System Manual
Table Of Contents
- SIMATIC RF200
- Legal information
- Table of contents
- 1 Introduction
- 2 Safety notes
- 3 System overview
- 4 Planning the RF200 system
- 4.1 Fundamentals of application planning
- 4.1.1 Selection criteria for SIMATIC RF200 components
- 4.1.2 Transmission window and read/write distance
- 4.1.3 Width of the transmission window
- 4.1.4 Impact of secondary fields
- 4.1.5 Permissible directions of motion of the transponder
- 4.1.6 Operation in static and dynamic mode
- 4.1.7 Dwell time of the transponder
- 4.1.8 Communication between communication module, reader and transponder
- 4.2 Field data of transponders and readers
- 4.3 Installation guidelines
- 4.4 Chemical resistance of the reader and transponders
- 4.5 Further information
- 4.1 Fundamentals of application planning
- 5 Readers
- 5.1 SIMATIC RF210R
- 5.2 SIMATIC RF210M
- 5.3 SIMATIC RF220R
- 5.4 SIMATIC RF240R
- 5.5 SIMATIC RF250R
- 5.6 SIMATIC RF260R
- 5.7 SIMATIC RF280R
- 5.8 SIMATIC RF285R
- 5.9 SIMATIC RF290R
- 6 Antennas
- 7 Transponder
- 7.1 Memory configuration of ISO the transponders
- 7.2 MDS D100
- 7.3 MDS D117
- 7.4 MDS D124
- 7.5 MDS D126
- 7.6 MDS D127
- 7.7 MDS D139
- 7.8 MDS D160
- 7.9 MDS D165
- 7.10 MDS D200
- 7.11 MDS D261
- 7.12 MDS D324
- 7.13 MDS D339
- 7.14 MDS D400
- 7.15 MDS D421
- 7.16 MDS D422
- 7.17 MDS D423
- 7.18 MDS D424
- 7.19 MDS D425
- 7.20 MDS D426
- 7.21 MDS D428
- 7.22 MDS D460
- 7.23 MDS D521
- 7.24 MDS D522
- 7.25 MDS D522 special variant
- 7.26 MDS D524
- 7.27 MDS D525
- 7.28 MDS D526
- 7.29 MDS D528
- 7.30 MDS D560
- 8 System integration
- 9 System diagnostics
- A Appendix
System diagnostics
9.1 Error codes of the RF200 readers
SIMATIC RF200
410 System Manual, 03/2019, J31069-D0227-U001-A11-7619
Table 9- 1 Error codes of the RF200 readers
Flashing of
red LED on
reader
Error code
(hex)
Description
00
0x00
no error
02 0x01 Presence error, possible causes:
• The active command was not carried out completely
• The transponder left the antenna field while the command was
being processed - communication disruption between reader and
transponder
05 0x05 Parameterization error, possible causes:
• Unknown command
• Incorrect parameter
• Function not allowed
06
0x06
Air interface faulty
12 0x0C The transponder memory cannot be written, possible cause:
Hardware fault (memory faulty)
13 0x0D Error in the specified memory address (access attempted to non-
existent or non-accessible memory areas).
19 0x13 Buffer overflow: Insufficient buffer available in the reader for saving
the command
20
0x14
Major system fault (hardware fault)
21
0x15
Parameter assignment error: faulty parameter in RESET command
24
0x18
Only a RESET command is permitted
25
0x19
Previous command is still active
28
0x1C
Antenna is already switched off/Antenna is already switched on
30
0x1E
Incorrect number of characters in frame
Note
Error message when memory area is protected
For transponders with a locked or protected memory area, different error messages can
occur following a write command depending on the data carrier type, e.g. MDS D1xx (NXP),
D3xx (Infineon), D4xx (Fujitsu): Error 01, 0C