Installation Instructions

ManualsBrandsSiemens ManualsFire - Detectors & PeripheralsTRI-S / TRI-D / TRI-R Dispositifs d’Interface de Déclenchement Intelligents, Feuille de catalogue

P/N 315-049481-5

Models TRI-S, TRI-D, TRI-R

Addressable Interface Modules

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

The Model TRI Series Addressable modules from

Siemens Industry, Inc., shown in Figure 1, interface

direct shorting devices to the MXL System's ALD loop

circuit.

Note: The TRI-S/-D/-R Series is not compatible with

the XL3 System or the XLD-1 loop circuit.

The TRI modules are available in three models. The

TRI-S and TRI-R can monitor a normally open or closed

dry contact. The TRI-S model can only monitor and

report the status of the contact, while the TRI-R incor-

porates an addressable Form C relay. The TRI-D is a

dual input module that supervises and monitors two

sets of dry contacts. It requires two address settings.

The TRI has a multi-color LED that flashes green when

operating normally, amber if the unit is in trouble

condition, and red to indicate a change of state. The

TRI-D flashes twice, once for each address. The TRI-R

red LED indicates a change of state in the relay. The

use of the relay is programmable.

PROGRAMMING INSTRUCTIONS

1. Refer to Figure 2 to locate the openings on the TRI

cover that allow access to the programming holes

which are on the TRI printed circuit board.

2. To connect the TRI to the DPU Device Programming

Unit or the FPI-32 Programmer /Tester, insert the

plug from the cable provided with the programmer

into the opening on the front of the TRI. Be sure to

insert the locating tab on the plug into the slot for the

locating tab on the TRI as shown in Figure 2.

CAUTION: TO PREVENT DAMAGE TO THE

programmer, DO NOT connect a TRI to

the programmer until at least one wire is

removed from terminals 1 or 2 of the TRI.

Note: Connection from the DPU or FPI-32 to the TRI is

keyed. Refer to Figures 5-8 for the proper con-

nections to the control panel.

Figure 2

Inserting the Programmer/Tester Cable

in the TRI Module

Figure 1

TRI Module

SLOT FOR

LOCATING TAB

PROGRAMMING

HOLES

TRI-S/-D/-R

MODULE

PLUG FROM

PROGRAMMER/

TESTER

DPU / FPI-32

LOCATING

TAB

Summary of content (4 pages)

PAGE 1
Installation Instructions Models TRI-S, TRI-D, TRI-R Addressable Interface Modules The Model TRI Series Addressable modules from Siemens Industry, Inc., shown in Figure 1, interface direct shorting devices to the MXL System's ALD loop circuit. Note: The TRI-S/-D/-R Series is not compatible with the XL3 System or the XLD-1 loop circuit. The TRI modules are available in three models. The TRI-S and TRI-R can monitor a normally open or closed dry contact.
PAGE 2
3. (Refer to Figure 3.) Follow the instructions in the DPU User's Manual (P/N 315-033260) or the FPI-32 Programmer/Tester Manual (P/N 315090077) to program the TRI to the following: a. Desired address b. Desired application for fire or proprietary burglary (security) c.
PAGE 3
WIRING ENTERING OUTLET BOX Power Limited Wiring All power limited wiring must enter the outlet box separately from the electric light, power, Class 1, or non-powered limited fire protection signaling conductors. For the TRI-R, wiring to terminal block positions 1, 2, 3, 4, and 5 must enter the outlet box separately from terminals 6, 7, and 8.
PAGE 4
. 5. Supervised switch S1 is on the first programmed address, and Supervised switch S2 is on the second programmed address. Relay contacts are rated: 4A, 125 VAC resistive 4A, 30 VDC resistive Inductive: 3.5A, 120 VAC (0.6P.F.) 3.0A, 30 VDC (0.6 P.F.) 2.0A, 120 VAC (0.4 P.F.) 2.0A, 120 VAC (0.35 P.F.) 2.0A, 30 VDC (0.35 P.F.) The relay is shown in supervisory condition. CAUTION Ground shield wire ONLY at the specified location on the Control Panel. 6.