User Manual

ManualsBrandsSiemens ManualsFire - Addressable Stand-alone PanelsXC10 compact panels combine fi re detection and extinguishing control – for comprehensive safety.

Operation (short) MP 2.1

FC20xx Fire control panel

FT2040 Fire terminal

ALARM-Procedure Page 1

Switching off detector zones / detectors Page 2

Switching on detector zones / detectors Page 4

Procedure in case of Fault Page 4

Document ID: 009906_d_en_GB

Edition: 05.2009

1 of 4

ALARM Procedure

with Alarm Verification Concept (AVC), suggested possible procedure, subject to local requirements

Action / Condition Consequence / Status

Press <Acknowledge> on the PMI before allowed

response time (t1) runs out (Password required)

Buzzer is turned off, alarm is acknowledged.

Countdown t2 for the investigation of the cause of alarm starts.

Read top line on display:

"Fire brigade in" "mm:ss"

Remaining time is shown as countdown before building

evacuation and Fire Brigade call.

Read fire location on display.

Go to the fire location.

Information on the cause of ALARM,

damage limitation.

Decide: MAJOR INCIDENT or minor incident.

If required, initiation of suitable emergency measures.

MAJOR INCIDENT:

Press <Alarm delay off>

or actuate nearest manual call point.

Read top line on display:

● "Remote transmission activated"

● "Fire brigade called !"

● "Call fire brigade !"

Remote transmission switched off / not available or

defective.

The remote transmission for fire alarm is activated

immediately.

● Transmission to fire brigade not confirmed yet.

● ALARM transmitted to fire brigade.

● Fire brigade must be called by phone!

No automatic transmission to fire brigade.

Dial the following no.:

Minor incident:

Press <Reset>.

(Password required)

Fire detection system is in normal condition unless another event

occurs.

It may be necessary to vent the room before resetting is possible.

Elements that cannot be reset can be switched off temporarily.

During the alarm, optionally press

<Sounders Evacuate> on the PMI.

(Password required)

Deactivates the acoustic alarm devices during the alarm.

(Reactivation is possible by pressing the button again)

1 2 3

4 5 6

7 8 9

0 #

ALARM

FAUL

ISOLATION

DETECTOR TES

System

Fault

Scroll alarms

Remote alarm

Active

Fault / Off

Sounders

Fault / Off

Active Evacuate

Silence buzzer

Acknowledge

Reset

Alarm delay off

Premises manned

Fire brigade in

001 ALARM

Autom. FIRE ALARM Zone no.2

Execute

Commands

Options

Fx20x

Control function

Fault / Of

Active

Go to fire location

Decide

00:02:51

Switch to

Standard view

Main Building

Ground Floor

1/01 Meeting Room 001

00:02:51

Summary of content (8 pages)

PAGE 1
ALARM-Procedure Switching off detector zones / detectors Switching on detector zones / detectors Procedure in case of Fault Operation (short) MP 2.1 FC20xx Fire control panel FT2040 Fire terminal Page 1 Page 2 Page 4 Page 4 ALARM Procedure with Alarm Verification Concept (AVC), suggested possible procedure, subject to local requirements Fx20xx ALARM Fire brigade in 001 ALARM 2. Autom. FIRE ALARM Main Building Ground Floor 1/01 Meeting Room Execute Commands 00:02:51 Zone no.2 00:02:51 3.
PAGE 2
Switching off detector zones / detectors The following example represents a possible operation sequence: DANGER System parts that have been switched off make it impossible to detect fires or faults! ⇒ Fire may spread unhindered. ⇒ The area that has been switched off must be manually supervised. ⇒ System parts that have been switched off must be switched back on as soon as possible. Switching off a detector zone (password required) Step 1. 2. Press the button to open the main menu.
PAGE 3
Switching off a detector (Password required) Step 1. Press the button to open the main menu. (Password required) Result ⇒ Main menu Exit with Message summary Functions Favorites Topology Function On/Off 2. Press <4> to open the menu item "Topology". ⇒ Note: The numbers in brackets (1)… can be entered with the numeric keys <1>… below the main menu button. 3. Press <1> "Detection tree". Function On/Off ⇒ Press Softkey <2> "Lower level". 7.
PAGE 4
Switching on detector zones / detectors (Password required) ⇒ When there is no event with a higher priority, isolations (switched off) are directly indicated on the display. You may then directly proceed with Step 3 below. ⇒ When all zones within a section (a zone is a detector in this system’s terminology) are turned off, the section is additionally indicated as switched off. ⇒ Detectors that still contain smoke or test gas cannot be switched back on. Step 1. Press the button to open the main menu.
PAGE 5
ALARM-Procedure Switching off detector zones / detectors Switching on detector zones / detectors Procedure in case of Fault Operation (short) MP 2.1 FC20xx Fire control panel FT2040 Fire terminal Page 1 Page 2 Page 4 Page 4 ALARM Procedure no Alarm Verification Concept (AVC), suggested possible procedure, subject to local requirements Fx20xx ALARM 2. Call Fire Brigade! 001 ALARM Autom. FIRE ALARM Main Building Ground Floor 1/01 Meeting Room Execute Commands Zone no.2 3.
PAGE 6
Switching off detector zones / detectors The following example represents a possible operation sequence: DANGER System parts that have been switched off make it impossible to detect fires or faults! ⇒ Fire may spread unhindered. ⇒ The area that has been switched off must be manually supervised. ⇒ System parts that have been switched off must be switched back on as soon as possible. Switching off a detector zone (password required) Step 1. 2. Press the button to open the main menu.
PAGE 7
Switching off a detector (Password required) Step 1. Press the button to open the main menu. (Password required) Result ⇒ Main menu Exit with Message summary Functions Favorites Topology Function On/Off 2. Press <4> to open the menu item "Topology". ⇒ Note: The numbers in brackets (1)… can be entered with the numeric keys <1>… below the main menu button. 3. Press <1> "Detection tree". Function On/Off ⇒ Press Softkey <2> "Lower level". 7.
PAGE 8
Switching on detector zones / detectors (Password required) ⇒ When there is no event with a higher priority, isolations (switched off) are directly indicated on the display. You may then directly proceed with Step 3 below. ⇒ When all zones (a zone is a detector in this system’s terminology) are turned off, the section is additionally indicated as switched off. ⇒ Detectors that still contain smoke or test gas cannot be switched back on. Step 1. Press the button to open the main menu.