Operation Manual

ManualsBrandsSiemens ManualsTemperature ControllerSiemens REV23

Siemens Building Technologies/HVAC Products - REV23 1.04.05 1/3

Set Time and day of programmer

T - Set T T Temp.

Set time for ON/OFF in the Auto Mode.

1 time period. e.g. ON 0700 OFF 2300.

2 time periods. e.g. ON 0600 OFF 0900, ON 1700 OFF 2200.

3 time periods. e.g. ON 0600 OFF 0800, ON 1100 OFF 1300,

ON 1700 OFF 2200.

Temperatures for T are also set in this setting.

T Temp will be on when Time Periods are off. Setting can be seen

on 24hr clock at bottom of screen.

Holiday Mode - SET No. # of days you will be gone and T temp. while away.

Operating Instructions REV23

Auto Mode - Runs according to the times which have been programmed

into REV (See Set Points) It will follow the heating periods of T and T .

Economy Mode/MAN will stay on T temp for 24 hours x 7 days or until another

mode has been selected.

OFF/ Frost protection for Hydronic floor systems. Factory Set 5 C.

Programmed Timed override. Unit will Run at T from the start of 1st time

period to the end of the last time period.

Selects between Run Modes - , , , and .

Can temporarily increase or decrease Set Point temps for T or T . It will

revert back to original Set Point after a change in Run Modes or a Time Period.

- This can be used in all 5 modes. 4.0 C

Override button selects between T & T in & modes.

Will control for programmed days away at T Set temp.

Scroll Button. Selects Programming Mode. Click down on roller to get in, and

roll to change time, temp. and program settings.

Press ESC to get out of Program Mode and into Run Mode or simply don't touch

the scroll button for 20 seconds.

Comfort Mode/MAN will stay on T temp for 24 hours x 7 days or until another

mode has been selected.

AUTO

REV23 Thermostats can be operated in 5 different modes:

AUTO

(At home during the day.)

To Program Mode:

Esc

AUTO

Summary of content (4 pages)

PAGE 1
REV23 Operating Instructions REV23 Thermostats can be operated in 5 different modes: 1) AUTO Auto Mode - Runs according to the times which have been programmed into REV (See Set Points) It will follow the heating periods of T and T . 2) Comfort Mode/MAN will stay on T mode has been selected. temp for 24 hours x 7 days or until another 3) Economy Mode/MAN will stay on T mode has been selected. temp for 24 hours x 7 days or until another 4) OFF/ Frost protection for Hydronic floor systems.
PAGE 2
To Program 1-7 T Time/Day of the week (must be done) Click roller down, scroll roller until " " starts to flash. Click roller down, scroll roller to set hours. e.g. 13 Click roller down, scroll roller to set minutes. e.g. 15 Click roller down, will be flashing, scroll to put correct 1 2 day. e.g. Monday Tue, etc. Press escape time and day are now set. Program T ,T and T temperatures. Click roller down, scroll roller till "T" starts to flash. Click roller down, scroll roller till "T : starts to flash.
PAGE 3
REV23 Screen Features Programming Modes Days of the week Indicates heating "ON" Low battery Only used with Run Modes Telephone Interface Kit (TEL110-EN) Run Mode selector button Temperature Increase Temperature Decrease Override Button Indicates T Temp. ON Indicates T Temp. ON 24 Hour Clock Scroll Button (Programming Only) Return to run mode Esc For further info. on REV23, please refer to data sheet no. 2264.
PAGE 4
REV Thermostat Operating Tips Always look at the bottom of the screen at the 24hr clock to see what time the thermostat is programmed to come on and off. You can then instantly see if your heater should be on either temp or temp. If the heating is not on when the time clock indicates that it should check to see that the time is set correctly. (see programming sheet) EXAMPLE and is programmed for 2 time periods. The above 24 hour time clock is running in temp.