Installation Instructions

ManualsBrandsSiemens ManualsMonitorSED2

Document No. 129-393

October 2, 2009

Control Board Upgrade for SED2 VFD

(Version 1.17, 1.20, and 1.30 to Version 1.4x)

Item Number 129-393, Rev. DA Page 1 of 15

Description

These installation instructions describe how to

exchange a Version 1.17, 1.20, and 1.30 Control

Board (V1.17, V1.20, and V1.30) of a SED2 Variable

Frequency Drive (VFD) with a Version 1.4x Control

Board (V1.4x).

Product Numbers

SED2-CBV140, includes control board with Version

1.4x firmware already installed.

Warning/Caution Notations

WARNING:

Personal injury/loss of life may

occur if you do not follow a

procedure as specified.

CAUTION:

Equipment damage, or loss of

data may occur if you do not

follow a procedure as specified.

Required Tools

• Small flat-blade screwdriver

• Torx T20 driver

• Small needle-nose pliers

• Basic Operator Panel (BOP)/Advanced

Operator Panel (AOP)

Expected Installation Time

25 minutes

Record Parameter Settings

If parameter settings are not recorded, drive will

need to be completely re-commissioned and start-up

procedures performed.

Manually Record Parameter Set

Record drive specific parameter settings from

BOP/AOP in the Parameter List section at the end of

this document.

NOTE: For drives with bypass, settings of P0748

and P0704 must be recorded.

Upload (Upread) Parameter Set

Use an AOP to upload a parameter set from a SED2

and store that parameter set in the internal memory

of the AOP. See the SED2 VFD Advanced Operator

Panel (AOP) Operating Instructions, Document

Number 125-3206 for more details on AOP

operation.

1. From the main menu, use

and to scroll

through the list of options and to highlight the

Upread item.

Press

to confirm the selection. Press to

cancel the upload process.

The AOP displays an upload/upread menu.

2. Use

and to scroll through the list of

parameter sets and to highlight the parameter

set into which information will be written.

Press

to confirm the selection.

NOTES:

• If the selected parameter set already

contains information, the AOP prompts to

clear the existing parameter set.

• Simultaneously press

and when

uploading to delete the existing parameter

set.

3. The AOP prompts for confirmation.

Press

to confirm the process. Press to

cancel the upload process.

The AOP displays a wait screen while the

upload process occurs.

4. On completion of the upload process, the AOP

returns to the main menu.

Summary of content (15 pages)

PAGE 1
Installation Instructions Document No. 129-393 October 2, 2009 Control Board Upgrade for SED2 VFD (Version 1.17, 1.20, and 1.30 to Version 1.4x) Upload (Upread) Parameter Set Description These installation instructions describe how to exchange a Version 1.17, 1.20, and 1.30 Control Board (V1.17, V1.20, and V1.30) of a SED2 Variable Frequency Drive (VFD) with a Version 1.4x Control Board (V1.4x). Product Numbers SED2-CBV140, includes control board with Version 1.4x firmware already installed.
PAGE 2
Document No. 129-393 Installation Instructions October 2, 2009 Installation for SED2 Frame Size A, B, and C 3. Detach I/O module (Figure 3). Allow I/O module to rest beneath SED2 (Figure 4). CAUTION: Do not use this upgrade if your control board is Version 1.15 (V1.15). If upgrading a V1.15 Control Board, contact your field support for assistance. 1. If on a network, read and record the address of parameter P0918 here: WARNING: Make certain SED2 supply power is disconnected. Figure 3.
PAGE 3
Document No. 129-393 Installation Instructions October 2, 2009 4. Remove operator panel release button by using a needle nose pliers to slide out wire spring from retaining slots (Figure 5). Save wire spring and release button for reassembly. 5. Remove control module cover (Figures 6 and 7). Set aside control module cover for reassembly. CAUTION: Be careful that wire spring does not spring out and cause injury. Figure 6. Loosening Control Module Cover Bottom Clip. Figure 5.
PAGE 4
Document No. 129-393 Installation Instructions October 2, 2009 6. Remove control board grounding screw using a Torx T20 driver (Figure 8). Save screw for reassembly. CAUTION: Before installing new Control Board, discharge any static electricity by contacting earth ground (such as by touching the SED2 housing). 8. Mount new Control Board (Figure 10). CAUTION: Make certain control board connection pins align correctly with SED2 connector openings to avoid equipment damage. Figure 8.
PAGE 5
Document No. 129-393 Installation Instructions October 2, 2009 9. Reinstall control board grounding screw using a Torx T20 driver (Figure 11). The grounding screw also aids positioning and prevents rotation of the control board. 11. Set Motor Frequency and Unit of Measurement DIP switches (Figure 13) as follows: DIP Switch Position 1 OFF 2 ON Function Not for customer use. NOTE: This switch must remain OFF for proper operation. North American operation (60 Hz, hp). Figure 11.
PAGE 6
Document No. 129-393 Installation Instructions October 2, 2009 13. Reattach I/O module (Figure 15). Installation for SED2 Frame Size D, E, and F CAUTION: Do not use this upgrade if your control board is Version 1.15 (V1.15). If upgrading a V1.15 Control Board, contact your field support for assistance. 1. If on a network, read and record the address of parameter P0918 here: Figure 15. Reattaching I/O Module. 14. Reinstall terminal cover, operator panel, and cover (Frame Sizes B and C).
PAGE 7
Document No. 129-393 Installation Instructions October 2, 2009 4. Detach I/O module (Figure 21). Allow I/O module to rest beneath SED2 (Figure 22). Figure 21. Detaching I/O Module. Figure 19. Removing Terminal Cover. 3. Detach the operator panel extension module (Figure 20). Do not disconnect ribbon cable. Insert extension module where operator panel was located. Figure 22. Resting I/O Module Beneath SED2. Figure 20. Removing Operator Panel Extension Module. Siemens Industry, Inc.
PAGE 8
Document No. 129-393 Installation Instructions October 2, 2009 5. Detach operator panel release button by using a needle nose pliers to slide out wire spring from retaining slots (Figure 23). Save wire spring and release button for reassembly. 7. Remove control board grounding screw using a Torx T20 driver (Figure 25). Save screw for reassembly. CAUTION: Be careful that wire spring does not spring out and cause injury. Figure 25. Removing Control Board Grounding Screw. Figure 23.
PAGE 9
Document No. 129-393 Installation Instructions October 2, 2009 CAUTION: Before installing new Control Board, discharge any static electricity by contacting earth ground (such as by touching the SED2 housing). 9. 10. Reinstall control board grounding screw using a Torx T20 driver (Figure 28). The grounding screw also aids positioning and prevents rotation of the control board. Mount new Control Board (Figure 27).
PAGE 10
Document No. 129-393 Installation Instructions October 2, 2009 12. Set Motor Frequency and Unit of Measurement DIP switches (Figure 30) as follows: DIP Switch Position 1 OFF 2 ON 14. Reattach I/O Module (Figure 32). Function Not for customer use. NOTE: This switch must remain OFF for proper operation. North American operation (60 Hz, hp). Figure 32. Reattaching I/O Module. 15. Reattach the operator panel extension module (Figure 33). Figure 30. Setting Control Board DIP Switches. 13.
PAGE 11
Document No. 129-393 Installation Instructions October 2, 2009 16. Reinstall terminal cover and operator panel (Figures 34 and 35). Figure 35. Reinstalling Operator Panel. Figure 34. Reinstalling Terminal Cover. Siemens Industry, Inc. 17. Update drive label "issue" field on outside of drive from "V1.17", "V1.20", or “V1.30” to “V1.4x”. This completes installation. Continue with the Startup section.
PAGE 12
Document No. 129-393 Installation Instructions October 2, 2009 Startup Download Parameter Set 1. 2. Use an AOP to download the stored parameter set to the SED2. See the SED2 VFD Advanced Operator Panel (AOP) Operating Instructions, Document Number 125-3206 for more details on AOP operation. 3. 4. 5. Reapply SED2 supply power. Set P0010=30 (commissioning parameter filter, factory setting) and P0970=1 (factory reset, parameter reset).
PAGE 13
Document No. 129-393 Installation Instructions October 2, 2009 Parameter Parameter List NOTE: Certain parameters have more than one index requiring setting.
PAGE 14
Document No.
PAGE 15
Document No.