System Manual
Table Of Contents
- SIMATIC RF200
- Legal information
- Table of contents
- 1 Introduction
- 2 Safety notes
- 3 System overview
- 4 Planning the RF200 system
- 4.1 Fundamentals of application planning
- 4.1.1 Selection criteria for SIMATIC RF200 components
- 4.1.2 Transmission window and read/write distance
- 4.1.3 Width of the transmission window
- 4.1.4 Impact of secondary fields
- 4.1.5 Permissible directions of motion of the transponder
- 4.1.6 Operation in static and dynamic mode
- 4.1.7 Dwell time of the transponder
- 4.1.8 Communication between communication module, reader and transponder
- 4.2 Field data of transponders and readers
- 4.3 Installation guidelines
- 4.4 Chemical resistance of the reader and transponders
- 4.5 Further information
- 4.1 Fundamentals of application planning
- 5 Readers
- 5.1 SIMATIC RF210R
- 5.2 SIMATIC RF210M
- 5.3 SIMATIC RF220R
- 5.4 SIMATIC RF240R
- 5.5 SIMATIC RF250R
- 5.6 SIMATIC RF260R
- 5.7 SIMATIC RF280R
- 5.8 SIMATIC RF285R
- 5.9 SIMATIC RF290R
- 6 Antennas
- 7 Transponder
- 7.1 Memory configuration of ISO the transponders
- 7.2 MDS D100
- 7.3 MDS D117
- 7.4 MDS D124
- 7.5 MDS D126
- 7.6 MDS D127
- 7.7 MDS D139
- 7.8 MDS D160
- 7.9 MDS D165
- 7.10 MDS D200
- 7.11 MDS D261
- 7.12 MDS D324
- 7.13 MDS D339
- 7.14 MDS D400
- 7.15 MDS D421
- 7.16 MDS D422
- 7.17 MDS D423
- 7.18 MDS D424
- 7.19 MDS D425
- 7.20 MDS D426
- 7.21 MDS D428
- 7.22 MDS D460
- 7.23 MDS D521
- 7.24 MDS D522
- 7.25 MDS D522 special variant
- 7.26 MDS D524
- 7.27 MDS D525
- 7.28 MDS D526
- 7.29 MDS D528
- 7.30 MDS D560
- 8 System integration
- 9 System diagnostics
- A Appendix
Appendix
A.2 Accessories
SIMATIC RF200
System Manual, 03/2019, J31069-D0227-U001-A11-7619
429
6GT2898-0ACx0
Design, dimensions and weights
Dimensions (L × W × H)
• Without plug • 140 × 85 × 35 mm
• With plug • 172.7 × 85 × 35 mm
Weight
720 g
Technical specifications of the input
Rated input voltage U
in
100 to 240 VAC
Input frequency f
in
50/60 Hz
Radio interference level
EN 55011/B
Switching frequency f
sw
approx. 70 kHz typ.
Connector type 7/8", 2-pin + PE
6 ... 8 mm
Technical specifications of the outputs
Output voltage tolerance ∆U
out
U
out nom
≤ +2 % / -1 %
at U
in
= 230 VAC, f = 50 Hz
Overvoltage protection
U
out nom
+20 % typ.
Noise ∆U
LF
≤ 1 % U
out
at U
in
= min., BW: 1 MHz
Noise ∆U
HF
≤ 2 % U
out
U
in
= min., BW: 20 MHz
Regulation
• Line regulation
• ≤ 1.0%
at U
in
= min./max.
• Load regulation
• ≤ 1.0%
at I
out
= 10...90...10%
Short-circuit current I
max
105 ... 130 % I
nom
at I
nom
= 3 A (+50 °C)
Settling time t
R
load variations < 5 ms
at I
out
= 10...90...10 %
Temperature coefficient ε 0.01 % / K
at T
A
= -25 °C ... +70 °C
Overload behavior P
over
Constant current
Short-circuit protection/
No-load response
Continuous/no-load stability
Derating 2 % / K
at T
A
> +50 °C ... +70 °C
Connector type M12, 4-pin
two sockets