SED2 VFD LON Interface Option Operating Instructions Item Number 125-3212, Rev.
SED2 VFD LON Interface Option Operating Instructions
NOTICE The information contained within this document is subject to change without notice and should not be construed as a commitment by Siemens Building Technologies, Inc. Siemens Building Technologies, Inc. assumes no responsibility for any errors that may appear in this document. All software described in this document is furnished under a license and may be used or copied only in accordance with the terms of such license.
Table of Contents Table of Contents How to Use this Manual................................................................................................1 Manual Organization..................................................................................................1 Manual Notations .......................................................................................................1 Where To Send Comments .......................................................................................
How to Use this Manual How to Use this Manual Manual Organization Section Provides: How to Use this Manual Organization of this manual, notations, and reference documents. LON Interface Option Overview Information and details about the LON Interface Option. Installation and Wiring LON Interface Option mounting and connection information. Startup Procedures Instructions to start up the LON Interface Option. Application Note Parameter settings for PID loop control via the LON Interface Option.
SED2 VFD LON Interface Option Operating Instructions LON Interface Option Overview General Description The LONMark® certified SED2 VFD LON Interface Option provides direct digital control of SED2 Variable Frequency Drives (VFDs). The SED2 VFD can reside on a LONWorks® network, enabling information sharing with all other LONMark products from multiple vendors. The SED2 VFD LON Interface Option is LONMark-compliant with Variable Speed Motor Drive Functional Profile Number 6010.
LON Interface Option Overview LON Interface Option Functionality The foundation of the SED2 VFD LON Interface Option is a Neuron 3120 processor, which manages the LON software functionality. The LON software functionality is based on LONMark Functional Profile Number 6010 for Variable Speed Motor Drives. In addition to the Standard Network Variable Types (SNVTs) of this Functional Profile, several others have been added: • Two sets of inputs were added for feedback and setpoint.
SED2 VFD LON Interface Option Operating Instructions Variable Speed Motor Drive Functional Profile 6010 Input Network Variables nv2 Mandatory Network Variables nviDrvSpeedStpt Optional Network Variables nv4 nviDrvSpeedScale Output Network Variables nv3 nvoDrvSpeed nv5 nvoDrvCurnt nv6 nvoDrvVolt nv7 nvoDrvPwr nv8 nvoDrvRunHours nv9 nvoAlarm nv20 nvoHiPress Feedback nv21 nvoLoPress nv11 nviLoPress nv22 nvoTemp nv12 nviTemp nv23 nvoCO2 nv13 nviCO2 Local Information of VFD nv10 nviHiPress nv24
LON Interface Option Overview Network Variables for Object 0 (Node Object) Network Variable Input or Output Units of Measurement Description nviRequest Input Object Request nvoStatus Output Object Status Network Variable Inputs (nvi) for Object 1 Index Network Variable Input (nvi) Units of Measurement Description nv2 nviDrvSpeedStpt On/off switch and speed setpoint Drive speed setpoint; the speed setpoint value is fed into the drive register r2050[1].
SED2 VFD LON Interface Option Operating Instructions Network Variable Outputs (nvo) for Object 1 Index Network Variable Output (nvo) Units of Measurement Description nv3 nvoDrvSpeed Percent (0 to 100%) Feedback drive speed. nv5 nvoDrvCurnt Amp Feedback drive output current. nv6 nvoDrvVolt Volt Feedback drive output voltage. nv7 nvoDrvPwr Power-kilowatt Feedback drive output power. nv8 nvoDrvRunHours time-hours Feedback drive total run hours.
LON Interface Option Overview Standard Configuration Property Type (SCPTs) The following SCPTs are network configuration property inputs (nci). Index and Configuration Mandatory Property (M) or Language-dependent Optional (O) Name Associated Network Variable (nvi, nvo) Units of Measurement Description nc37 nciLocation Location Entire Object Location label; used to provide physical location of the node; not passed to motor drive. nc38 nciNmlFreq nomFreq Entire Object Nominal motor frequency.
SED2 VFD LON Interface Option Operating Instructions Installation and Wiring SED2 VFD Frame Sizes A, B, and C WARNING: Make sure that the SED2 VFD is de-energized (off) before you install or remove the LON Interface Option. 1. Remove the SED2 VFD operator panel. 2. Install LON Interface on the SED2 VFD I/O module (Figure 4) by inserting two bottom guides into appropriate slots at the sides of the I/O module and pushing the upper section inward until the locking mechanism latches. 3.
Installation and Wiring SED2 VFD Frame Sizes D, E, and F WARNING: Make sure that the SED2 VFD is de-energized (off) before you install or remove the LON Interface Option. 6. Terminate end of network cable with a single, two-pin, female LonWorks FTT-10A connector. 7. Attach network cable FTT-10A connector to connector at bottom of Lon Interface (Figure 5 and 7). 8. Reinstall bottom cover, side cover, and the SED2 VFD operator panel.
SED2 VFD LON Interface Option Operating Instructions Installation and Wiring Notes WARNING: A VFD can be switched on unintentionally if the serial bus installation is not operated correctly. The bus must be started by personnel who are qualified and trained in installing systems of this type. 1. DIP Switch Leave DIP switches OFF for proper operation of the LON Interface Option. 2. WIRING Wiring must conform to local codes and ordinances. 3. WIRE ROUTING Maintain a minimum of 5 ft (1.
Startup Procedures Startup Procedures Setting Up SED2 VFD Parameters See SED2 VFD Operation & Maintenance Manual (Document No. 125-3202) for procedures to commission and start up the SED2 VFD. Table 1 lists the SED2 parameter settings that are required for correct communications and control of the SED2 VFD with a LON Interface Option. CAUTION: Changes made to the parameters other than what is listed in Table 1 can result in damaging the drive or building equipment. Table 1.
SED2 VFD LON Interface Option Operating Instructions Verifying Parameter Operations After setting VFD parameters, perform the following steps to verify parameter operations using the drive keypad: Step Press Action Displays r0000. 1 2 and Enables scrolling to the appropriate parameter number. Displays the value of the selected parameter. 3 4 and Enables scrolling to the appropriate parameter value. Confirms parameter value setting and enables scrolling to other parameter numbers.
Application Note using Ni 1000 Sensor Example Application Note using Ni 1000 Sensor Example Use the following parameter settings for PID loop control via the LON Interface Option. Parameter and Setting Value of Parameter Explanation of Value P2201, set to appropriate setting for your installation. Fixed PID setpoint in degrees Celsius. P2253[0], set to one of the following: Selection of setpoint source. LON-mapped setpoint. P0701[0], set to 16. Local drive enable.
SED2 VFD LON Interface Option Operating Instructions Parameter and Setting Value of Parameter r0754[0] for analog input 1 or r0754[1] for analog input 2. Read only; check scaled value. P2280, set to 1.2. P-gain. P2285, set to 30. I-gain. Confirm P0700 = 6. LON communication link. Explanation of Value Confirm P1000 = 6. Press P to exit programming.
Technical Specifications Technical Specifications Specifications Description Processor Type Neuron® 3120® Processor Clock Speed 40 MHz Memory Size 16 KB ROM, 2 KB RAM Network Communication Speed 78 Kbps (FTT-10) Node Identification Fixed, unique Neuron ID, software configurable node ID Status LED Tri-color (green, orange, red) LED provides indication of current operating status Service Pin Provides external activation of service pin message Network Terminator Bus Topology: 105 ohm at both
SED2 VFD LON Interface Option Operating Instructions Troubleshooting WARNING: Make sure that the SED2 VFD is de-energized (off) before you install or remove the LON Interface Option. Status LED Functionality A tri-color LED provides indication of current LON Interface Option operating status and error conditions, such as if more than one SNVT is bound by LONWorks. Table 2 describes the LED indication. Table 2. LON Interface Option Status LED Indication.
Troubleshooting Siemens Building Technologies, Inc.
SED2 VFD LON Interface Option Operating Instructions Siemens Building Technologies, Inc. 1000 Deerfield Parkway Buffalo Grove, IL 60089-4513 Tel: +1 847-215-1000 Fax +1 847-215-1093 Siemens Building Technologies, Ltd. 2 Kenview Blvd. Brampton, Ontario Canada L6T 5E4 Tel: +1 905-799-9937 www.sbt.siemens.
