Commissioning Instructions
Table Of Contents
- 1 Functions
- 2 UI description
- 2.1 Home Page (Navigation function)
- 2.2 Multifunction page
- 2.3 General temperature control page
- 2.4 VRF air conditioner function page
- 2.5 Floor heating function page
- 2.6 Ventilation system function page
- 2.7 RGB dimming function page
- 2.8 Energy metering display function page
- 2.9 Air quality display function page
- 2.10 Background music function page
- 2.11 Setting page
- 2.12 Screen
- 2.13 Administrator function via password
- 2.14 Administrator function via bus
- 2.15 Other pages
- 3 Parameters and communication objects
- 3.1 "General" interface
- 3.2 "Home page" interface
- 3.3 "Function page" interface
- 3.3.1 "Page settings" parameters
- 3.3.2 "Function page" communication objects
- 3.3.3 "Page x - Multifunction (Lighting/Blind/Scene/Value send)" parameters and communication objects
- 3.3.4 "Page x - General Temp. Control" parameters and communication objects
- 3.3.5 "Page x - Enhanced Floor Heating" parameters and communication objects
- 3.3.6 "Page x - VRF interface & Operation" parameters and communication objects
- 3.3.7 "Page x - Ventilation System" parameters and communication objects
- 3.3.8 "Page x - Air Quality display" parameters and communication objects
- 3.3.9 "Page x - Energy Metering Display" parameters and communication objects
- 3.3.10 "Page x - RGB Dimming" parameters and communication objects
- 3.3.11 "Page x - Background Music" parameters and communication objects
- 3.4 "Timer function" interface
- 3.5 "Event Group function" interface
- 3.6 "Logic function" interface
- 4 Icons
- 5 Appendix
Parameters and communication objects
"Logic function" interface
3
A6V12035440_en--_c
105 | 121
3.6.4 "Threshold comparator" parameters and communication
objects
Parameters
Name
Description
Range
Logic operation
Sets the logic operation Threshold comparator
-
Data type of output value
This is used to set the data type of the threshold value.
4bit
1byte
2byte
4byte
Threshold value [0...255]
This is used to set threshold value. The value range is
determined by the data type selected.
Data type of output value =
4bit: 0...15
Data type of output value =
1byte: 0...255
Data type of output value =
2byte: 0...65535
Data type of output value =
4byte: 0...4294967295
If Object value<Threshold
value
If Object value=Threshold
value
If Object value!=Threshold
value
If Object value>Threshold
value
If Object value<=Threshold
value
If Object value>=Threshold
value
These parameters are used for setting the sending value at
different scenarios between Object value and threshold value.
If there is a conflict between the commands, the value sent
should be the one which fulfill the last scenario.
E.g.: if the parameters are set as follows:
● "If Object value=Threshold value" is set to "Send value
0";
● "If Object value<=Threshold value" is set to "Send value
1"
● when the object value = threshold value, then the logic
result sends "1"
Do not send telegram
Send value '0' Send value '1'
Send result when
This is used to set the trigger of sending the logic result.
Note: For the first logic calculation, the result is sent even if it
has no change.
New input received
Object value changes
Time delay of sending: base
[s]
This is used to set the time delay for sending the logic result to
bus. Time delay=Base [s] Factor
If option "None" is selected, then there is no time delay.
None
0.1s
1s
2s
5s
10s
25s
Time delay of sending: factor
[1...255]
This is used to set the time delay for sending the logic result to
bus. Time delay=Base [s] Factor
1...255