User Manual

ManualsBrandsSiemens ManualsFire - Alarm EquipmentVPM VESDA Peripheral Module, Installation Instructions

SiemensSiemens

Siemens

Industry Industry

Industry

Inc. Inc.

Inc.

SmarSmar

Smar

t Infrastructt Infrastruct

t Infrastruct

ureure

ure

A6V10347523_en--_e

INTRODUCTION The Model VPM from Siemens Industry, Inc. is an HNET module that interfaces to a

VESDA® HLI High Level Interface. The VPM must be mounted on a VPM-MP mount-

ing plate (S54430-F95-A2) inside a CAB enclosure with an HLI card and a socket card

(VESDA-HLI-Kit S54430-F99-A2). See

Table 1 for a list of compatible VESDA®

detectors and the limitations on the

number of detectors per HLI. One VPM

can support two VESDA-HLI-Kits and a

total of 200 VESDA® detectors.

The VPM uses one network address on

the FireFinder-XLS/Desigo Fire Safety

Modular/Cerberus PRO Modular System.

All VESDA® detectors connected to the

VPM are addressed using a VESDA®

programmer. For ease of use and troubleshooting

purposes, be sure that the address assigned to the VESDA® detector in Zeus agrees

with the address assigned to it by the VESDA® programming tool. The VPM commu-

nicates the status of the VESDA® devices over HNET to the FireFinder-XLS/Desigo

Fire Safety Modular/Cerberus PRO Modular System where it can be displayed on the

Operator Interface (OI).

Features VPM features are as follows:

• Can be connected to the HNET either Style 4 or Style 7.

• Includes diagnostic LEDs to indicate failure of the HNET or the CPU. It also

has a power on indicator.

• Includes a reset switch in the event that the VPM requires a hardware reset.

• Mounts inside any CAB enclosure on a VPM-MP mounting plate.

• Supports one or two VESDA® HLIs.

• VPM software can be upgraded in the field from a PC that has the Zeus

program installed.

OPERATION The VPM initializes, operates, and maintains all devices residing on the VESDAnet®

network. The VPM communicates all relevant device and event information, such as

alarms and troubles, to the OI. The sensitivity of any VESDA® detector can be

checked from the OI through the VPM. All information about the devices on the loop

can be displayed on the OI.

The VPM supports two HLI interface cards. Up to 100 VESDA® detectors can

connect to each HLI. The VESDAnet® microprocessor controls the on-board isolator

to isolate either zone from the VESDAnet® loop if one of them is shorted. When one

zone is isolated from the loop, the other zone will still work.

Figure 1

VPM VESDA® Interface Module

VESDA® Peripheral Module

Installation Instructions

Model VPM

Summary of content (12 pages)

PAGE 1
Installation Instructions Model VPM VESDA® Peripheral Module INTRODUCTION The Model VPM from Siemens Industry, Inc. is an HNET module that interfaces to a VESDA® HLI High Level Interface. The VPM must be mounted on a VPM-MP mounting plate (S54430-F95-A2) inside a CAB enclosure with an HLI card and a socket card (VESDA-HLI-Kit S54430-F99-A2). See Table 1 for a list of compatible VESDA® detectors and the limitations on the number of detectors per HLI.
PAGE 2
Controls and Indicators The HNET/UFP side panel of the VPM contains one reset switch, three LEDs, one termination switch and one HNET address switch as shown in Figure 2. A reset switch is located on the top of the panel. Pushing the reset switch re-initializes the VPM operation. POWER (Green) Normally ON. When illuminated, indicates that power for the VPM is applied to the module. CPU FAIL (Yellow) Normally OFF. When illuminated, indicates that the module microprocessor has failed.
PAGE 3
Configuring VESDAnet for use with the VPM In order to comply with UL/ULC timing requirements for supervision of the VESDA detectors on VESDAnet, two supervision parameters must be set. While logged on and configuring the VESDAnet system with the Xtralis VSC program, perform the following steps: 1. In the tree view, right click on “VESDAnet” (the root of the tree). 2. Select “edit” from the pop-up menu. 3. In the pop-up window, select the “Network Settings” tab. 4.
PAGE 4
EARTH GROUND +24V NOTES: 1. 18 AWG min., 12 AWG max. 2. Power limited to NFPA72 per NEC 760. 3. No end of line device required. 4. Reference PSC-12 Installation Instructions, P/N 315-033060, or PSX-12 Installation Instructions, P/N 315-031120. 24V RET C - + H 24V A S S I S SOCKET + - +X5- CARD #1 TB3 X1 +X4- VPM PSC-12 OR PSX-12 SOCKET +X5- CARD #2* SEE FIGURE 5 FOR WIRING DETAIL X1 PORT 1 PORT 2 RS-232 RS-232 +X4* OPTIONAL 15-PIN CABLE Only one power supply, PSC-12 or PSX-12 is allowed.
PAGE 5
CABLE PROVIDED WITH THE VESDA-HLI-KIT P/N S54430-F99-A2 1 2 PORT 3 SPP PORT 1 3 4 5 6 TXD PORT 1 RS-232 7 GND RTS PORT 2* RS-232 CTS RXD GND GREEN 3 BLACK 5 ORANGE 7 WHITE 8 RED 2 GREEN 3 BLACK 5 ORANGE 7 WHITE 8 TO HLI #1 TO HLI #2** **OPTIONAL 10 RTS 10 CTS 8 9 TXD PORT 2 RS-232 2 1 RXD RED * 1 RCV+ RCVPORT 2 RS-485 TO ENABLE PORT 2 (RS-232), THE PORT 2 SELECT PINS (6 AND 7) MUST BE JUMPERED ON THE PORT 2 RS-485 CONNECTOR.
PAGE 6
Table 1: VESDAnet® COMPATIBLE DEVICES NODES ELEMENTS NODES ELEMENTS VLF-250*/** 1 1 VLF-500* 1 1 VLS-200 1 5 VLS-300 1 5 VLC-505 1 1 VLS-600 1 5 VLP-400 VLP-010 1 1 VLS-700 1 5 1 1 VLS-204 1 5 VLP-002 1 1 VLS-304 1 5 VLS-310 1 5 VLS-214 1 5 VLS-314 1 5 LaserFOCUS LaserCOMPACT LaserPLUS DETECTORS VLP-012 VESDA-E 1 1 VEP-A00-1P**** 1 1 VEP-A00-P*** 1 1 VEP-A10-P*** 1 1 VLS-210 1 5 VEU-A00*** 1 1 VES-A00-P***** 1 5 VEU-A10*** 1 1 VES-A1
PAGE 7
SUPERVISED & POWER LIMITED SHIELD DO NOT USE 1 2 9 3 10 4 11 12 5 6 13 7 14 8 15 1 16 20 21 22 23 1 6 24 NIC-C INSTALLED IN THE CC-5 Figure 8 VPM In The Middle Of A Style 4 HNET 2 9 3 10 4 11 5 12 6 13 7 14 8 15 16 23 24 DO NOT USE NOTES: 1. No end of line resistor required. VPM termination set to OFF. 2. 18 AWG min., 12 AWG max. 3. 2000 feet max. between NIC-Cs. 4. Use twisted pair or shielded twisted pair. 5. Terminate shields at one end only. 6.
PAGE 8
SUPERVISED & POWER LIMITED SHIELD DO NOT USE NOTES: 1. No end of line resistor required. VMP termination set to ON. 2. 18 AWG min., 12 AWG max. 3. 2000 feet max. for NIC-C. 4. Use twisted pair or shielded twisted pair. 5. Terminate shield at one end only. 6. Power limited to NFPA72 per NEC 760. 7. Reference NIC-C Installation Instructions, P/N 315033240 for wiring and ground fault detection impedance.
PAGE 9
1 3 SOC K CAR ET D VPM SOC K CAR ET D 2 HLI # 2 HLI # 1 Legend: 1 Typical CAB enclosure 2 VPM-MP mounting plate 3 Keyholes for mounting VPM-MP using four #10-32 x 3/8 pan Phillips screws Figure 11 Mounting the VPM-MP in a Typical CAB Enclosure ELECTRICAL RATINGS VPM HLI (each) 24V Back Plane Current N.A. N.A. Screw Terminal 24V Current 50mA Max. 110mA Max. 6.2V Back Plane Current N.A. N.A. 50mA Max. 110mA Max.
PAGE 10
CC-2 TB1 P5 + - TB3 P4 P10 PSC-12 RESET VPM POWER MODULE FAIL TAMPER SWITCH CAN FAIL H - NET FAIL GND FAULT 24V 12 FAIL 24V 4A FAIL HNET/CAN O — ON OFF BATTERY _ + P9 TB2 TB4 1 + P12 GND 2 N _ H Battery VPM PTB VPM A.C.
PAGE 11
CYBER SECURITY DISCLAIMER Siemens provides a portfolio of products, solutions, systems and services that includes security functions that support the secure operation of plants, systems, machines and networks. In the field of Building Technologies, this includes building automation and control, fire safety, security management as well as physical security systems.
PAGE 12
Siemens Industry, Inc. Smart Infrastructure Florham Park, NJ Siemens Canada, Ltd.