Installation Instructions

PN P85583-001A
Figure 2: Wire Connection
Figure 1: Speaker / Strobe Wiring
Install signaling appliance to backbox using mounting screws provided.
NOTE: Check electrical ratings specied in Tables 1 and 2 (as appropriate) to ensure proper electrical input. Ensure the speaker wiring is con-
nected to speaker terminals only, and strobe wiring is connected to strobe terminals only. Ensure the wiring at the FACP is correct.
NOTE: Wiring method shall be in accordance with CSA C22.1, Canadian Electrical Code, Part 1, Safety Standard for Electrical Installations,
Section 32.
WARNING: Improper electrical input can damage the product or cause it to malfunction.
NOTE: The speaker strobe appliances must be set to the desired dBA sound output level before they are installed. This is done by properly
setting the slide switch in accordance with these instructions.
WARNING: Incorrect settings will result in improper performance. Factory setting is F: 70V @ 1/2 W.
NOTE: Slide the Switch Indicator selection switch to the desired tap setting.
NOTE: The SLSPSW comes pre-set at 15cd.
Table 5: Speaker Voltage and Wattage Connection
Chart
Position 25V 70V
A 2 ------
B 1 ------
C 1/2 ------
D 1/4 2
E 1/8 1
F ------ 1/2
G ------ 1/4
H ------ 1/8
Figure 4: Strobe Candela indicator
Figure 3: Speaker Selector Switch Setting
Located on Rear of Device
Figure 5: SLSPW and SLSPSW-A Expected Light Output
CAUTION: Always operate audio ampliers and speakers within their specied ratings. Excessive input may distort sound quality and may
damage audio equipment. Improper input voltage can damage speaker. If distortion is heard, check for clipping of the audio appliance with an
oscilloscope and reduce the amplier input level or gain level to eliminate any clipping.
Figure 6: Surface Backbox Mounting Figure 7: Four-Inch Square Backbox Mounting
MOUNTING OPTIONS
Although the limits shown for each mounting option comply with the National Electrical Code (NEC), Siemens recommends use of the largest
backbox option shown and the use of approved stranded eld wires, whenever possible, to provide additional wiring room for easy installation
and minimum stress on the product from wiring.
NOTE: Speaker-strobe mounting depicted in Figure 6 & 7. For non-strobe speaker surface mounting, use same surface box as depicted in
Figure 6.
NOTE: Surface backbox (LFSBB) shown in Figure 6, is compatible with wiremold and conduit. Mounting holes are for single-gang, double-
gang, and #10 wood screws for stud mounting. If metal conduit is installed onto top and bottom conduit entrances, then an insulated grounding
wire (18 AWG, supplied) must be connected between the top and bottom plate by using thread cutting screws (supplied) to provide electrical
continuity per UL 50.
MOUNTING PROCEDURES
NOTE: Remove the Lens Protector Tape and cardboard speaker protector before replacing the appliance Cover Grill.
CAUTION: Check that the installed product will have su󰀩cient clearance and wiring room prior to installing backboxes and conduit, especially if
sheathed multiconductor cable or 3/4” conduit ttings are used.
CAUTION: The candela select switch must be eld set to the required candela intensity before installation. When changing the setting of the
candela select switch make certain that it clicks in place. After changing the candela setting the appliance must be retested to verify proper
operation. Improper setting of the candela select switch may result in operation at the wrong candela
0%
20%
40%
60%
80%
100%
120%
140%
160%
180%
200%
-100 -80 -60 -40 -20 0 20 40 60 80 100
% of Rating
Angle
Expected
Horizontal
Values
Expected
Vertical
Values