Technical data

ManualsBrandsSiemens ManualsHousehold AppliancesREV-R.03/1

CE1N2214en

28.08.2008

Building Technologies

HVAC Products

214

REV200.03RF REV-R.03/1

REV200S.03RF REV-R.03S/1

REV200RF/SET

REV200SRF/SET

Room Temperature

Controller

REV200../SET

Backlit touch screen with integrated radio transmitter and receiver

(switching unit with relay outputs)

• Mains-independent room temperature controller

• Easy-to-understand, self-explanatory touch screen

• Self-learning 2-position controller with PID control (patented)

• Choice of 3 different 24-hour operating modes and one 7-day mode including

individually adjustable 24-hour modes

• Control of cooling equipment

• Advantageous for retrofitting and upgrading projects (wireless room unit)

Use

Room temperature control in:

• apartments, single-family or holiday houses

• offices, individual rooms and consulting rooms or commercially used spaces

For the control of the following pieces of equipment:

• Solenoid valves of an instantaneous water heater

• Solenoid valves of an atmospheric gas burner

• Forced draft gas and oil burners

• Heating pumps, zone valves (normally closed)

• Electric direct heating systems or fans of an electric storage heater

• Thermic actuators

• Cooling and refrigeration equipment

Summary of content (15 pages)

PAGE 1
2 REV200.03RF REV200S.03RF 214 REV-R.03/1 REV-R.03S/1 REV200RF/SET REV200SRF/SET Room Temperature Controller REV200..
PAGE 2
Functions • • • • • • • • • • • • Radio signal transmission PID control with a self-learning or selectable switching cycle Automatic operation with 7-day program 3 different 24-hour modes Remote control and override button Sensor calibration, reset function Locking of display to facilitate cleaning and to prevent tampering Frost protection function, minimum limitation of the setpoint Holiday mode Cooling Pump kick Optimum start for the first heating period (P.
PAGE 3
Parameter settings Pure 2-position control with a switching differential of 0.5 °C (±0.25 °C) for very difficult controlled systems with considerable outside temperature variations. The control algorithm is selected with DIP switches no. 1 and no. 2. All basic settings are made with a number of DIP switches. The DIP switches can be accessed by removing the unit from its base. Every DIP switch setting must be confirmed by pressing the DIP switch button, thus activating the setting.
PAGE 4
Example with 2 switching cycles: °C 22 20 18 08 10 18 22 h 2212Z01 16 7-day program The 7-day program offers different switching patterns for every day of the week. This means that one of the three 24-hour switching patterns can be selected differently for every day of the week, depending on the requirements. Like with the 24-hour program, time and setpoint of every switching point can be different.
PAGE 5
Cooling DIP switch no. 4 is used for switching over to cooling mode when used in cooling applications. Periodic pump run The setting is made with DIP switch no. 5 while the pump is running. This protects the pump against seizure during longer OFF periods. Periodic pump run is activated for one minute every 24 hours at 12:00 h. Setpoints In the automatic modes, the setpoints can be entered for every switching point, and individually in the continuous modes.
PAGE 6
Display and operating elements Display check Temperature values and symbols Button displays Normal temperature Economy temperature Standby with frost protection Time of day or switching time Change batteries Display symbols Bumer in operation Locking of display active Holiday program active ... Temperature setpoint number of switching program Display button (with display of the current day) Cooling function activated ...
PAGE 7
Automatic storage When an adjustable display button is touched, the displayed value will automatically be stored 5 seconds later and the display returns to the initial operating mode. The same action is achieved when touching the button again. Adjusting the values Pressing one of these buttons for less than one second produces a step of one minute (time settings) or of 0.2 °C (temperature settings).
PAGE 8
• If the room temperature displayed does not agree with the room temperature effectively measured, the temperature sensor should be recalibrated (refer to « Sensors Calibration » page 4). Wall mounting of controller / transmitter REV200.03RF REV200S.03RF • The unit can be fitted to most commercially available recessed conduit boxes or directly on the wall • Mounting height is approximately 1.5 m above the floor • When installing the controller, the base must first be fitted.
PAGE 9
Commissioning controller/transmitter REV200… and receiver REV-R.03/1 REV-R.03S/1 LED_1 (green / red): Indication for - Signal strength - Receiver linked to cotroller/transmitter LED_2 (orange): Indication for - Learning mode - Telegram reception - Status of relais contact Test telegram SET button Learning telegram RESET button 1. Switch on REV200… • Remove the battery transit tab: As soon as the battery transit tab is removed, the unit starts to operate. 2. Mount REV-R.03/1 REV-R.
PAGE 10
LED_1 flashes green: We distinguish between three signal strengths: Very good (flashes 3x), Good (flashes 2x) and Satisfactory (flashes 1x). As soon as LED_1 flashes in green, link between REV200…and REV-R… is basically ok. g) Move REV-R… within an area of approximately 1 square meter to find location of best RF reception. Always observe LEDs from a distance of 2…3 meters. To get a durable link, we recommend to site REV-R… at a location where signal strength is at least “Good”. 6.
PAGE 11
7. Finishing mounting of REV-R… a) b) c) d) e) Switch off power Mark location where REV-R… is currently fixed If necessary loosen wiring Mount receiver at location marked before, wire completely and close housing Switch on mains power Notes • • In the event of a power failure at the REV-R…, the relay will be deenergized. If in normal operation REV-R… does receive for more than 25 minutes a very weak or no control telegram from REV200…, LED_1 starts to flash in red.
PAGE 12
Technical data REV200…RF General unit data General data transmitter Standards Environmental conditions Weight Color Seize Operating voltage Batteries (alkaline AA) 2 x 1.
PAGE 13
Technical data receiver REV-R… Operating voltage Power Frequency Switching capacity of relays Voltage Current Environmental conditions Operation Climatic conditions Temperature Humidity Storage and transport Climatic conditions Temperature Humidity Mechanical conditions conformity Norms and EMC directives standards Low-voltage directives R&TTE directives Product safety Radio equipment Automatic electrical controls for household and similar use Special requirements placed on energy controllers Electromagneti
PAGE 14
Connection diagram receiver REV-R… Lx L Lx N L2 L1 N2 L N Lx L1 AC 24...250 V AC 230 V L Live conductor, AC 230 V Neutral conductor, AC 230 V Live, AC 24...250 V N.O. contact, AC 24...250 V / 6 (2.5) A N.C. contact, AC 24...250 V / 6 (2.
PAGE 15
Dimensions 130 2212M02 Controller / transmitter REV200…RF 25 60 110 56 20.5 83,5 2212M01 33 14 Receiver REV-R… 84 2265M01 32 2265M02 60 104 60 ©2007-2008 Siemens Switzerland Ltd. Building Technologies HVAC Products Subject to alteration REV200…RF room temperature controller 15/15 CE1N2214en 28.08.