that is

ready connected to the unit and of an optional second temperature sensor.

The OCI600 communication centre periodically retrieves the measured temperature

values from the QAB30.600 via LPB.

On the OCI600, the maximum and minimum limit value can be defined for each

temperature measured. If a limit value is crossed, the OCI600 can deliver alarms (to a

PC / printer, fax, mobile phone, pager or Minitel).

Summary of content (6 pages)

PAGE 1
/3% FRPSDWLEOH 7HPSHUDWXUH 6HQVRU $GDSWHU 4$% 7HPSHUDWXUH VHQVRU DGDSWHU IRU XVH LQ FRQQHFWLRQ ZLWK WKH 2&, FRPPXQLFDWLRQ FHQWUH • 7HPSHUDWXUH PHDVXUHPHQW ZLWK WKH UHDG\ FRQQHFWHG LPPHUVLRQ WHPSHUDWXUH VHQVRU • &RQQHFWLRQ IDFLOLW\ IRU D VHFRQG WHPSHUDWXUH VHQVRU • 0HDVXUHG YDOXH WUDQVPLVVLRQ YLD /3% /RFDO 3URFHVV %XV 8VH The QAB30.600 provides supervision of the immersion temperature sensor that is ready connected to the unit and of an optional second temperature sensor.
PAGE 2
7\SH VXPPDU\ When ordering, please give the relevant type references: 7\SH RI XQLW 7\SH UHIHUHQFH Temperature sensor / adapter 4$% Protection pocket for attached immersion temperature sensor suited for nominal pipe sizes DN20...40 $/7 Protection pocket for nominal pipe sizes DN50...80 $/7 Address plug set for bus addressing covering the address range from 97 to 128 37* The scope of delivery of the QAB30.
PAGE 3
0HFKDQLFDO GHVLJQ The QAB30.600 temperature sensor / adapter consists of the unit itself and the ready connected immersion temperature sensor. 8QLW The unit consists of base, terminal block and cover. To facilitate wall mounting, the base has three holes. DIN rail mounting is made possible by a snap-on facility at the rear.
PAGE 4
(QJLQHHULQJ QRWHV 2SHUDWLQJ YROWDJH The operating voltage of AC 24 V is supplied by an isolating transformer which also powers the OCI600 communication centre(s) and the AEW2.1 pulse adapters. When sizing the transformer, the power consumption of all units connected to the AC 24 V power supply must be taken into consideration. %XV SRZHU VXSSO\ The temperature sensor / adapter has QRWKLQJ to do with the bus power supply.
PAGE 5
&RQQHFWLRQ WHUPLQDOV Connection terminals used: B1 B4 M G1, G2 MB DB Ready connected immersion temperature sensor Optional Ni1000 sensor Ground Operating voltage AC 24 V Ground bus Data bus &RQQHFWLRQ GLDJUDP G1 % AC 24 V B1 M G1 G2 MB DB B M % B4 M 8 G2 G1 DB MB 1 G2 B1 B2 N1 U1 Ready connected immersion temperature sensor Optional Ni1000 sensor OCI600 communication centre QAB30.600 temperature sensor / adapter 5/6 Siemens Building Technologies Landis & Staefa Division QAB30.
PAGE 6
'LPHQVLRQV 61 75 2 27 16 27 37 37 2851M01 Pg11 1500 0LQLPXP FOHDUDQFH 3LSH A DN L = 50 mm 3URWHFWLRQ SRFNHW $/7 6OHHYH Outside dia. $ Type ref. Immersion length 7 Length / DN20 ( /4") 26.9 mm $/7 22 mm 20 mm DN25 (1") 33.7 mm $/7 26 mm 16 mm DN32 (1 /4") 42.4 mm $/7 30 mm 12 mm DN40 48.3 mm $/7 30 mm 12 mm DN50 60.3 mm $/7 53 mm 20 mm DN65 76.1 mm $/7 53 mm 20 mm DN80 88.