User Manual

ManualsBrandsSiemens ManualsFire - Detectors & PeripheralsTSM-1X Intelligent Test Switch Module with Dual Isolators, Installation Instructions

Siemens Data Sheet 6198

Building Technologies Division usa.siemens.com/fire

Product Overview

The Siemens

– Fire Safety Intelligent Test Switch Module (Model TSM-1X) is a key-

activated

(T-45), addressable normally open (N.O.) momentary switch with a tri-

color

light-emitting diode (LED) indicator. The tri-

color LED mimics the status of the

associated

Siemens smoke detector or compatible device(s). Each Model TSM-1X

switch

can be configured to test and monitor group of devices, using one (1) address

on the

fire-alarm control panel (FACP) loop.

Model TSM

-1X provides a valid test of a Siemens duct detector – even the detectors

found in inconspicuous, inaccessible areas

–

and will test associated logic functions

of duct housings and other modules. Other common applications include: fan

restart switch; drill switch; recall switch, and remote Arm/Disarm switch.

OTE: Refer to installation manual: P/N – A6V101055486 to ensure Model TSM-1X

compatibility with the Siemens FACPs intended for use in the given application.

Overall, Model TSM

-1X is an economical solution since each X-

series Test Switch

seamlessly provides

combined, pre-packaged functionality of Siemens In/Out

modules (TR

I-S); Siemens status indicators (ILED-series), and T-45 test switches.

Therefore, there is no longer the need of having to buy individual parts and

configuring them in the field. Addition

ally, Model TSM-

1X is modernized through its

capability to provide built

-in isolation, which shows the location of a short.

Specifications

Model TSM

-1X is designed for

use with addressable duct detectors or other intelligent

devices on a Device Loop

Circuit (DLC) of Siemens compatible Fire A

larm Control

Panels (FACP). Turn

-key activation

will cause all associated logic functions to be

tested. Typical applications in which key activation is used include: intelligent duct

detectors | hidden or inaccessible smoke detectors | Fan, Recall, Restart, Drill and

remote Arm/Disarm switches. This alarm

condition will cause all logic associated with

the duct detector to activate. The TSM

-1X is mounted in a 3.5-inch

(8.9 cm.) deep

single

-gang back box, which is supplied-by-others (BO).

Mod

el TSM-1X supports two (2) operation methods:

 Polarity insensitive mode

 Isolator mode

The module can be wired in either mode and configured by the

compatible Siemens FACP.

While in isolation, the built in dual

isolators will w

ork at both sides of the module to isolate a line

short in front or behind the modu

le.

Model TSM

-1X provides intelligent built-in, dual isolation,

meeting Class X (Style 7) survivability requirements for shorts

while providing reliable alarm communication

to the Siemens

CP. Additionally, Model TSM-1X allows up to 190 isolators per

loop, and up to 30 devices between isolators (wired in polarity

insensitive mode). The devices between isolators can either be

pre

-existing `H’-series or later `X’ generation devices.

Peripheral and Detection Devices

Initiating Device

Intelligent Test Switch and Status Indicator

Model TSM-1X

Architect & Engineer Specifications

 Intelligent test-switch module with

momentary, normally open (N.O.)

turn-key activated (T45) switch

 Dual, built-in isolators

 Meets Class X (Style 7)

survivability requirements

 Multi-color light-emitting diode

(LED) indicates system status:

- G

REEN | AMBER | RED

 Low current draw

 Restriction of Hazardous

Substances (RoHS) compliant

 Mounts in a single-gang box:

- 3.5 inches (8.9 cm.) deep

 Device Programmer / Tester

(Model DPU) programs and

verifies device’s address:

- programming capabilities include

testing a duct detector, as well as

other Siemens addressable devices

 Capability of being installed

anywhere on a communication loop,

or on the wiring of that loop

 UL864 | UL2572 | UL2017 Listed;

CAN/ULC-S527 & CAN/ULC-S576 Listed

- File S24304, Vol. 3

Model TSM-1X

Duct Detector Test Switch

Summary of content (4 pages)

PAGE 1
Peripheral and Detection Devices Initiating Device Intelligent Test Switch and Status Indicator Model TSM-1X Architect & Engineer Specifications  Intelligent test-switch module with momentary, normally open (N.O.
PAGE 2
1. TSM-1X faceplate 2. Single-gang switchbox (user supplied) 1 NOTES: The single-gang electrical box, seen in this CGI depiction, is supplied-by-others (BO). Specifications – (continued) The isolation feature found on a Model TSM-1X Test Switch provides a location of the fault (short). When a short occurs, the Siemens FACP can identify the fault automatically and the module recognized the short location (in front of the device or behind the device).
PAGE 3
Compatibilities The `X’-series modules may be used, along with Model `H’-series intelligent detectors; Model `HMS’-series addressable manual stations, or any other `H’-series addressable intelligent module (e.g. Model HZM or Model HCP). Interspersing Siemens `X’ and `H’-series detection devices on the same loop is mostly permitted, but there are exceptions: Models HLIM (isolation module) and SBGA-34 (audible base) cannot be used with `X’ devices on the same loop.
PAGE 4
NOTICE – The information contained in this data-sheet document is intended only as a summary, and is subject to change without notice. The product(s) described here has/have a specific instruction sheet(s) that cover various technical, limitation and liability information. Copies of install-type, instruction sheets – as well as the General Product Warning and Limitations document, which also contains important data, are provided with the product, and are available from the Manufacturer.