System Manual
Table Of Contents
- SIMATIC RF200
- Legal information
- Table of contents
- 1 Introduction
- 2 Safety notes
- 3 System overview
- 4 Planning the RF200 system
- 4.1 Fundamentals of application planning
- 4.1.1 Selection criteria for SIMATIC RF200 components
- 4.1.2 Transmission window and read/write distance
- 4.1.3 Width of the transmission window
- 4.1.4 Impact of secondary fields
- 4.1.5 Permissible directions of motion of the transponder
- 4.1.6 Operation in static and dynamic mode
- 4.1.7 Dwell time of the transponder
- 4.1.8 Communication between communication module, reader and transponder
- 4.2 Field data of transponders and readers
- 4.3 Installation guidelines
- 4.4 Chemical resistance of the reader and transponders
- 4.5 Further information
- 4.1 Fundamentals of application planning
- 5 Readers
- 5.1 SIMATIC RF210R
- 5.2 SIMATIC RF210M
- 5.3 SIMATIC RF220R
- 5.4 SIMATIC RF240R
- 5.5 SIMATIC RF250R
- 5.6 SIMATIC RF260R
- 5.7 SIMATIC RF280R
- 5.8 SIMATIC RF285R
- 5.9 SIMATIC RF290R
- 6 Antennas
- 7 Transponder
- 7.1 Memory configuration of ISO the transponders
- 7.2 MDS D100
- 7.3 MDS D117
- 7.4 MDS D124
- 7.5 MDS D126
- 7.6 MDS D127
- 7.7 MDS D139
- 7.8 MDS D160
- 7.9 MDS D165
- 7.10 MDS D200
- 7.11 MDS D261
- 7.12 MDS D324
- 7.13 MDS D339
- 7.14 MDS D400
- 7.15 MDS D421
- 7.16 MDS D422
- 7.17 MDS D423
- 7.18 MDS D424
- 7.19 MDS D425
- 7.20 MDS D426
- 7.21 MDS D428
- 7.22 MDS D460
- 7.23 MDS D521
- 7.24 MDS D522
- 7.25 MDS D522 special variant
- 7.26 MDS D524
- 7.27 MDS D525
- 7.28 MDS D526
- 7.29 MDS D528
- 7.30 MDS D560
- 8 System integration
- 9 System diagnostics
- A Appendix
Antennas
6.4 ANT 8
SIMATIC RF200
210 System Manual, 03/2019, J31069-D0227-U001-A11-7619
6GT2398-1CF10
6GT2398-1CF00
Permitted ambient conditions
Ambient temperature
• During operation • -25 ... +70 °C
• During transportation and storage • -40 ... +85 °C
Degree of protection to EN 60529
IP67
Shock-resistant according to EN 60721-3-7 Class
7 M2
1)
500 m/s
2
Vibration-resistant according to EN 60721-3-7
Class 7 M2
1)
200 m/s
2
Design, dimensions and weight
Dimensions (∅ x thread x L)
M8 x 1 x 38 mm
Weight 10 g without cable
140 g with cable
Type of mounting
2x stainless steel nuts M8 x 1
Cable length
3 m
1)
Warning: The values for shock and vibration are maximum values and must not be applied contin-
uously.
6.4.7 Dimension drawing
①
The antenna connector may only be tightened by hand.
②
The cable must be secured in front of/behind the support sleeve so that no bending strain can
be transferred to the antenna connector.
Figure 6-19 Dimension drawing ANT 8 (all values in mm)