Installation Instructions

ManualsBrandsSiemens ManualsMonitorSED2

Document No. 129-375

October 2, 2009

SED2 VFD Electronic (E) Bypass Option

EMC Filter Package

Item Number 129-375, Rev. 012 Page 1 of 6

Product Description

The EMC Filter cleans the three-phase power input to

a SED2 VFD E-Bypass Option.

Product Numbers

994-975 EMC filter package for bypass frame

sizes A and B.

994-976 EMC filter package for bypass frame size

994-977 EMC filter package for bypass frame

sizes D and E.

944-978 EMC filter package for bypass frame

size F.

Expected Installation Time

2 hours

Warning/Caution Notations

WARNING:

Personal injury/loss of life may

occur if you do not perform a

procedure as specified.

CAUTION:

Equipment damage may occur if

you do not perform a procedure

as specified.

WARNING:

• This equipment generates, uses and

radiates radio frequency energy. If not

installed and used in accordance with

the instructions manual, may cause

interference to radio communications.

• Operation of this equipment in a

residential area may cause

interference. At their own expense,

users will be required to take whatever

measures to correct the interference.

• Main short circuit protection and

disconnect by others. Branch circuit

protection to be provided by installer

per UL508A, if not provided with drive.

NOTE: E-Bypass with EMC Filter package has been

tested and found to comply with the limits for

a Class A digital device, pursuant to Part 15

of the FCC rules. These limits are designed

to provide reasonable protection against such

interference when operated in a commercial

environment.

Prerequisites

E-Bypass Option must be previously installed.

Installation

Filter Installation

See Figures 1 through 6 throughout this procedure.

CAUTIONS:

• Make certain 3-phase line power supply is

OFF or disconnected.

• Make certain disconnect switch or circuit

breaker in Bypass Option cabinet is OFF.

1. Locate and punch hole for conduit in Bypass

Option cabinet.

CAUTION:

Make certain metal filings do not fall into

Bypass Option cabinet.

2. Connect fitting and conduit to Bypass Option

cabinet.

3. Remove EMC filter enclosure cover and install

conduit fitting.

4. Align conduit from Bypass Option into fitting on

EMC filter enclosure and mount EMC filter

enclosure on wall. Secure conduit in place.

Summary of content (6 pages)

PAGE 1
Installation Instructions Document No. 129-375 October 2, 2009 SED2 VFD Electronic (E) Bypass Option EMC Filter Package Product Description The EMC Filter cleans the three-phase power input to a SED2 VFD E-Bypass Option. Product Numbers 994-975 EMC filter package for bypass frame sizes A and B. EMC filter package for bypass frame size C. EMC filter package for bypass frame sizes D and E. EMC filter package for bypass frame size F.
PAGE 2
Document No. 129-375 Installation Instructions October 2, 2009 Wiring Ferrite Bead Installation See Figure 11 throughout this procedure. CAUTIONS: • Make certain 3-phase line power supply is OFF or disconnected. • Make certain disconnect switch or circuit breaker in Bypass Option cabinet is OFF. 1. Route wiring between Bypass Option cabinet and filter enclosure through conduit. 2. Connect wiring to disconnect switch or circuit breaker in Bypass Option cabinet. 3.
PAGE 3
Document No. 129-375 Installation Instructions October 2, 2009 NOTE: External mounting hardware provided by others. Figure 2. Filter Dimensions for Bypass Frame Sizes A, B, and C. Dimensions in Inches (Millimeters). NOTE: Mounting hardware provided by others. Figure 3. Filter Dimensions for Bypass Frame Sizes D, E, and F. Dimensions in Inches (Millimeters). Siemens Industry, Inc. http://www.sbt.siemens.
PAGE 4
Document No. 129-375 Installation Instructions October 2, 2009 NOTE: Conduit, fittings, and wire provided by others. Figure 4. Conduit Location on Side of Bypass Option. (Bypass Frame Sizes A through E shown). Figure 5. Typical EMC Filter Mounting for Bypass Frame Sizes A, B, and C NOTE: Conduit, fittings, and wire provided by others. Figure 6. Typical EMC Filter Mounting for Bypass Frame Sizes D and E. Figure 7. Typical EMC Filter Mounting for Bypass Frame Size F. Page 4 of 6 http://www.sbt.
PAGE 5
Document No. 129-375 Installation Instructions October 2, 2009 Figure 8. Routing of Power and Control Wiring for Bypass Frame Sizes A and B. Figure 9. Routing of Power and Control Wiring for Bypass Frame Sizes C, D, and E. Figure 10. Routing of Power and Control Wiring for Bypass Frame Size F. Siemens Industry, Inc. http://www.sbt.siemens.
PAGE 6
Document No. 129-375 Installation Instructions October 2, 2009 CAUTION: Only personnel certified to work with high voltage 3-phase line power are to complete wiring. Figure 11. EMC Filter Terminal Connections. Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as design improvements are introduced. Other product or company names mentioned herein may be the trademarks of their respective owners.