9000 405 550 (8906) de Gebrauchsanleitung S
A B C 7 8 9 Reset 3 sec.
de Inhaltsverzeichnis Sicherheitshinweise . . . . . . . . . . . . . . . . 4 Bei der Anlieferung . . . . . . . . . . . . . . . 4 Bei der Installation . . . . . . . . . . . . . . . 4 Im täglichen Betrieb . . . . . . . . . . . . . . 4 Bei Kindern im Haushalt . . . . . . . . . . . 4 Türverriegelung . . . . . . . . . . . . . . . . . . 4 Tastensperre . . . . . . . . . . . . . . . . . . . . 5 Bei auftretenden Schäden . . . . . . . . . . 5 Bei der Entsorgung . . . . . . . . . . . . . . . 5 Gerät kennen lernen . .
de Sicherheitshinweise Bei der Anlieferung – Überprüfen Sie Verpackung und Geschirrspüler sofort auf Transportschäden. Nehmen Sie ein beschädigtes Gerät nicht in Betrieb, sondern halten Sie Rücksprache mit Ihrem Lieferanten. – Entsorgen Sie das Verpackungsmaterial bitte ordnungsgemäß. – Verpackung und Ihre Teile nicht spielenden Kindern überlassen. Es besteht Erstickungsgefahr durch Faltkartons und Folien.
de Kindersicherung (Tastensperre) Sie können Ihr Gerät gegen unbeabsichtigtes Programm abbrechen (z.B. Fehlbedienung durch Kinder) sichern. Tastensperre aktivieren: – Gewünschtes Programm starten. – Taste + ca. 4 sec. gedrückt halten, bis ’– in der Ziffernanzeige erscheint. Wird während des Programmablaufes eine beliebige Taste betätigt, erscheint ’– in der Ziffernanzeige. Ein Abbrechen des Programms (Reset) ist nicht möglich. Tastensperre deaktivieren: – Taste + ca.4 sec.
de Enthärtungsanlage Für gute Spülergebnisse benötigt der Geschirrspüler weiches, d.h. kalkarmes Wasser, sonst lagern sich weiße Kalkrückstände auf Geschirr und Innenbehälter ab. Leitungswasser oberhalb von 7° dH (1,2 mmol/l) muss enthärtet werden. Dies geschieht mit Hilfe von Spezialsalz (Regeneriersalz) in der Enthärtungsanlage des Geschirrspülers. Die Einstellung und damit die benötigte Salzmenge ist abhängig vom Härtegrad Ihres Leitungswassers (siehe Tabelle).
de Salznachfüllanzeige / Enthärtung ausschalten Spezialsalz Verwendung von Spezialsalz Das Salznachfüllen muss immer unmittelbar vor dem Einschalten des Gerätes erfolgen. So wird erreicht, dass übergelaufene Salzlösung sofort ausgespült wird und keine Korrosion am Spülbehälter auftreten kann. – Öffnen Sie den Schraubverschluss des Vorratsbehälters 1J. – Füllen Sie den Behälter mit Wasser (nur bei der ersten Inbetriebnahme nötig). – Füllen Sie dann Spezialsalz (kein Speisesalz oder Tabletten) ein.
de Klarspüler Sobald die Klarspülernachfüllanzeige h in der Blende leuchtet, ist noch eine Klarspülreserve von 1 - 2 Spülvorgängen vorhanden. Klarspüler sollte nachgefüllt werden. Der Klarspüler wird für fleckenloses Geschirr und klare Gläser benötigt. Verwenden Sie nur Klarspüler für Haushaltsgeschirrspüler. Kombinierte Reiniger mit Klarspülerkomponente können nur bis zu einer Wasserhärte von 21° dH (37° fH, 26° Clarke, 3,7 mmol/l) verwendet werden.
de Geschirr Nicht geeignet – Besteck- und Geschirrteile aus Holz. – Empfindliche Dekorgläser, kunstgewerbliches und antikes Geschirr. Diese Dekore sind nicht spülmaschinenfest. – Nicht hitzebeständige Kunststoffteile. – Kupfer- und Zinngeschirr. – Geschirrteile, die mit Asche, Wachs, Schmierfett oder Farbe verunreinigt sind. Aufglasdekore, Aluminium- und Silberteile können beim Spülen zum Verfärben und Verblassen neigen. Auch einige Glassorten (wie z. B.
de Töpfe Besteckschublade Unterer Geschirrkorb 1Z Ordnen Sie das Besteck wie abgebildet in die Besteckschublade 1" ein. Getrenntes Einordnen erleichtert nach dem Spülen das Entnehmen. Die Schublade kann herausgenommen werden. Tipp Stark verschmutztes Geschirr (Töpfe) sollten Sie im Unterkorb einräumen. Aufgrund des stärkeren Sprühstrahls erhalten Sie so ein besseres Spülergebnis.
de Tassenauflagebügel * Korbhöhe verstellen * je nach Modell Beim Spülen von Tassen kann der Tassenauflagebügel hochgeklappt werden. Die zusätzliche Schräglage vermindert das Ansammeln von Wasser auf der Tassenunterseite. Bei hohen Gläsern empfiehlt es sich, den Tassenauflagebügel umgeklappt zu lassen. Der obere Geschirrkorb 1* kann in der Höhe in 3 Stufen verstellt werden, um entweder im Ober- oder Unterkorb mehr Platz zu schaffen. Gerätehöhe 81,5 cm Stufe 1 max. ø Stufe 2 max. ø Stufe 3 max.
de Reiniger Sie können Tabs sowie pulverförmige oder flüssige Reiniger für Geschirrspüler verwenden, keinesfalls aber Handspülmittel. Je nach Verschmutzung kann mit Pulver oder einem flüssigen Reiniger die Dosierung individuell angepasst werden. Tabs enthalten für alle Reinigungsaufgaben eine ausreichend große Menge an Wirkstoffen. Moderne, leistungsfähige Reiniger verwenden überwiegend eine niederalkalische Rezeptur mit Phosphat und Enzymen. Phosphate binden den Kalk im Wasser.
de Tipp Bei wenig verschmutztem Geschirr genügt üblicherweise eine etwas geringere als die angegebene Reinigermenge. Geeignete Reinigungs- und Pflegemittel können online über unsere Internetseite oder über den Kundendienst bezogen werden (siehe Rückseite). Kombireiniger Neben herkömmlichen Reinigern (Solo) werden eine Reihe von Produkten mit zusätzlichen Funktionen angeboten.
de Programmübersicht In dieser Übersicht ist die max. mögliche Programmanzahl dargestellt. Die entsprechenden Programme und ihre Anordnung entnehmen Sie bitte Ihrer Bedienblende.
de Zusatzfunktionen * je nach Modell Über die Tasten Zusatzfunktionen H einstellbar. Ÿ Zeit sparen (VarioSpeed) * Mit der Funktion >>Zeit sparen<< kann die Laufzeit je nach gewähltem Spülprogramm um ca. 20% bis 50% verkürzt werden. Die jeweilige Laufzeitveränderung wird in der Ziffernanzeige )" dargestellt. Um bei verkürzter Laufzeit optimale Reinigungsergebnisse zu erzielen, werden Wasser- und Energieverbrauch erhöht. § Halbe Beladung * Wenn Sie nur wenig Geschirr zu spülen haben (z. B.
de Zeitvorwahl * Programm unterbrechen * je nach Modell Sie können den Programmstart in Stundenschritten bis zu 24 Stunden verschieben. – Tür schließen. – EIN-/AUS-Schalter ( einschalten. – Taste @ + drücken, bis die Ziffernanzeige )" auf œ:‹‚ springt. – Taste @ + oder – so oft drücken, bis die angezeigte Zeit Ihren Wünschen entspricht. – START-Taste P drücken, die Zeitvorwahl ist aktiviert. – Zum Löschen der Zeitvorwahl die Taste @ + oder – so oft drücken, bis in der Ziffernanzeige )" œ:‹‹ erscheint.
de Intensivtrocknung Im Klarspülen wird mit einer höheren Temperatur gearbeitet und damit ein verbessertes Trocknungsergebnis erreicht. Die Laufzeit kann sich dabei geringfügig erhöhen. (Vorsicht bei empfindlichen Geschirrteilen!) – Tür schließen. – EIN-/AUS-Schalter ( einschalten. – Programmtaste # gedrückt halten und START-Taste P so lange drücken, bis die Ziffernanzeige )" •:‹... anzeigt. – Beide Tasten loslassen.
de Siebe Sprüharme Die Siebe 1R halten grobe Verunreinigungen im Spülwasser von der Pumpe fern. Diese Verunreinigungen können die Siebe gelegentlich verstopfen. Das Siebsystem besteht aus einem Grobsieb, einem flachen Feinsieb und einem Microsieb. – Nach jedem Spülen die Siebe auf Rückstände kontrollieren. – Siebzylinder wie abgebildet losdrehen und Siebsystem herausnehmen. Kalk und Verunreinigungen aus dem Spülwasser können Düsen und Lagerungen der Sprüharme 12 und 1B blockieren.
de Abwasserpumpe Grobe Speisereste aus dem Spülwasser, die von den Sieben nicht zurückgehalten wurden, können die Abwasserpumpe blockieren. Das Spülwasser wird dann nicht abgepumpt und steht über dem Sieb. In diesem Fall: – Trennen Sie grundsätzlich das Gerät zuerst vom Stromnetz. – Siebe 1R ausbauen. – Wasser ausschöpfen, evtl. Schwamm zu Hilfe nehmen.
de ... am Gerät Unterer Sprüharm dreht sich schwer. – Sprüharm blockiert. Tür lässt sich nur schwer öffnen. * – Kindersicherung ist aktiviert. Die Anleitung zur Deaktivierung befindet sich hinten im Umschlag. * Je nach Modell Tür lässt sich nicht schließen. – Türschloss ist umgesprungen. Zur Rücksetzung ist die Tür mit erhöhter Kraft zu schließen. Deckel der Reinigerkammer lässt sich nicht schließen. – Reinigerkammer überfüllt oder Mechanismus durch verklebte Reinigerreste blockiert.
de Schlagendes / Klapperndes Geräusch beim Spülen – Sprüharm schlägt an Geschirrteile. – Geschirrteile nicht richtig eingeordnet. ... am Geschirr Speisereste am Geschirr. – Geschirr zu eng eingeordnet, Geschirrkorb überfüllt. – Zu wenig Reiniger. – Zu schwaches Spülprogramm. – Sprüharmdrehung behindert. – Sprüharmdüsen verstopft. – Siebe verstopft. – Siebe falsch eingesetzt. – Abwasserpumpe blockiert. – Oberkorb rechts und links nicht auf gleiche Höhe eingestellt.
de Kundendienst Sollte es Ihnen nicht gelingen, die Störung zu beheben, wenden Sie sich bitte an Ihren Kundendienst. Die Kontaktdaten für den nächstgelegenen Kundendienst finden Sie auf der Rückseite dieser Gebrauchsanleitung oder im beiliegenden Kundendienst-Verzeichnis. Geben Sie beim Anruf bitte die Gerätenummer (ENr. = 1) und das Fertigungsdatum (FD = 2) an, die Sie auf dem Typenschild 9* an der Gerätetür finden.
de – Installieren Sie das Gerät nicht in der Nähe von Wärmequellen (Heizkörper, Wärmespeicher, Öfen oder anderen Geräten, die Wärme erzeugen) und bauen Sie es nicht unter ein Kochfeld ein. – Nach dem Aufstellen des Gerätes muss der Stecker frei zugänglich sein. – Bei einigen Modellen: Das Kunststoffgehäuse am Wasseranschluss enthält ein elektrisches Ventil, im Zulaufschlauch befinden sich die Anschlussleitungen. Schneiden Sie diesen Schlauch nicht durch, tauchen Sie das Kunststoffgehäuse nicht in Wasser.
de Abwasseranschluss Elektrischer Anschluss – Die erforderlichen Arbeitsschritte aus der Montageanweisung entnehmen, gegebenenfalls Siphon mit Ablaufstutzen montieren. – Abwasserschlauch mit Hilfe der beiliegenden Teile an den Ablaufstutzen des Siphons anschließen.
de Transport Geschirrspüler entleeren und lose Teile sichern. Das Gerät muss durch folgende Schritte entleert werden: – Wasserhahn öffnen. – Tür schließen. – EIN-/AUS-Schalter ( einschalten. Die Anzeigen des zuletzt gewählten Programmes leuchten auf. – Programm mit der höchsten Temperatur wählen. In der Ziffernanzeige )" erscheint die voraussichtliche Programmdauer. – Start-Taste P drücken. Programmablauf startet. – Nach ca. 4 Minuten START-Taste P so lange drücken, bis die Ziffernanzeige ‹:‹‚ anzeigt.
Kindersicherung (Türverriegelung) * 40 Kindersicherung aktivieren. 41 Tür öffnen mit aktivierter Kindersicherung. 42 Kindersicherung deaktivieren. Schließen Sie die Gerätetür immer komplett, wenn Sie das Gerät verlassen. Nur so können Sie Ihre Kinder vor möglichen Gefahren schützen. Backblechsprühkopf * Große Bleche oder Gitter sowie Teller mit einem Durchmesser mehr als 30 cm (Gourmetteller, Pastateller, Platzteller) können Sie mit Hilfe dieses Sprühkopfes reinigen.
AQUA-STOP-Garantie de (entfällt bei Geräten ohne Aqua-Stop) Zusätzlich zu Gewährleistungsansprüchen gegen den Verkäufer aus dem Kaufvertrag und zusätzlich zu unserer Gerätegarantie leisten wir Ersatz zu folgenden Bedingungen: 1. Sollte durch einen Fehler unseres Aqua-Stop-Systems ein Wasserschaden verursacht werden, so ersetzen wir Schäden privater Gebraucher. Um die Wassersicherheit zu gewährleisten muss das Gerät am Stromnetz angeschlossen sein. 2.