System Manual
Table Of Contents
- SIMATIC RF200
- Legal information
- Table of contents
- 1 Introduction
- 2 Safety notes
- 3 System overview
- 4 Planning the RF200 system
- 4.1 Fundamentals of application planning
- 4.1.1 Selection criteria for SIMATIC RF200 components
- 4.1.2 Transmission window and read/write distance
- 4.1.3 Width of the transmission window
- 4.1.4 Impact of secondary fields
- 4.1.5 Permissible directions of motion of the transponder
- 4.1.6 Operation in static and dynamic mode
- 4.1.7 Dwell time of the transponder
- 4.1.8 Communication between communication module, reader and transponder
- 4.2 Field data of transponders and readers
- 4.3 Installation guidelines
- 4.4 Chemical resistance of the reader and transponders
- 4.5 Further information
- 4.1 Fundamentals of application planning
- 5 Readers
- 5.1 SIMATIC RF210R
- 5.2 SIMATIC RF210M
- 5.3 SIMATIC RF220R
- 5.4 SIMATIC RF240R
- 5.5 SIMATIC RF250R
- 5.6 SIMATIC RF260R
- 5.7 SIMATIC RF280R
- 5.8 SIMATIC RF285R
- 5.9 SIMATIC RF290R
- 6 Antennas
- 7 Transponder
- 7.1 Memory configuration of ISO the transponders
- 7.2 MDS D100
- 7.3 MDS D117
- 7.4 MDS D124
- 7.5 MDS D126
- 7.6 MDS D127
- 7.7 MDS D139
- 7.8 MDS D160
- 7.9 MDS D165
- 7.10 MDS D200
- 7.11 MDS D261
- 7.12 MDS D324
- 7.13 MDS D339
- 7.14 MDS D400
- 7.15 MDS D421
- 7.16 MDS D422
- 7.17 MDS D423
- 7.18 MDS D424
- 7.19 MDS D425
- 7.20 MDS D426
- 7.21 MDS D428
- 7.22 MDS D460
- 7.23 MDS D521
- 7.24 MDS D522
- 7.25 MDS D522 special variant
- 7.26 MDS D524
- 7.27 MDS D525
- 7.28 MDS D526
- 7.29 MDS D528
- 7.30 MDS D560
- 8 System integration
- 9 System diagnostics
- A Appendix
Appendix
A.2 Accessories
SIMATIC RF200
System Manual, 03/2019, J31069-D0227-U001-A11-7619
423
NOTICE
Restriction to the approval of the wide-range power supply
Alterations to the SIMATIC RFID modules and devices as well as the use of SIMATIC RFID
components with third-party RFID devices are not permitted.
Failure to observe this requirement shall constitute a revocation of the radio equipment
approvals, CE approval and manufacturer's warranty. Furthermore, the compliance to any
salient safety specifications of VDE/DIN, IEC, EN, UL and CSA will not be guaranteed.
Safety notes for the US and Canada
The readers of the SIMATIC RF600 series may only be operated with the wide range power
supply unit for SIMATIC RF systems - as an optional component – or with power supply units
that are UL-listed in combination with the safety standards specified below:
● UL 60950-1 - Information Technology Equipment Safety - Part 1: General Requirements
● CSA C22.2 No. 60950 -1 - Safety of Information Technology Equipment
NOTICE
Warranty
The compliance of the SIMATIC RFID systems to the safety standards mentioned above
and the conditions in the UL approval will not be guaranteed if neither the wide-range
power supply unit for SIMATIC RF systems nor power supplies listed according to the
safety standards named are used.
A.2.2.5 Mounting & connecting
The wide-range power supply unit for SIMATIC RF systems is sold with a country-specific
power cable for EU, UK and US.
Note
Country-specific adaptation of the connector
When necessary, the primary cable can be adapted to country
-specific conditions. The
connector can be replaced by a country
-specific connector.
If you do this, make sure that the protective conductor is connected in the connector and that
grounding is ens
ured. If the protective conductor cannot be connected through the plug, you
must connect the grounding connection to the mounting hole
④ provided by the metal shoe.