Technical data

ManualsBrandsSiemens ManualsMonitorSED2

SED2 Operation and Maintenance Manual

102 Siemens Building Technologies, Inc

r0054 CO/BO: Act. control word 1

Min: - Def: - Max: -

Level 3

Bit Fields:

Bit00 ON/OFF1 0 NO, 1 YES

Bit01 OFF2: Electrical stop 0 YES, 1 NO

Bit02 OFF3: Fast stop 0 YES, 1 NO

Bit03 Pulse enable 0 NO, 1 YES

Bit04 RFG enable 0 NO, 1 YES

Bit05 RFG start 0 NO, 1 YES

Bit06 Setpoint enable 0 NO, 1 YES

Bit07 Fault acknowledge 0 NO, 1 YES

Bit08 JOG right 0 NO, 1 YES

Bit09 JOG left 0 NO, 1 YES

Bit10 Control from PLC 0 NO, 1 YES

Bit11 Reverse (setpoint inversion) 0 NO, 1 YES

Bit13 Motor potentiometer MOP up 0 NO, 1 YES

Bit14 Motor potentiometer MOP down 0 NO, 1 YES

Bit15 CDS Bit 0 (Local/Remote) 0 NO, 1 YES

Details:

See description of seven segment display.

r0055 CO/BO: Add. act. control word

Min: - Def: - Max: -

Level 3

Bit Fields:

Bit00 Fixed frequency Bit 0 0 NO, 1 YES

Bit01 Fixed frequency Bit 1 0 NO, 1 YES

Bit02 Fixed frequency Bit 2 0 NO, 1 YES

Bit03 Fixed frequency Bit 3 0 NO, 1 YES

Bit08 PID enabled 0 NO, 1 YES

Bit09 DC brake enabled 0 NO, 1 YES

Bit11 Droop 0 NO, 1 YES

Bit12 Torque control 0 NO, 1 YES

Bit13 External fault 1 0 YES, 0 NO

Details:

See description of seven segment display.

r0056 CO/BO: Status of motor control

Min: - Def: - Max: -

Level 3

Bit Fields:

Bit00 Init. control finished 0 NO, 1 YES

Bit01 Motor demagnetizing finished 0 NO, 1 YES

Bit02 Pulses enabled 0 NO, 1 YES

Bit03 Voltage soft start select 0 NO, 1 YES

Bit04 Motor excitation finished 0 NO, 1 YES

Bit05 Starting boost active 0 NO, 1 YES

Bit06 Acceleration boost active 0 NO, 1 YES

Bit07 Frequency is negative 0 NO, 1 YES

Bit08 Field weakening active 0 NO, 1 YES

Bit09 Volts setpoint limited 0 NO, 1 YES

Bit10 Slip frequency limited 0 NO, 1 YES

Bit11 F_out > F_max Freq. limited 0 NO, 1 YES

Bit12 Phase reversal selected 0 NO, 1 YES

Bit13 I-max controller active 0 NO, 1 YES

Bit14 Vdc-max controller active 0 NO, 1 YES

Bit15 Vdc-min controller active 0 NO, 1 YES

Details:

See description of seven segment display.

r0061 CO: Act. rotor speed

Min: - Def: - Max: -

Level 3

r0086 CO: Act. active current

Min: - Def: - Max: -

Level 3

Dependency:

Applies when V/f control is selected in P1300 (control mode); otherwise, the display shows the value zero.