Commissioning Instructions
Table Of Contents
- 1 Functions
- 2 UI description
- 2.1 Home Page (Navigation function)
- 2.2 Multifunction page
- 2.3 General temperature control page
- 2.4 VRF air conditioner function page
- 2.5 Floor heating function page
- 2.6 Ventilation system function page
- 2.7 RGB dimming function page
- 2.8 Energy metering display function page
- 2.9 Air quality display function page
- 2.10 Background music function page
- 2.11 Setting page
- 2.12 Screen
- 2.13 Administrator function via password
- 2.14 Administrator function via bus
- 2.15 Other pages
- 3 Parameters and communication objects
- 3.1 "General" interface
- 3.2 "Home page" interface
- 3.3 "Function page" interface
- 3.3.1 "Page settings" parameters
- 3.3.2 "Function page" communication objects
- 3.3.3 "Page x - Multifunction (Lighting/Blind/Scene/Value send)" parameters and communication objects
- 3.3.4 "Page x - General Temp. Control" parameters and communication objects
- 3.3.5 "Page x - Enhanced Floor Heating" parameters and communication objects
- 3.3.6 "Page x - VRF interface & Operation" parameters and communication objects
- 3.3.7 "Page x - Ventilation System" parameters and communication objects
- 3.3.8 "Page x - Air Quality display" parameters and communication objects
- 3.3.9 "Page x - Energy Metering Display" parameters and communication objects
- 3.3.10 "Page x - RGB Dimming" parameters and communication objects
- 3.3.11 "Page x - Background Music" parameters and communication objects
- 3.4 "Timer function" interface
- 3.5 "Event Group function" interface
- 3.6 "Logic function" interface
- 4 Icons
- 5 Appendix
Parameters and communication objects
"Function page" interface
3
A6V12035440_en--_c
61 | 121
No.
Name
Object function
Length
Flag
Data type
181
Page x-Temp. Cntrl
(send)
Fan speed low
Fan speed
1 bit
1 byte
CT
1.001 switch
5.001 percentage
(0...100 %)
Fan speed can send control telegrams of the fan speed to bus via four 1bit objects (objects 181,182,183,184) or one 1byte
object "Fan speed".
1 bit: The corresponding fan speed is activated on the screen, and the corresponding object sends telegram "1" to the bus,
except for the telegram sending 0 of the fan speed.
1byte: The corresponding telegram value of each fan speed is defined by the parameter. Activate the corresponding fan speed
on the screen, and object 181 sends the corresponding telegram value of the fan speed to bus.
182
Page x-Temp. Cntrl
(send)
Fan speed medium
1 bit
CT
1.001 switch
The communication object sends control telegrams of the fan speed medium to bus.
183
Page x-Temp. Cntrl
(send)
Fan speed high
1 bit
CT
1.001 switch
The communication object sends control telegrams of the fan speed high to bus.
184
Page x-Temp. Cntrl
(send)
Fan speed off
1 bit
CT
1.001 switch
The communication object sends control telegrams of the fan speed off to bus.
185
Page x-Temp. Cntrl
(send)
Fan speed auto
1 bit
CT
1.003 enable
The communication object is used for sending the automatic control telegram of the fan speed to bus. Telegram value:
0: Cancel automatic
1: Automatic
186
Page x-Temp. Cntrl
(send / receive)
Power On/Off
1 bit
CWTU
1.001 switch
The communication object is used to switch and control the HVAC function of the device, and the corresponding control is
turned off when the HVAC is turned off.
187
Page x-Temp. Cntrl
(send)
Base setpoint (°C)
2 bytes
CRT
9.001 temperature
(℃)
● Room operation mode is disabled, the communication object is used to send the base value of the set temperature.
● Room operation is enabled and
– The temperature is set to "Base setpoint + setpoint shifting", the communication object is used to send the base
value of the set temperature, i.e., the temperature setting value of Comfort mode, and the setting temperature of
Standby mode and Economy mode changes according to the relative change. In Protection mode, only the
temperature setting value of the protection mode is modified.
– The temperature is set to "Absolute setpoints", the communication object is used to send the temperature setting
value of the current room operation mode.