Manual

ManualsBrandsSierra Wireless ManualsMobile Phones20070914

PinPoint X HSDPA

for AT&T

User Guide

20070914

Rev 3.0B

Summary of content (203 pages)

PAGE 1
PinPoint X HSDPA for AT&T User Guide 20070914 Rev 3.
PAGE 2
Preface Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost.
PAGE 3
Preface DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY.
PAGE 4
Preface Contact Information Support Desk: Phone: 1-877-231-1144 Hours: 5:00 AM to 5:00 PM Pacific Time, Monday to Friday, except US Holidays E-mail: support@sierrawireless.com Sales Desk: Phone: 1-510-781-4200 1-604-232-1488 Hours: 8:00 AM to 5:00 PM Pacific Time E-mail: MobileandM2Msales@sierrawireless.com Post: Sierra Wireless America 3159 Corporate Place Hayward, CA USA 94545 Sierra Wireless 13811 Wireless Way Richmond, BC Canada V6V 3A4 Fax: 1-510-781-4299 1-604-231-1109 Web: www.sierrawireless.
PAGE 5
Contents Introduction to the PinPoint X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 ALEOS™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 AceWare™. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AceManager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 6
Contents Hardware Installation of the PinPoint X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 GPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Connecting to Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Connecting to a Computer or other Device . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 7
Contents Data Communication and Host Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Basic Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Serial Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Data Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 8
Contents National Marine Electronics Association (NMEA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Trimble ASCII Interface Protocol (TAIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Datum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Before you Configure GPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 9
Contents SNMP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 Listening Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 Security Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 User Name and Password . . . . . . . . . .
PAGE 10
Contents *DPORT=n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 *HOSTPAP=n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 *NETALLOWZEROIP=n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 *NETPW=pw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 11
Contents *USD=n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 *DNSn=d.d.d.d . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 *DNSUPDATE=n . . . . . . . . . . . . . .
PAGE 12
Contents *TQUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 Low Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 PTMR=n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 SISE=n . . . . . . . . . . . . . . . .
PAGE 13
Contents *DIGITALINn?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 *IOSTATE=n,s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 *RELAYOUTn=x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 Edge/HSDPA . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 14
1: Introduction to the PinPoint X • ALEOS™ • AceWare™ • Connecting to the AT&T Network • HSDPA Communication 1 The PinPoint X is a compact, intelligent and fully‐featured mobile communications platform with multiple peripheral connections including serial, Ethernet and USB. Expanded I/O functionality in a separate connector includes four digital inputs, four analog inputs and two relay outputs unleashing extensive remote instrumentation possibilities.
PAGE 15
Introduction to the PinPoint X • Real‐Time GPS Reporting • GPS Store and Forward • Packet Level Diagnostics • Device Management & Control • Protocol Spoofing Figure 1-2: Powered by ALEOS AceWare™ A wireless solution is not complete until you have software tools to manage the devices monitoring your valuable equipment. AceWare™ is the device management and monitoring application suite for Sierra Wireless AirLink products powered by ALEOS.
PAGE 16
Introduction to the PinPoint X Figure 1-3: AceManager Simplified Deployment AceManger provides the ability to remotely set up and configure your Sierra Wireless AirLink products. Remote device setup and configuration reduces the deployment timeline of your wireless solution and provides a quicker path to ROI. Templates allow you to easily configure other devices in your fleet with identical settings, ensuring a simple, accurate deployment.
PAGE 17
Introduction to the PinPoint X AceNet AceNet, the enterprise grade productivity enhancing tool, enables you to efficiently deploy and monitor Sierra Wireless AirLink products on a large scale. Figure 1-4: AceNet Network Monitoring AceNet allows you to efficiently deploy, monitor, and maintain wireless networks of any size by enabling you to quickly configure an entire group of Sierra Wireless AirLink modems to the same parameter settings using templates built with AceManger.
PAGE 18
Introduction to the PinPoint X Modem Doctor Modem Doctor is a troubleshooting and diagnostics utility. This utility will allow you to get a log file of the PinPoint X activity which you can then send to Sierra Wireless support, erase the current configuration completely., and temporarily set the PinPoint X to a known configuration to aid in trouble shooting (SOS mode). Rev 3.0B Feb.
PAGE 19
Introduction to the PinPoint X Figure 1-6: Modem Doctor Modem Doctor USB 1. Open the ModemDoctorUSB.exe. 2. Select any one option. Note: If you are using USB port as serial, then USB device is set to “o” and if you are using the default option then the USB device is set to “1”. The available port is automatically detected. Passsword is the fault password. 3. Press Erase. The modem will then reset. Note: If you erase the fatory defaults will be restored. USBnet is the factory default port. Rev 3.
PAGE 20
Introduction to the PinPoint X Figure 1-7: Modem Doctor: USB connection Connecting to the AT&T Network The PinPoint X uses AT&T as an ISP (Internet Service Provider) to connect you to the Internet. Steps of a connection: Rev 3.0B Feb.08 1. When your PinPoint X is powered on, it automatically searches for cellular service using HSDPA or EDGE. 2.
PAGE 21
Introduction to the PinPoint X Figure 1-8: Connecting to the Internet The PinPoint X will perform a one‐to‐one routing for all internet traffic to and from the computer or other end device. One‐to‐one means that your PinPoint X will provide a connection for one device to the Internet at a time. In Private Mode, the PinPoint X will provide NAT (Network Address Translation) for the computer or other end device.
PAGE 22
Introduction to the PinPoint X address for your modem, you can use a Dynamic DNS service (such as IP Manager) to translate your IP address into to a domain name. Caution: If you want to connect remotely to your PinPoint X using TCP/IP, the IP address given to your modem by AT&T cannot be a private or internal IP address (such as a custom APN) unless you are on the same network or inside that network’s firewall (such as with frame relay).
PAGE 23
Introduction to the PinPoint X EDGE EDGE (Enhanced Data rates for GSM Evolution) provides end‐ to‐end packet data services with an enhanced connectivity building on GPRS technology and using the established GSM networks. EDGE provides higher transmission rates and better transmission quality for data than GPRS. EDGE can carry data at speeds typically up to 384 kbit/s in packet mode.
PAGE 24
2: Specifications 2 • Interface Port Pin-Outs • Power Connector Features and Benefits • Embedded Intelligence • Low Power Consumption • High‐Speed Processor • High‐Speed 2‐way Data • Multiple Interfaces, I/O Port • High‐Sensitivity GPS Receiver • Persistent Network Connectivity • Remote Management and Configuration • Extensive Vehicle Telemetry • Integrated with 3rd Party Tracking Applications • Rugged for Extreme Environments Technology • HSDPA With Fallback to: · UMTS · GSM EDGE ·
PAGE 25
Specifications • Input Voltage 9 ‐ 28V DC Standards/Approvals • Carrier specific approvals • FCC • Industry Canada Host Interfaces • Ethernet: 10/100 Mbps RJ‐45 • USB Type B • RS‐232: DB9 DCE (300‐230400 baud) • I/O: 4 Digital, 4 Analog, 2 Relay • Antenna Connection: · Cellular ‐ 50 Ohm TNC · GPS ‐ 50 Ohm SMA Dimensions • 135mm x 38mm x 91mm • 612 grams Application Interfaces • TCP/IP, UDP/IP, DHCP, HTTP, SNMP, SMTP, SMS, MSCI, NMEA, TAIP, GPS, and more LED Indicators • Network •
PAGE 26
Specifications I/O Port 22 21 20 19 DIN1 GND DIN3 DIN2GND DIN4 11 10 9 18 17 16 15 14 13 12 Relay 1 Rsv NC AIN1 GND AIN3 NO1Com1 Relay 2 Rsv NC AIN2 GND AIN4 NO2Com2 8 7 6 5 4 3 2 1 Figure 2-2: PinPoint X I/O Port Diagram (not to scale) Table 2-1: PinPoint X I/O Port Pin-out 1. Analog Input 4 12. Analog Input 3 2. Analog Ground 13. Analog Ground 3. Analog Input 2 14. Analog Input 1 4. No Connect 15. No Connect 5. Reserved for future use 16. Reserved for future use 6.
PAGE 27
3: Activating PinPoint X on AT&T 3 Network • Installating the SIM • Configuring the APN This chapter provides step‐by‐step directions for activating your PinPoint X on the AT&T cellular network. Installating the SIM The SIM in the PinPoint X is a smartcard securely storing the key identifying a cellular subscriber. Generally, you will only need to install a SIM once in the life of the modem and it may be pre‐installed by your Sierra Wireless Representative. 1.
PAGE 28
Activating PinPoint X on AT&T Network Tools Required • Small Phillips screw driver ‐ The Phillips screw driver is the one which is also called a plus (+) or X screw driver. • Slim stylus ‐ A PDA stylus, an unbent paperclip, or other such item. 2. Opening the SIM Slot a. Unplug the PinPoint X power and all cables. b. Remove slot cover on the front of the PinPoint X to reveal the SIM slot. Figure 3-1: Slot Cover 3. a. Carefully remove the SIM card from the card you got from AT&T. 4.
PAGE 29
Activating PinPoint X on AT&T Network Figure 3-3: Sample of a Card with SIM Figure 3-4: Insert SIM in to the modem b. Place the SIM into the tray and gently press to click it into place. Figure 3-5: Empty SIM Tray and a Tray with a Sample SIM 6. Insert the Tray and SIM a. Slide the tray back into the modem. b. Gently press to click it into place. Tip: The top of the card faces the bottom of the modem. Rev 3.0B Feb.
PAGE 30
Activating PinPoint X on AT&T Network Figure 3-6: Inserting the SIM 7. Finishing the SIM installation Replace the cover to prevent dust or other unwanted particles from entering the PinPoint X. Once the cover is replaced, the installation is complete. Note: The first time you power on your Raven-E with your new SIM, there may be a delay of up to 10 minutes for the initial network connection to occur.
PAGE 31
Activating PinPoint X on AT&T Network 1. Start AceManager Start > All Programs > AirLink Communications > AceManager 3G > AceManager 3G Figure 3-7: AceManager 2. Connect to the Modem a. Click the Connect button. b. Select a connection method: · If you are connecting locally with the modem connected directly to your computer using a serial cable, you can use PPP. · If you are connecting locally with the modem connected directly to your computer using an Ethernet cable, you can use UDP, TCP, or Ethernet.
PAGE 32
Activating PinPoint X on AT&T Network d. Enter the password. The default password will be entered for you. e. Select OK. 3. Enter the APN a. Select EDGE/HSDPA from the menu on the left side of AceManager (under “Groups”) Figure 3-8: AceManager : EDGE/HSDPA b. Type your APN in the New Value field of *NETAPN. Figure 3-9: AceManager : EDGE/HSDPA - *NETAPN Optional: If you need to configure your modem for a cus‐ tom APN, after entering the APN, there is additional infor‐ mation you will need to enter. 1.
PAGE 33
Activating PinPoint X on AT&T Network Figure 3-10: AceManager : Misc 2. Enter the NAI into the new value field for *NETUID and enter your network password into the new value field for *NETPW. Figure 3-11: AceManager : Misc - *NETUID, *NETPW 4. Write the Settings to the PinPoint X a. Click the Write button on the tool bar of AceManager. b. Wait for the message “Write Successful” to appear in the status bar. Figure 3-12: AceManager : Write c. Rev 3.0B Feb.08 Reset the PinPoint X.
PAGE 34
4: Hardware Installation of the PinPoint X • Connecting to Power • Connecting to a Computer or other Device • Indicator Lights • Mounting 4 Your PinPoint X should be mounted in a position that allows easy access for the cables so they are not bent, constricted, in close proximity to high amperage, or exposed to extreme temperatures. The LEDs on the front panel should be visible for ease of operational verification.
PAGE 35
Hardware Installation of the PinPoint X radio communications regulations of the Federal Communica‐ tions Commission (FCC), Industry Canada, or your country’s regulatory body (if used outside the US). Your PinPoint X will work with most Dual‐Band PCS cellular antennas with a connector that works in the high and low frequencies of the cellular technology of your modem. Connect the primary antenna or primary RF cable directly to the antenna connector on the back of the PinPoint X.
PAGE 36
Hardware Installation of the PinPoint X Connecting to Power Your PinPoint X can be used with either DC, available in most automobiles, or 110 AC, standard US wall power, with the appropriate power adapter. DC cables and AC adapters are available as optional accessories in addition to the one included with your PinPoint X.
PAGE 37
Hardware Installation of the PinPoint X connecting the modem to a hub or switch you should use a straight through cable or use the uplink port on the hub or switch with a cross‐over cable. Figure 4-5: Serial The serial port can be connected directly to most computers or other devices using a standard straight through cable. If you have a DCE device, you will need a null modem or null modem cable. Figure 4-6: USB Your PinPoint X’s full‐speed (12 Mbit) USB 2.
PAGE 38
Hardware Installation of the PinPoint X The I/O port can use an optional I/O harness available through Sierra Wireless. Indicator Lights When your PinPoint X is connected to power and an antenna, there is a specific pattern to the lights to indicate its operation mode. Figure 4-8: PinPoint X Indicator lights • Network ‐ Indicates a successful connection to the cellular network with an IP address given and a channel acquired.
PAGE 39
Hardware Installation of the PinPoint X • The Reset button (on the left side of the PinPoint X) has two functions. If it is quickly depressed and released, the modem will simply power cycle the internal hardware. If, however, the reset is depressed and held for several seconds (count 10 slowly, and wait for the power light to go off after the light pattern stops), the ALEOS configu‐ ration settings will return to the factory defaults.
PAGE 40
Hardware Installation of the PinPoint X 6.12”(155.4mm) .132”(3.3mm) 2.935” (74.5mm) .267”(6.78mm) 3.185” (80.89mm) 2.5” (65mm) .315”(8mm) R.14”(3.5mm) .565”(14mm) R.075”(1.9mm) 6.37”(229mm) Front Figure 4-9: Diagram of the PinPoint X base Rev 3.0B Feb.
PAGE 41
5: Configuring your PinPoint X • Using AceManager • Using Templates • Using a Terminal Application with AT Commands 5 With ALEOS as its “brain”, the PinPoint X is a highly configu‐ rable device, more than just a “dumb” modem. To configure your PinPoint X, you have two options. You can use the configuration and management applications of the AceWare suite or you can use a terminal emulator application such as HyperTerminal, PuTTY, or many others.
PAGE 42
Configuring your PinPoint X Figure 5-1: AceManager 2. Connect to your PinPoint X a. Click the Connect button. Figure 5-2: AceManager : Connect to Modem b. Select a connection method: · If you are connecting remotely, you can use UDP, TCP, or SMS. · If you are connecting locally with the modem connected directly to your computer using a serial cable, you can use PPP.
PAGE 43
Configuring your PinPoint X e. Select OK. Figure 5-3: AceManager : Connected 3. Enter the configuration options a. On the left side of AceManager is the Groups menu. Select the appropriate group as needed or directed. b. Enter your changes in the New Value column by typing in the desired change or using the drop down menus. c. The current configuration is shown in the Value column. Figure 5-4: AceManager : Changing values Rev 3.0B Feb.
PAGE 44
Configuring your PinPoint X 4. Write the changes to the modem a. Click the Write button on the tool bar of AceManager. b. Wait for the message “Write Successful” to appear in the status bar. Figure 5-5: AceManager : Write Tip: Some configuration settings will require you to reset the modem before they will take effect. You can reset the modem by using the Reset button in AceManager or by using the reset button on the modem. You can also reset the modem by cycling the power.
PAGE 45
Configuring your PinPoint X Note: Some of the configuration settings are specific to individual modems. You do not want to have those settings in your saved template otherwise the modems you configure with the template could cease to work with the cellular or local network. · Cellular Technology specific settings ( EDGE/HSDPA group) · *MODEMNAME · *HOSTPRIVIP · *HOSTPEERIP · *HOSTUID · *HOSTPW d. Click the Save button on the toolbar. e.
PAGE 46
Configuring your PinPoint X 2. Applying a Template to one modem with AceManager You can use a template you created yourself, using the steps above, or a template provided by your AirLink representative or someone in your company who has set up a modem template. The template you wish to apply must be saved to your hard drive. a. Load the template. 1. Connect to the modem you want to configure using AceManager. 2. Click on the Load button on the toolbar. Figure 5-8: AceManager : Load 3.
PAGE 47
Configuring your PinPoint X Tip: You can use common settings on one modem to configure those same settings on another modem even of a different type. For example, you can use the serial settings of a modem (such as PinPoint X or Raven X) to configure the serial settings of a PinPoint X. Settings not applicable to the modem on which you are loading the template, will be discarded. 3.
PAGE 48
Configuring your PinPoint X Figure 5-10: AceNet : Selected modems Tip: Click on the first with your mouse and, with the control button held down, click the additional modem. b. Select the Modem option in the tool bar and then select Apply AceManager Template. Figure 5-11: AceNet : Modem menu c. Either type in the Template file name, or click browse and select the template file you want to apply (you may need to change folders). Figure 5-12: AceNet : Template select d.
PAGE 49
Configuring your PinPoint X Using a Terminal Application with AT Commands You can access and configure your PinPoint X using a terminal application such as Microsoft HyperTerminal, PuTTY, or similar. The following directions are for HyperTerminal which is part of a standard installation of Windows XP. Start > All Programs > Accessories > Communications > HyperTer‐ minal Figure 5-13: HyperTerminal 1. Choose a name and icon for your connection. a.
PAGE 50
Configuring your PinPoint X 2. Connect To Using Serial: a. Select COM1, or the comport to which the modem is connected, for the “Connect Using”. Figure 5-14: Connect To Using Ethernet: a. Select TCP/IP (Winsock) for “Connect Using”. b. Type in 192.169.13.31 for Host Address. c. Change the “Port Number” to 2332. d. Select OK. 3. Port Settings (serial only) a. Change or verify the settings: Rev 3.0B Feb.
PAGE 51
Configuring your PinPoint X · · · · · Bits per Second: 115200 (default) Data Bits: 8 Parity: None Stop Bits: 1 Flow Control: Hardware. Figure 5-15: Port Settings Tip: If you have configured the PinPoint X for settings different than the defaults for Bits per Second, Data Bits, Parity, and/or Stop Bits, you will need to use your changed settings. b. Select OK. Rev 3.0B Feb.
PAGE 52
Configuring your PinPoint X 4. Connected Figure 5-16: HyperTerminal : TCP/IP connected a. If you are prompted for a password, enter 12345. Tip: You will not be prompted for a password if you connect using a COM port. b. Type AT and press Enter. You should get a reply of “OK” or “0”. c. To see what you are typing as you type it, you will need to turn on the echo and verbose mode. Type ATE1V1 and press Enter. d. If you get a reply of “OK”, then you entered the command successfully.
PAGE 53
Configuring your PinPoint X • Required variable parameters are denoted with italicized text, example, Dn. The n is variable. • Acceptable parameters and/or specific formats are listed with each command. • Most commands with parameters can be entered with ? to read the current value (for example, AT&D? will respond with “2” if the default has not been changed). • Optional parameters are denoted with square brackets [ ]. • AT Commands are not case sensitive.
PAGE 54
6: Universal Serial Bus (USB) • Changing the USB port communication • Installing the USB driver • Using the Virtual Ethernet Port • Using the Virtual Serial Port 6 The PinPoint X is equipped with a USB port which increases the methods by which you can send and receive data. The USB port can be set to work as either an Ethernet port or a virtual serial port. A driver installation is required to use the USB port in either mode. Note: It is recommended that you use a USB 2.
PAGE 55
Universal Serial Bus (USB) Installing the USB driver 1. Set the Port Type Virtual Ethernet port is the default setting for the USB port. If you want to install the virtual serial port, change the USB port configuration using the directions above. 2. Connect the PinPoint X to your computer’s USB port When you connect the PinPoint X for the first time to a USB port on your computer, Windows should detect a new device and prompt you to install the driver.
PAGE 56
Universal Serial Bus (USB) Figure 6-3: Hardware Wizard : Location options 3. Install the driver from a specific location a. Select and/or enter the location of the driver. · If the driver is on the CD and the CD is in your drive, you can just select Search removable media. · If you have installed AceManager or the Setup Wizard, the drivers have been conveniently copied to your hard drive. Enter C:\Program Files\Common Files\AirLink as the location to search.
PAGE 57
Universal Serial Bus (USB) c. Click Finish to complete the installation. The driver should be enabled without any need to reboot your computer. Figure 6-6: Hardware Wizard : Finish Note: If you are already connected to the modem with an Ethernet cable, when you complete the installation of the USB Ethernet driver, your computer will not use the USB connection initially. You may need to reboot your computer before you can use the USB port as an Ethernet connection to the modem. 4.
PAGE 58
Universal Serial Bus (USB) You can also verify the installation by looking in the Device Manager. a. Click on Start > Control Panel. b. Double‐click on the System icon. c. Select the Hardware tab and click the Device Manager button. Figure 6-8: System Properties d. Click on the + in front of Network Adapters. The newly installed driver, AirLink USB Ethernet/RNDIS, should be displayed.
PAGE 59
Universal Serial Bus (USB) Figure 6-9: Device Manager - Ethernet Virtual Serial You can verify the installation by looking in the Device Manager. a. Click on Start > Control Panel. b. Double‐click on the System icon. c. Select the Hardware tab and click the Device Manager button. Figure 6-10: System Properties d. Click on the + in front of Modems. Rev 3.0B Feb.
PAGE 60
Universal Serial Bus (USB) The newly installed driver, AirLink USB Serial Port, should be displayed. Tip: If the driver is displayed with a # and number behind the driver name (such as, AirLink USB Serial Port #2), it means more than one is installed on your computer, most likely for different USB port. More than one copy of the driver should not cause any problems since only the connected port and its driver would be active.
PAGE 61
Universal Serial Bus (USB) Figure 6-12: Device Manager : Driver menu b. Select the Advanced tab and click the Advanced Port Settings button. Figure 6-13: Driver Properties c. Rev 3.0B Feb.08 At the bottom of the screen, the current port used will be listed. Use the drop down menu to select an available COM port number if you need to change it.
PAGE 62
Universal Serial Bus (USB) Figure 6-14: Advanced Settings Using the Virtual Ethernet Port Once the driver is installed, you can use the USB port just like a standard Ethernet port. Using USB Ethernet with AceManager In AceManager, use the UDP or TCP connection and enter the IP address of the modem (192.168.13.31 by default) and the password (12345 by default). Figure 6-15: AceManager : TCP Using USB Ethernet with a Terminal Emulation Utility Configure your terminal application for telnet communication.
PAGE 63
Universal Serial Bus (USB) Figure 6-16: HyperTerminal : TCP c. Enter the modem password (12345 by default) when requested. Using the Virtual Serial Port Once the driver is installed, you can use the USB port just like a standard serial port. Using the USB virtual serial port with AceManager In AceManager, the USB virtual serial port connection will appear as a standard serial port. Use the PPP connection and select the COM#serial port of the USB connection.
PAGE 64
Universal Serial Bus (USB) Using the USB virtual serial port with a Terminal Emulation Utility a. Select the serial port of the USB connection when prompted for a COM port. b. Change the Bits per Second to 115200 (default), Data Bits to 8, Parity to None, Stop Bits to 1, and Flow Control to Hardware. c. Rev 3.0B Feb.08 You should also need to make sure your connection uses Auto Detect for the terminal emulation.
PAGE 65
7: Inputs, Relay Outputs, and Power Status • Capturing External Events • Power Modes and Information 7 The PinPoint X has special features for use in a mobile environment. The PinPoint X can be configured to monitor the inputs and respond to specific types of events. The PinPoint X can also be configured to change its power mode in order to conserve power. These features can be configured to your needs.
PAGE 66
PinPoint X HSDPA Digital Inputs Figure 7-2: Digital Input Contact Closure By measuring contact closures on switches, the digital inputs can report a simple open or closed state. Each of the four digital inputs can be wired to the two ground signals via a switch. When the switch is open, the input will read “OPEN”. When the switch is closed and the input is connected to ground, the input will read “CLOSED”. • When a door or other latch is opened or closed. • Counting pulses or other electronic events.
PAGE 67
Inputs, Relay Outputs, and Power Status Tip: The relays are only capable of switching small loads. If you need a stronger signal, such as to open a door lock, you can connect the PinPoint X’s relay to a stronger solenoid relay which has enough power to cause the desired effect. Connecting devices to the I/O Port Note: Before you install the PinPoint X in its final location, be sure to cover all exposed wiring.
PAGE 68
PinPoint X HSDPA Figure 7-4: I/O Wiring Harness, AirLink part number 120-140-1014 22 21 20 19 18 17 16 15 14 13 12 O/W Bl/Br O/Bl none G/Bl G/W none none V/W Bl/W V/Bl O/G Bl/G O/R none Y/Bl Y/W nonenone V/G Bl/R V/R 11 10 9 8 7 6 5 4 3 2 1 Figure 7-5: Color Corospondance to connection points Table 7-2: Wiring Color Corospondance 1. Violet/Red 12. Violet/Black 2. Black/Red 13. Black/White 3. Violet/Green 14. Violet/White 4. none 15. none 5. none 16. none 6.
PAGE 69
Inputs, Relay Outputs, and Power Status Digital Inputs Connect a wiring lead to a digital input (DIN) at 9, 11, 20, or 22, and the nearest ground at 8, 10, 19, or 21, as applicable. Caution: Never apply voltage to the Digital inputs. The inputs can only be switched open or closed to ground. Relay Outputs Connect the circuit leads to one of the two relay pairs at 6 and 7 or at 17 and 18.
PAGE 70
PinPoint X HSDPA Getting Immediate Reports Using RAP You can set up the PinPoint X to report immediately report the state of an input when it changes by using *PPFLUSHONEVT. You will also need *PPINPUTEVT, input event reports, enabled and a server configured for your RAP reports. These settings are in the PinPoint group in AceManager.
PAGE 71
Inputs, Relay Outputs, and Power Status Figure 7-9: AceManager : Low Power Wiring the PinPoint X for When the Standby Ignition Sense is enabled and the ignition sense connector is wired to your vehicle, the ignition sense will provide a link to the modem to enable it to enter a low‐power using standby mode. The white wire of the three wire connector should be used to connect to your ignition.
PAGE 72
PinPoint X HSDPA Figure 7-11: AceManager : Status - *POWERIN/*BOARDTEMP 59 20070914
PAGE 73
8: Data Communication and Host Modes • Basic Modes • Serial Modes • Data Communication 8 The PinPoint X plays the part of a HOST when a computer or another device is connected directly to its port and routes data to/from the connected device to the cellular network. Caution: The PinPoint X moves data from one port to the cellular network in a simple one-to-one routing. It does not employ a routing table or any complicated routing protocol.
PAGE 74
Data Communication and Host Modes • SLIP Mode: The PinPoint X uses SLIP to communicate with a device or computer connected to the serial or USB port. • UDP and UDP PAD: Any data received on the serial port is assembled into UDP packets and sent to the session’s associated IP address and Port (described later). Any responses received from the associated IP address and port destined for the Device Port are unwrapped and sent out the serial port.
PAGE 75
Data Communication and Host Modes Figure 8-1: AceManager : UDP - MD If the serial port of the PinPoint X is in any mode other than AT or PassThru, the AT command mode can be re‐entered by: • Deactivating DTR (if &D2 or Ignore DTR, S211, is not set). • Issuing the +++ escape sequence (if Disable AT Escape, DAE, is not set). • Resetting or Power cycling the modem. Note: DTR needs to be asserted (S211=1 or &D0) by the host before PPP Mode, SLIP Mode, UDP PAD Mode, or TCP PAD Mode can be entered.
PAGE 76
Data Communication and Host Modes If Quiet mode is off, the result code is affected as follows: For V=1 (Verbose mode), the textual result code is sur‐ rounded by a carriage return and new line. Any AT query response is also surrounded by a carriage return and new line. For V=0 (Terse mode), a numeric result code is output with a single trailing carriage return (no new line is output), while any AT query response is followed by a carriage return and new line (there is no preceding output).
PAGE 77
Data Communication and Host Modes You can configure a string of AT commands to be sent to the PinPoint X when it enters PassThru and other PassThru settings. Figure 8-2: AceManager : PassThru PassThru Mode allows only specific AT commands. Some ALEOS commands will be unavailable when the PinPoint X is in PassThru mode. The commands usable also depend heavily on the modem model number (found on the label on the top of the PinPoint X).
PAGE 78
Data Communication and Host Modes Figure 8-4: AceManager : Other - *TPORT, *TELNETTIMEOUT. Serial Modes PPP In PPP mode, the PinPoint X acts as a PPP server, providing an IP address, and DNS servers (if available) to the connected device or computer. PPP mode is entered from the AT mode by using any of the following commands: • AT\APPP • ATDT10.0.0.
PAGE 79
Data Communication and Host Modes Figure 8-5: AceManager : PPP/Ethernet Using a private IP insulates the PPP client from changes in IP addresses of the underlying network. The will perform basic NAT‐like address translation on all packets. If a public IP address is being used, any changes in the IP (as determined by the wireless network) will result in the PPP link to the host being disconnected, requiring the host to reinitiate it.
PAGE 80
Data Communication and Host Modes • Setting the Startup Mode Default (MD) to 3 (UDP) so that a UDP session is entered automatically when the modem registers onto the network. Serial data will be sent to the IP/port specified in S53.
PAGE 81
Data Communication and Host Modes Tip: It is best to ensure the idle time-outs for TCP and UDP are never 0 if you're going to be using auto-answer, or either PAD mode. In those circumstances, you will want the modem to close the socket if the connection goes idle for too long, particularly if the other side doesn’t normally close the connection. When the session is initiated by serial data, the new session will be established using the destination address specified in S53.
PAGE 82
Data Communication and Host Modes UDP Multicast Mode UDP Multicast mode results in any data received from the host serial port being sent to all the clients in the address list. The remote port number is taken from S53. To avoid flooding the network, the packets are sent to each client with a 20ms pause in between. The receipt of UDP packets works as in normal UDP mode (i.e. bound by the value S53 and/or AIP).
PAGE 83
Data Communication and Host Modes The TCP session will be terminated if no data is transmitted or received for the time interval specified in TCPT and TCPS. TCPT is the number of minutes (TCPS=0) or seconds (TCPS=1) used for this idle time‐out. Caution: TCPT should never be 0 when using the TCP mode. A broken TCP session can result in the modem being left with a TCP half-open connection that can only be terminated with a reset.
PAGE 84
Data Communication and Host Modes Data Communication Note: The PinPoint X forwards messages to and from the cellular network for only ONE device per port. The PinPoint X is a one-to-one gateway and does not have advanced routing features required to do one-tomany routing. The primary purpose of the PinPoint X is to forward data from a single device connected to one of the ports to the cellular network and, ultimately, under most circumstances, to the Internet in a one‐to‐one gateway configuration.
PAGE 85
Data Communication and Host Modes Figure 8-6: AceManager : PPP/Ethernet • *HOSTPRIVMODE ‐ Set to 1 to enable the explicit IP addresses. • *HOSTPRIVIP ‐ Set to the IP address you want the PinPoint X to give to your device. • *HOSTPEERIP ‐ Set to the IP address you want for the PinPoint X. • *HOSTNETMASK ‐ Set to the subnetmask, generally 255.255.255.0. Tip: If you are using Private Mode (*HOSTPRIVMODE=1), you will need to make sure that *HOSTPRIVIP and *HOSTPEERIP are on the same subnet.
PAGE 86
Data Communication and Host Modes as subnet masks, routers, etc.) to each computer or device without the need to set up each specifically or keep track of what addresses have already been used. In a default configuration, the PinPoint X acts as a DHCP host to any device connected to its ports, providing that device with an IP address which can be used to communicate on the Internet. In Public Mode, that will be the IP address assigned by the cellular network.
PAGE 87
Data Communication and Host Modes Configuring Keepalive In AceManager, the Keepalive settings are part of the Other group. Figure 8-7: AceManager : Other • *IPPING sets the interval, in minutes, you want Keepalive to test the network connection. To disable Keepalive, set *IPPING to 0 (default setting). Note: 15 minutes is the minimum time which can be set for Keepalive. If you set *IPPING for a value less than the minimum, the minimum value will be set.
PAGE 88
Data Communication and Host Modes *IPPING Rev 3.0B Feb.
PAGE 89
9: IP Manager • Understanding Domain Names • Using IP Manager with your PinPoint X • Understanding DNS 9 If you have a fleet of Sierra Wireless AirLink modems or even if you only have one, it can be difficult to keep track of the current IP addresses, especially if the addresses aren’t static but change every time the modems connect to Provider. If you need to connect to a modem, or the device behind it, it is so much easier when you have a domain name (car54.mydomain.com, where are you?).
PAGE 90
IP Manager • Dynamic IP addresses are granted only when your PinPoint X is connected and can change each time the modem reconnects to the network. • Static IP addresses are granted the same address every time your PinPoint X is connected and are not in use when your modem is not connected. Since many cellular providers, like wire‐based ISPs, do not offer static IP addresses or static address accounts cost a premium vs.
PAGE 91
IP Manager need to be registered with ICANN or any other registry. It is the responsibility of a domain to keep track of its own subs. car54.mydomain.com • .com is the TLD • mydomain is the domain (usually noted as mydomain.com since the domain is specific to the TLD) • car54 is the subdomain or server name associated with the device, computer, or modem registered with mydomain.com car54.mydomain.com.ca This would be the same as above, but with the addition of the country code.
PAGE 92
IP Manager Note: The fully qualified domain name of your PinPoint X will be a subdomain of the domain used by the IP Manager server. Using IP Manager with your PinPoint X To allow your Sierra Wireless AirLink modem to be addressed by name, the modem needs to have a minimum of three elements configured. You can also configure a second dynamic server as a backup, secondary, or alternate server. In AceManager, select Dynamic IP.
PAGE 93
IP Manager the IP address changes (example, if your PinPoint X is reset or is assigned a different IP address). • *IPMGRKEY1 and *IPMGRKEY2: User defined password key which is used instead of AirLink secret key when using an IP Manager server other than the one provided by Sierra Wireless. Restrictions for Modem Name For the Modem Name, you should use something which is unique but also easy to remember. Your company name or the intended function of the modem are recommended.
PAGE 94
IP Manager Note: The IP Manager service from Sierra Wireless is currently not a guaranteed service though every effort is made to keep it operational 24/7. • *DOMAIN : eairlink.com • *IPMANAGER1 : edns2.eairlink.com • *IPMANAGER2 : eairlink.com Tip: When using the IP Manager service offered by Sierra Wireless, since there are many modems using the service, it is even more imperative to have a unique name for your modem.
PAGE 95
IP Manager Figure 9-2: AceManager: DNS • *DNS1 and *DNS2 ‐ The primary and secondary DNS servers set by Provider when your PinPoint X gets its IP address. • *DNSUSER ‐ Set this, if desired, to an additional DNS server to query first before the primary or secondary (just as a hosts file is queried first on a computer). If *DNSUSER is set to 0.0.0.0, it will be ignored. • *DNSUPDATE ‐ This command sets how often you want DNS Updates to be requested.
PAGE 96
10: Global Positioning System (GPS) • Configuring the PinPoint X for GPS • RAP Configuration • NMEA Configuration • TAIP Emulation Configuration 10 The PinPoint X is equipped with a Global Positioning System receiver (GPS) to ascertain its position and track the movements of a vehicle or other devices which move. The PinPoint X relays the information of its location as well as other data for use with tracking applications.
PAGE 97
Global Positioning System (GPS) from the difference between local time and the time the satellite signals were sent (this distance is called psuedoorange). The locations of the satellites are decoded from their radio signals and a database internal to the receiver. This process yields the location of the receiver.
PAGE 98
Global Positioning System (GPS) Examples of tracking applications using RAP: • Air‐Trak • TrackStar • CompassCom • Zoll Data • HTE • Spillman • and others... National Marine Electronics Association (NMEA) National Marine Electronics Association (NMEA) is a protocol by which marine instruments and most GPS receivers can communicate with each other. NMEA defines the format of many different GPS message (sentence) types, which are intended for use by navigational equipment.
PAGE 99
Global Positioning System (GPS) • NAD83 • NAD27 Before you Configure GPS To decide what configuration you need for your PinPoint X, there are some fundamental considerations you should determine: • Protocol: What is the GPS protocol used by your tracking application and what type of reports will you need? • Datum: What is the datum supported by your tracking application? • Dynamic IP Address: Will you need DNS support to handle a dynamic IP address account? Configuring the PinPoint X for GPS This
PAGE 100
Global Positioning System (GPS) Tip: You can use a fully qualified domain name instead of an IP address for most configuration options calling for an IP address if your PinPoint X is configured to use DNS. Refer to the IP Manager chapter for how to configure DNS and how to allow your PinPoint X use a domain name even with a dynamic IP address account from AT&T.
PAGE 101
Global Positioning System (GPS) Local Host To set the PinPoint X to report to a local host, one directly connected to the serial port, configure the port to be used with S53 ‐ Destination Port. The local IP address will automatically be used for local reports. S53, in AceManager, is part of the Misc group. Figure 10-3: AceManager : Misc - S53 Port If you need to send reports to additional local ports, you can specify other ports with *PPLATSEXTRA.
PAGE 102
Global Positioning System (GPS) Figure 10-5: AceManager : PinPoint - *PPTCPPOLL Note: Some Internet providers (including cellular) block ports below 1024. Report Types There are several report types available. For remote reports, set *PPGPSR. For local reports, set *PPLATSR. Figure 10-6: AceManager : PinPoint - *PPGPRSR • 0 ‐ *MF, Legacy reports for use with ATS version 4 and older. • 11 ‐ Global Positioning System (GPS) data. • 12 ‐ GPS data with the UTC time and date.
PAGE 103
Global Positioning System (GPS) Sending Reports Automatically Remote You can configure the PinPoint X to send reports based on a time interval and on the movement of a vehicle (based on it’s position from one time to the next). Figure 10-7: AceManager : PinPoint - *PPTIME, *PPDIST, *PPTSV, *PPMINTIME • *PPTIME ‐ Location report sent every set time interval (seconds). • *PPDIST ‐ Location report sent only if the position is more than the set distance (x 100 meters).
PAGE 104
Global Positioning System (GPS) Figure 10-9: AceManager : PinPoint - #IG Store and Forward Store and Forward can provide seamless coverage even in areas with intermittent cellular coverage. If the PinPoint X leaves coverage or has very low signal (an RSSI of ‐105 or lower), it will store the GPS messages in memory. When the modem re‐enters cellular coverage, it will then forward the messages as configured.
PAGE 105
Global Positioning System (GPS) If the PinPoint X doesn’t receive acknowledgement for a “window”, the modem will PING the server with a message containing the sequence numbers of the first and last packets that haven’t been acknowledged. The PinPoint X will continue until the server acknowledges receipt. When the PinPoint X receives the acknowledgement, it will advance its “window” to the next group.
PAGE 106
Global Positioning System (GPS) Flush on Event If you have events enabled, with *PPFLUSHONEVT, you can configure the PinPoint X to flush the SnF buffer when an event occurs. This will immediately send all pending SnF messages to the host. This allows an event, such as a vehicle being powered on or a tow bar activated, to be immediately sent, so its cause can be acted on without delay.
PAGE 107
Global Positioning System (GPS) 12 ‐ GPS + Date ‐ GPS data with the UTC time and date 13 ‐ GPS + Date + RF ‐ GPS data with the UTC time and date and Radio Frequency information from the antenna. Figure 10-15: AceManager : PinPoint - *PPGPSR Tip: If your AVL host server uses a dynamic IP address or needs to change its IP address for any reason, you can use the RAP configuration command to change the value for *PPIP.
PAGE 108
Global Positioning System (GPS) b. Set the Local Report Type, using *PPLATSR, to your preferred RAP report type. Figure 10-17: AceManager : PinPoint - *PPLATSR 11 ‐ GPS ‐ Global Positioning System data 12 ‐ GPS + Date ‐ GPS data with the UTC time and date 13 ‐ GPS + Date + RF ‐ GPS data with the UTC time and date and Radio Frequency information from the antenna. c. Set Local Reporting Time Interval, using *PPLATS, to the number of seconds you want as an interval between reports being sent.
PAGE 109
Global Positioning System (GPS) Tip: If the PinPoint X is using a dynamic IP, *PPDEVID needs to be enabled. Odometer Data in Reports When the odometer report is enabled, the PinPoint X will calculate distance between reports based on GPS data. The modem’s odometer calculations can be included in the RAP message. Figure 10-20: AceManager : PinPoint - *PPODOM, *PPODOMVAL • *PPODOM enables the odometer reporting. • *PPODOMVAL is the current odometer reading in the PinPoint X.
PAGE 110
Global Positioning System (GPS) Support for a COM1000 is enable with the command *PPCOM1000=1 or *PPREPORTINPUTS=1. Once enabled, ALEOS will receive the reports from a properly configured COM1000 and add the state of the extra inputs to RAP packets sent to the RAP Host. Figure 10-22: AceManager : *PPCOM1000, *PPREPORTINPUTS If you are replacing an existing Pinpoint or PinPoint‐E in a vehicle with a COM1000, simply replace earlier modem with the with the PinPoint.
PAGE 111
Global Positioning System (GPS) NMEA Configuration Messages Over-The-Air (Remote) To configure the PinPoint X to send NMEA reports to a remote server, you will need to set 3 commands: *PPIP, *PPPORT, and *PPGPSR. a. Set *PPIP and *PPPORT to the IP address and port of the server to which you want the reports sent. Figure 10-24: AceManager : PinPoint - *PPIP/*PPPORT b. Set the GPS Report Type (*PPGPSR) to your preferred NMEA sentence format.
PAGE 112
Global Positioning System (GPS) Figure 10-26: AceManager : Misc - S53 Port b. Set the Local Report Type, *PPLATSR, to your preferred NMEA sentence format. Figure 10-27: AceManager : PinPoint - *PPLATSR • E0 ‐ NMEA GGA and VTG sentences. • E1 ‐ NMEA GGA, RMC, and VTG sentences. c. Set Local Reporting Time Interval, using *PPLATS, to the number of seconds you want as an interval between reports being sent.
PAGE 113
Global Positioning System (GPS) Figure 10-29: HyperTerminal : NMEA Streaming Persistent Streaming To have persistent streaming, allowing you to stream the data even after the modem is reset, configure *PGPS and set *PGPSR for NMEA. Figure 10-30: AceManager : PinPoint - *PGPS • 0 ‐ Disable NMEA streaming. • 1 ‐ Stream the NMEA strings out the serial port only. • 2 ‐ Stream the NMEA strings out the USB port only. • 3 ‐ Stream the NMEA strings out both the serial and the USB ports.
PAGE 114
Global Positioning System (GPS) TAIP Emulation Configuration The TAIP emulation functionality allows the PinPoint X to operate in a limited manner with clients which only under‐ stand the Trimble ASCII Interface Protocol (TAIP).This emulation is enabled by setting the GPS report format, directing the modem to listen for TAIP messages, and disabling RAP formatted messages to the same interface. TAIP ID TAIP messages can be configured to send the user specified identification number (ID).
PAGE 115
Global Positioning System (GPS) • SRM (Set Reporting Mode) allows the client to set the reporting mode configuration. The report mode configu‐ ration is not stored in non‐volatile memory and such should be resent upon a unit reset. This behavior emulates that specified in TAIP specifications. • QRM (Query Reporting Mode) reports the reporting mode configuration (returns an “RRM” message). • SID (Set ID) allows the client to set the TAIP ID (AT*PPTAIPID can also be used to set the TAIP ID).
PAGE 116
Global Positioning System (GPS) Note: Unlike standard TAIP which simply sends to the last client to request automatic reports, the remote reports are sent to the destination address (*PPIP) and destination port (*PPPORT). b. Set the GPS Report Type, *PPGPSR, to your preferred TAIP data format. Figure 10-35: AceManager : PinPoint - *PPGPRSR • F0 ‐ TAIP data (LN): latitude, longitude, altitude, the horizontal and vertical speed, and heading.
PAGE 117
Global Positioning System (GPS) Figure 10-36: AceManager : Misc - S53 Port b. Set *PPIP to the local IP address of the PinPoint X. The default IP address of the PinPoint X 192.168.13.31. Figure 10-37: AceManager : PinPoint - *PPIP c. Set Local Reporting Time Interval, using *PPLATS, to the number of seconds you want as an interval between reports being sent. Figure 10-38: AceManager : PinPoint - *PPLATS d. Set the GPS Report Type, *PPGPSR, to your preferred TAIP data format.
PAGE 118
Global Positioning System (GPS) Sending Unsolicited TAIP Messages over the Local Connection Standard TAIP requires a request before GPS reports are sent. The PinPoint X, however, can be configured to allow TAIP formatted messages to be sent over any UDP Port without request commands. This is useful for those applications which can listen for TAIP messages but cannot send UDP request packets. a. Set the S53 port to 1000. The local IP address will automatically be used. b.
PAGE 119
Global Positioning System (GPS) 1 ‐ Stream the TAIP strings out the serial port only. 2 ‐ Stream the TAIP strings out the USB port only. 3 ‐ Stream the TAIP strings out both the serial and the USB ports. 0 ‐ Neutralisez couler de TAIP. 1 ‐ Coulent les cordes de TAIP hors de la porte série seulement. 2 ‐ Coulent les cordes de TAIP hors du port d’USB seulement. 3 ‐ Coulent les cordes de TAIP hors de la porte série et du port d’USB.
PAGE 120
11: SNMP : Simple Network Management Protocol • SNMP Configuration • SNMP MIB Definition Sample 11 The Simple Network Management Protocol (SNMP) was designed to allow remote management and monitoring of a variety of devices from a central location. The SNMP management system is generally composed of agents (such as your PinPoint X, a router, a UPS, a web server, a file server, or other computer equipment) and a Network Management Station (NMS) which monitors all the agents on a specific network.
PAGE 121
SNMP : Simple Network Management Protocol SNMP Configuration To configure your PinPoint X to work as an SNMP agent, you can use either AceManager, or a terminal connection to configure the modem using AT commands. In AceManager, the SNMP commands are all part of the Other group under the Common group. There are only three commands to set for SNMP in the PinPoint X: the listening port, the security level, and the trap destination.
PAGE 122
SNMP : Simple Network Management Protocol User Name and Password The user name is ʹuserʹ. The user name cannot be changed. The PinPoint Xʹs password is used as the SNMP password (default is ʹ12345ʹ). Tip: The eight-character password requirement for SMNPv3 is not enforced by the PinPoint X Agent to allow the default password to function. Your SNMP administrator or MIS may require you to change to a more secure and/or longer password.
PAGE 123
SNMP : Simple Network Management Protocol Trap Destination *SNMPTRAPDEST needs to be set with the destination IP and port. If either are set to zero or empty, SNMP traps are disabled. Note: Traps are sent out according to the SNMP security level (i.e. if the security level is 2, traps will be authenticated and encrypted). Currently, the only trap supported is LinkUp. Community String The community string can be configured using *SNMPCOM‐ MUNITY. The default is “public”.
PAGE 124
SNMP : Simple Network Management Protocol electronicID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current ::= { general 3 } modemType OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current ::= { general 4 } aleosSWVer OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current ::= { general 5 } aleosHWVer OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current ::= { general 6 } modemSWVer OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS cu
PAGE 125
SNMP : Simple Network Management Protocol STATUS current ::= { common 2 } devicePort OBJECT-TYPE SYNTAX INTEGER(0..
PAGE 126
SNMP : Simple Network Management Protocol none(0), hardware(2), software(4) } MAX-ACCESS read-only STATUS current ::= { common 10 } -- STATUS -ipAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current ::= { status 1 } netState OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current ::= { status 2 } netChannel OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current ::= { status 3 } rssi OBJECT-TYPE SYNTAX INTEGER(-125..
PAGE 127
SNMP : Simple Network Management Protocol powerMode OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current ::= { status 8 } fixObtained OBJECT-TYPE SYNTAX INTEGER { no(0), yes(1) } MAX-ACCESS read-only STATUS current ::= { gps 1 } satelliteCount OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current ::= { gps 2 } latitude OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current ::= { gps 3 } longitude OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current :
PAGE 128
SNMP : Simple Network Management Protocol Object AT Command aleosHWVer I1 modemSWVer I2 modemHWVer I2 date *DATE? otaProgrammingEnable OPRG? devicePort *DPORT? netUID *NETUID? netPW *NETPW? requestPAP *HOSTPAP? destinationAddress S53 destinationPort S53 serialPortSettings S23 serialPortFlowControl \Q ipAddress *NETIP? netState *NETSTATE? netChannel *NETCHAN? rssi *NETRSSI? serialSent not applicable for Raven-E serialReceived not applicable for Raven-E hostMode *HOST
PAGE 129
A: Configuration Commands • • • • • • • A Info (information) Status Common Logging PinPoint (GPS) I/O Edge/HSDPA The configuration commands (AT commands) in this chapter are arranged according to their placement in AceManager. The commands available in AceManager will depend of the model number of your PinPoint X and, in some cases, the version of the ALEOS firmware installed. Note: Some commands can only be configured using a terminal emulation and typed AT commands.
PAGE 130
Configuration Commands Figure 1-1: AceManager : Info *DEVICEID? The 64‐bit device ID the modem uses to identify itself to the cellular network. *ETHMAC? The MAC address of the Ethernet port. *NETPHONE? The modemʹs phone number, if applicable or obtainable. &V View active profile, the contents of the active registers. Not displayed with AceManager. In Rev 3.0B Feb.08 • n=0 : Product name (for example, PinPoint X). • n=1 : The PinPoint X’s firmware (ALEOS) version, hardware ID, and copyright.
PAGE 131
Configuration Commands Information Displayed in AceManager without AT Commands Listed • Versions of ALEOS, internal hardware, boot, and MSCI: Versions of internally configured hardware and software. Status Most of the commands in the “Status” group have read‐only parameters and provide information about the modem. The Status Group has more fields that can be displayed on most screens. You can either resize your window or use the scroll bar on the side to display the remainder.
PAGE 132
Configuration Commands *NETIP? Note: If there is no current network IP address, 0.0.0.0 may be displayed. The current IP address of the modem reported by the internal module, generally obtained from AT&T. This is the address can contact the PinPoint X from the Internet. Tip: Use *NETALLOWZEROIP if you need to allow the display of an IP ending in a zero. *NETOP? The current cellular carrier from the modemʹs firmware version, for example, AT&T.
PAGE 133
Configuration Commands • Hardware Reset: The internal module is being reset. This is a temporary state. *POWERIN? The voltage input to the internal hardware. *POWERMODE? Displays the current power state/mode. Possible values returned are: • Initial: The modem is in the initial 5 minutes since power up, so power down event will be ignored. • On: Regular power on, a power down is not pending. • Low Cancellable: Power down is pending but still cancelable if the power down trigger goes away.
PAGE 134
Configuration Commands Figure 1-3: AceManager : Map link Figure 1-4: Map View AT Commands Requiring PassThru mode These commands are not displayed in AceManager. +CIMI Subscriber Identity Module ID. Common The groups under the heading Common encompass those commands that are common to most Sierra Wireless AirLink modems. Rev 3.0B Feb.
PAGE 135
Configuration Commands Misc (Miscellaneous) The commands of the “Misc” group are a variety of commands that don’t directly fit in other categories. Figure 1-5: AceManager : Misc +++ Note: +++ is not proceeded by AT nor does it require a carriage return (enter). There must be an idle time (set by S50) on the serial port before and after this command. AT Escape sequence. If the PinPoint X is in a data mode (any mode other than PassThru), this command causes the modem to re‐enter AT command mode.
PAGE 136
Configuration Commands • d.d.d.d= IP address to contact • ppppp= port to contact Examples: ATD - Dial (establish) default connection. ATDP192.168.13.31/2332 - Dial (establish) UDP session to 192.168.13.31, at port 2332. To end the connection, issue the +++ escape sequence or drop the DTR line (if Ignore DTR S211=0 or &D2). The default connection is set in S53. If the method, IP address, or port is omitted, the values from S53 are used.
PAGE 137
Configuration Commands OPRG=n Enables/disables over‐the‐air firmware upgrading of the PinPoint X. When Sierra Wireless releases a new version of ALEOS, you can upgrade your remote modems with OPRG enabled. • n=0 : Disables • n=1 : Enables S53=[method][d.d.d.d][/ppppp] Destination IP address, port, and method. These are used as defaults for the D (Dial) AT command. • method= P : UDP • method=T : TCP • method=N : Telnet • d.d.d.
PAGE 138
Configuration Commands • hh:mm:ss=time in 24‐hour notation *DPORT=n The modemʹs Device Port which the modem is listening on for inbound packets/data/polls. Can also be set with the command S110. • n=1‐65535 *HOSTPAP=n Use PAP to request the user login and password during PPP negotiation on the host connection. • n=0 : Disable PAP request (Default). • n=1 : Takes user login and password from Windows DUN connection and copies to *NETUID and *NETPW.
PAGE 139
Configuration Commands Caution: STATICIP does not set the IP address of the modem, it merely tells the modem which IP address to expect. If the expected IP address is not granted while registering on the cellular network, the modem will try to register on the network again until it receives that IP address.
PAGE 140
Configuration Commands Figure 1-7: AceManager : Serial En Toggle AT command echo mode. • n=0 : Echo Off. • n=1 : Echo On. Note: With more than one connection types (serial, Telnet, and USB) the echo command can be set differently on each interface. Qn The AT quiet‐mode setting. If quiet mode is set, there will be no responses to AT commands except for data queried. • n=0 : Off (Default). • n=1 : Quiet‐mode on. S3=n The standard end of line character used to indicate the end of an AT command.
PAGE 141
Configuration Commands S5=n This register sets the character recognized as a backspace during command entry. Cannot be configured in AceManager. • n=0‐127 (ASCII character number) S6=n This register denotes the wait time, in seconds, before a blind dial (no dial tone detection). Cannot be configured in AceManager. • n=2‐10 seconds S8=n Whenever a dial command contains the comma character, the contents of this register specify the pause time for each comma. Cannot be configured in AceManager.
PAGE 142
Configuration Commands Example: ATS23=19200,8N1 Sets modem to 19200, 8 databits, no parity, and 1 stop bit. Tip: Can also be set using &L=[speed],[databits] [parity][stop bits] S50=n Data forwarding idle time‐out. If set to 0, a forwarding time‐ out of 10ms is used. Used in UDP or TCP PAD mode. • n=tenths of a second S51=n PAD data forwarding character. ASCII code of character that will cause data to be forwarded. Used in UDP or TCP PAD mode. • n=0 : No forwarding character.
PAGE 143
Configuration Commands • n=1 : Assert DCD when in a data mode (UDP, TCP, PPP, or SLIP) (Default). • n=2 : Assert DCD when the modem has network coverage. &Dn Set DTR mode. • n=0 : Ignore DTR, same effect as HW DTR always asserted (same as S211=1). • n=2 : Use hardware DTR (same as S211=0). &Sn Set DSR mode. • n=0 : Always assert DSR (Default). • n=1 : Assert DSR when in a data mode (UDP, TCP, PPP, or SLIP) (Default). • n=2 : Assert DSR when the modem has network coverage.
PAGE 144
Configuration Commands RS232 voltage levels: Positive = Network coverage. Negative = No coverage. Tip: Flow control (AT\Q) will override this indication, so if you want to use CTS to indicate network coverage, flow control has to be off (AT\Q0). *NUMTOIP=n Convert 12 digit number to IP. • n=0 : Use as name. • n=1 : Use as IP address. *PPPNOCARRIER=n Provides a “No Carrier” message to a device connected to the serial port using PPP or CHAP when the cellular connection becomes unavailable.
PAGE 145
Configuration Commands • n=0 : Off (Default). • n=1 : On. • n=2 : Use Telnet server mode on TCP connections. • n=3 : With a Telnet connection, overrides the clientʹs default echo, allowing the server on the host port to perform the echo. CRLF sequences from the telnet client will also be edited to simply pass CRs to the server on the host port. S7=n Specifies the number of seconds to wait for a TCP connection to be established when dialing out. • n=seconds S60=n Telnet Client Echo Mode.
PAGE 146
Configuration Commands *ENQ=n Outputs an ENQ [0x05] after the TCP CONNECT delayed by the Delay Connect Response time (S221). • n=0 : Disabled (Default). • n=1 : Enable ENQ on CONNECT. UDP This group includes commands specific to UDP serial commu‐ nications. Figure 1-9: AceManager : UDP AIP=n Allow IP address. • n=0 : Allow only the IP address specified in S53 to connect when UDP auto answer is enabled (S82=2).
PAGE 147
Configuration Commands MDhh Default power‐up mode for the serial port: When the PinPoint X modem is power‐cycled, the serial port enters the mode specified by this command after 5 seconds. On startup, typing ATMD0 within 5 seconds changes the mode to normal (AT command) mode. See also S53 to set the port for UDP or TCP.
PAGE 148
Configuration Commands *UALL=n Accepts UDP packets from any IP address when a UDP session is active. If there is no UDP session active, an incoming UDP packet will be treated according to the UDP auto answer and AIP settings. • n=0 : No effect (Default). • n=1 : Accept UDP data from all IP addresses when in a UDP session. *UDPLAST=n Note: *UDPLAST does not change the S53 setting in NVRAM. If the modem is reset, the original S53 setting will be restored from NVRAM.
PAGE 149
Configuration Commands *DNSUPDATE=n Indicates whether the modem should send DNS updates to the DNS server specified by *DNSUSER. These updates are as per RFC2136. They are not secure and are recommended only for a private network. In a public network, the IP Logger services should be used instead. • n=0 : DNS updates disabled (Default). • n=1 : DNS updates enabled. *DNSUSER=d.d.d.d Sets a user‐provided DNS to query first when performing name resolutions in the modem. • d.d.d.
PAGE 150
Configuration Commands Tip: Only letters, numbers, hyphens, and periods can be used in a domain name. *IPMANAGERn=[name][IP address] Sets a domain name or IP address to send IP change notifica‐ tions to. Up to two independent IP Manager servers can be set, using either AT*IPMANAGER1 or AT*IPMANAGER2. Updates to a server can be disabled by setting that entry to nothing (for example, “AT*IPMANAGER1=”). • n=1 : First IP Manager server. • n=2 : Second IP Manager server.
PAGE 151
Configuration Commands Example: if *MODEMNAME=mymodem and *DOMAIN=eairlink.com, then the modemʹs fully qualified domain name is mymodem.eairlink.com. Automatically Generated Names: #I3 ‐ The ESN/IMEI will be used as the name. #CCID ‐ The CCID will be used as the name. #NETPHONE ‐ The phone number will be used as the name. Tip: Each modem using IP Manager needs a unique name. Two modems cannot be called “mymodem”. One could be “mymodem1” with the other as “mymodem”.
PAGE 152
Configuration Commands requests.n=0 : Disabled. The Raven X will not send out replies to DHCP requests. Tip: For PPPoE, set *DHCPSERVER=0. *HOSTAUTH=n Host Authentication Mode: Use PAP or CHAP to request the user login and password during PPP or CHAP negotiation on the host connection. The username and password set in *HOSTUID and *HOSTPW will be used. • n=0 : Disable PAP or CHAP request (Default). • n=1 : PAP and CHAP. • n=2 : CHAP Tip: For PPPoE, set *HOSTAUTH=1 or *HOSTAUTH=2. *HOSTNETMASK=n.n.
PAGE 153
Configuration Commands address, the cellular connection will be closed (since the IP address has changed) and has to be re‐initiated. (default). • n=1 : Private IP Mode: When the Host initiates a 1x connection, the host will be given the IP address specified in *HOSTPRIVIP. The modem will then perform 1 to 1 NAT‐like address translation, which shields the Host from network IP changes. *HOSTPW=string Host Password for PAP, CHAP, or PPPoE.
PAGE 154
Configuration Commands Note: It may take up to 30 seconds for the hardware module to respond after CONNECT is output. *CSX1=n PassThru Echo : Echo data to the host. • n=0 : Data will be passed to the host. • n=1 : PASSTHRU mode will echo all host received data and will not pass the data to the modem while the modem is not asserting DCD. Note: If the modem is asserting DCD, data will be passed from the host to the modem as it normally is when *CSX1=0.
PAGE 155
Configuration Commands SMS (Short Message Service) is another way to send messages via the cellular network. Most SMS commands require the modem to be in PassThru mode. Note: SMS may not be supported by your account with your cellular carrier. Figure 1-14: AceManager : SMTP *NETSMS2EMAIL=n Specify the SMS/E‐mail server number. This maybe necessary to send an SMS message to an email address. Cannot be used with AceManager. • n=SMS/E‐mail server number *SMTPADDR=[d.d.d.
PAGE 156
Configuration Commands *SMTPSEND=email[body] Sends an email to the address specified, followed by the body of the email message. The email message is terminated and sent by entering a . or Ctrl‐Z on an empty line. Cannot be configured with AceManager. • email=email address • body=message body *SMTPSTATUS? Returns the status of the last issued SMTP message (*SMTPSEND). If no status is available 0 is returned. Once read, the status is cleared out.
PAGE 157
Configuration Commands Other Figure 1-15: AceManager : Other DAE=n AT Escape Sequence detection. • n=0 : Enable • n=1 : Disable *DATZ=n Enables or disables reset on ATZ. • n=0 : Normal Reset (Default). • n=1 : Disable Reset on ATZ. *IPPING=n Set the period to ping (if no valid packets have been received) a specified address (*IPPINGADDR) to keep the modem alive (online).
PAGE 158
Configuration Commands *IPPINGADDR=[d.d.d.d][name] Set the IP address or valid internet domain name for the PinPoint X to ping to keep itself alive (online). *IPPING must to be set to a value other than 0 to enable pinging. • d.d.d.d=IP address • name=domain name *MSCIUPDADDR=name[/port] Modem Status Update Address ‐ where Name/Port is the domain name and port of the machine where the modem status updates will be sent. The status parameters of the PinPoint X are sent in an XML format.
PAGE 159
Configuration Commands *SNMPPORT=n This controls which port the SNMP Agent listens on. • n=0 : SNMP is disabled. • n=1‐65535 *SNMPSECLVL=n Selects the security level requirements for SNMP communica‐ tions. • n=0 : No security required. SNMPv2c and SNMPv3 communications are allowed. • n=1 : Authentication equivalent to “authNoPriv” setting in SNMPv3. SNMPv3 is required to do authentication, SNMPv2c transmissions will be silently discarded.
PAGE 160
Configuration Commands • n=minutes *TPORT=n Sets or queries the port used for the AT Telnet server. If 0 is specified, the AT Telnet server will be disabled. The default value is 2332. • n=0 : Disabled. • n=1‐65535 Tip: Many networks have the ports below 1024 blocked. It is recommended to use a higher numbered port. *TQUIT Disconnects the telnet session. Not available in AceManager.. Low Power The PinPoint X will put itself into a low power using mode when configured events occur.
PAGE 161
Configuration Commands one minute.In the first 5 minutes after PinPoint X powers up, power down events are ignored to give the user time to change configurations. SISE=n Standby Ignition Sense Enable: the PinPoint X will monitor the ignition sense on the power connector and enter the low power consumption stand‐by mode when the ignition is turned‐off. • n=0 : Disable • n=1 : Enable VLTG=n Set or query the voltage level at which the PinPoint X goes into low power mode.
PAGE 162
Configuration Commands Figure 1-17: AceManager : Friends FM=n Friends Mode ‐ Only allow specified IPs to access the PinPoint X modem. • n=0 : Disable Friends mode • n=1 : Enable Friends mode ‐ Only packets from friends will be accepted, packets from other IP addresses are ignored. Fn=[d.d.d.d] Friends mode IP address. • n=0‐9 Friends list index • d.d.d.d = IP address Using 255 in the IP address will allow any number. Example: 166.129.2.255 allows access by all IPs in the range 166.129.2.0‐166.129.
PAGE 163
Configuration Commands Figure 1-18: AceManager : Logging *DBGCOMMLVL=n Set the logging level for the host or module COM port. • n=0 : No logging • n=1 : Host COM Port • n=2 : Module COM Port *DBGDHCPLVL=n Enable or disable internal DHCP logging. • n=0 : No logging • n=1 : Log DHCP events. *DBGETHLVL=n Sets the logging level for the Ethernet port. • n=0 : No logging • n=1 : Log errors: invalid/corrupt packets, etc. • n=2 : Log the header of all received packets.
PAGE 164
Configuration Commands • n=1 : Log client events (default) • n=2 : Log server events • n=3 : Log client and Server events PinPoint (GPS) This group includes commands specific to GPS features and the PinPoint X Figure 1-19: AceManager : PinPoint GPSn Send NMEA GPS strings out serial link. ATGPS (no parameter) will cause the NMEA GGA, RMC, and VTG GPS strings to output to the serial port one time. Not available in AceManager.
PAGE 165
Configuration Commands #U Immediately issue GPS report to the ATS server IP and port. Not available in AceManager. *PGPS=n Send NMEA GPS strings out serial link. Similar to ATGPS except that the *PGPS value can be saved to NVRAM so that it will continue to operate after resets. • n=0 : Disabled • n=1 : Send NMEA GPS strings out serial link. • n=2 : Send NMEA GPS strings out the USB port. • n=3 : Send NMEA GPS strings out both the serial and the USB port.
PAGE 166
Configuration Commands *PPFLUSHONEVT=n Flushes store and forward buffer when an input event (DTR/ RTS) occurs. • n=0 : Disable • n=1 : Enable *PPGPSDATUM=n Specifies the GPS datum to use for position reports. For accurate results, this value should match the datum used by receiving mapping application. • n=0 : WGS84 • n=92 : NAD27 • n=115 : NAD83 *PPGPSSENTENCES=n Specifies the NMEA sentences to display in the NMEA GPS Report. • n=0‐65535 (hex) *PPGPSR=n GPS report type.
PAGE 167
Configuration Commands *PPIP=d.d.d.d IP address where GPS reports are sent (ATS Server IP). Also see *PPPORT. • d.d.d.d=IP address Example: AT*PPIP=192.100.100.100 *PPLATS=n Local ATS ‐ Causes GPS reports to also be sent out the serial or Ethernet link every n seconds, when there is a PPP connection to the serial host or a connection to the Ethernet port is estab‐ lished. • n=0 : Disable • n=1‐255 seconds Tip: Sends to the PPP peer IP S110 with the Destination Port number S53.
PAGE 168
Configuration Commands *PPMINTIME=n Specifies the minimum amount of time between reports generated due to either the time interval (*PPTIME) or the distance interval (*PPDIST). This is useful to limit network traffic and make more efficient use of bandwidth. This can be used in conjunction with store and forward. The minimum value which this setting can take depends on the policies of the carrier. • n=0 : Disabled • n=1‐65535 seconds *PPODOM=n Enable odometer reporting.
PAGE 169
Configuration Commands *PPSNF=n Store and Forward will cause GPS reports to be stored up if the PinPoint X goes out of network coverage. Once the vehicle is in coverage the GPS reports will be sent en masse to the server. • n=0 : Disabled • n=1 : Enabled (default) *PPSNFB=n Store and Forward Behavior. When *PPSNF=1, the type of Store and Forward behavior is defined by: • n=0 : Normal Store and Forward.
PAGE 170
Configuration Commands • n=0 : Disabled • n=1‐65535 (default 9494) *PPTIME=n GPS Report Time Interval. See also *PPMINTIME, *PPTSV, +CTA. • Note: Your cellular carrier may impose a minimum transmit time. n=seconds (1 ‐ 65535) Caution: A report time of less than 30 seconds can possibly keep an RF link up continuously. This will eventually cause the PinPoint X to overheat and shutdown. An RF resource may continue be tied up to transfer small amounts of data.
PAGE 171
Configuration Commands Figure 1-20: AceManager : I/O *ANALOGINn? Query individual analog inputs. The analog inputs report the voltage in volts. • n=1‐4 Input number *DIGITALINn? Query individual digital inputs. The digital inputs report either a 0 (open) or 1 (closed). • n=1‐4 Input number *IOSTATE=n,s Query the full set of digital inputs, analog inputs, and relay outputs, or set the relay outputs.
PAGE 172
Configuration Commands • n=1‐2 Input number • s=OPEN or CLOSED Edge/HSDPA This group includes commands specific to HSDPA, EDGE and GPRS. If you are not connecting to a modem which uses HSDPA, EDGE, or GPRS, you will not see this group in the menu. Figure 1-21: AceManager : EDGE/HSDPA *NETAPN=apn Easy entry of the APN. If left blank, the modem will attempt to use the default subscriber value as defined by the account. • apn=access point name +CGQMIN Minimum Acceptable Quality of Service Profile.
PAGE 173
Configuration Commands Rev 3.0B Feb.
PAGE 174
B: PPP over Ethernet (PPPoE) • Configuring the PinPoint X for PPPoE • Configuring a PPPoE Connection in Windows • Connecting to the Internet with PPPoE B PPPoE (Point‐to‐Point Protocol over Ethernet) allows a point‐ to‐point connection while using Ethernet or the USB virtual Ethernet.
PAGE 175
PPP over Ethernet (PPPoE) 1. Configure your PinPoint X to support PPPoE a. Connect your PinPoint X directly to your computer and start AceManager. b. From the groups on the left, select PPP/Ethernet under Common. Figure 2-1: AceManager : PPP/Ethernet c. Change *HOSTAUTH to 2. d. Enter a user name for *HOSTUID for the PPPoE connection. e. Enter a password for *HOSTPW for the PPPoE to connection. f.
PAGE 176
PPP over Ethernet (PPPoE) b. Enter a name for *MODEMNAME, such as PinPoint X or the ESN. Figure 2-2: AceManager : Dynamic IP Tip: The name you choose will not affect the connection but may need to be configured in PPPoE settings for the router, device or computer you will be connecting to your PinPoint X. 3. Write the configured settings to your PinPoint X a. Click the Write button on the tool bar of AceManager and wait for the message “Write Successful” to appear in the status bar.
PAGE 177
PPP over Ethernet (PPPoE) Figure 2-4: Windows : Start menu b. Select Create a New Connection under Network Tasks in the menu area on the left. Select Next to start installing and configuring the PPPoE connection. Figure 2-5: Windows : Network Connections c. Click Next on the opening screen to begin creating a PPPoE connection. d. Next. Rev 3.0B Feb.
PAGE 178
PPP over Ethernet (PPPoE) Figure 2-6: New Connection Wizard e. Select Connect to the Internet. f. Select Next. Figure 2-7: New Connection: Type g. Select Set up my connection manually. h. Select Next. Figure 2-8: New Connection: How do you want to connect? Rev 3.0B Feb.
PAGE 179
PPP over Ethernet (PPPoE) i. Select Connect using a broadband connection. j. Select Next. Figure 2-9: New Connection : Connect using broadband k. Type in a name for the connection, such as Sierra Wireless AirLink Modem. l. Select Next. Figure 2-10: New Connection: Connection Name Tip: The name provided here will not effect the connection in any way. It is only a label for the icon.
PAGE 180
PPP over Ethernet (PPPoE) Same *HOSTUID as configured earlier Same *HOSTPW as configured earlier Figure 2-11: New Connection: Connection Information Caution: If you have a LAN connection to the Internet and select Make this the default Internet Connection for the PPPoE configuration, you will not be able to use the LAN to connect to the Internet and may also affect the network connection on your computer to the rest of the LAN.
PAGE 181
PPP over Ethernet (PPPoE) 2. Configure the PPPoE connection After you complete the New Connection Wizard, there are a few more things you will want to configure in the connection. a. Select Properties. Figure 2-13: PPPoE Connection b. Optional: On the General tab, if you gave the modem a name with *MODEMNAME above, you can type in that name as the Service Name. Same as *MODEMNAME configured earlier Figure 2-14: PPPoE Connection : Service Name c. Select Networking. d. Select Settings. Rev 3.0B Feb.
PAGE 182
PPP over Ethernet (PPPoE) Figure 2-15: PPPoE : Networking e. Remove the checks from all three PPP settings. f. Select OK. Figure 2-16: PPP Settings Tip: You may want to check the Options tab and change the settings for applications you might be using. The default options are generally applicable for most uses. Caution: Unless specifically directed to do so by Support or your network administrator, you do not need to make any changes to the options on the Security tab. g.
PAGE 183
PPP over Ethernet (PPPoE) Connecting to the Internet with PPPoE Now the PPPoE connection can be run and a data connection can be established. a. Connect your computer and the modem to the same local network using a hub or a switch. Note: It is not recommended to connect your computer directly to the modem without a hub or switch. b. Start the PPPoE by Start > Connect To > Sierra Wireless AirLink Modem (or whatever you named the connection).
PAGE 184
C: Windows Dial-up Networking (DUN) • Installing a modem driver for PinPoint X • Creating a Dial-Up Networking (PPP) Connection • Connecting to the Internet Using DUN C Dial‐up Networking (DUN) allows a computer or other device to use the serial port or USB virtual serial port on your PinPoint X to connect to the Internet or private network using PPP just like an analog modem using a standard phone line.
PAGE 185
Windows Dial-up Networking (DUN) Figure 3-1: Phone and Modem Options b. Select the Modems tab. Figure 3-2: Phone and Modem Options: Modems c. Rev 3.0B Feb.08 Select Add.
PAGE 186
Windows Dial-up Networking (DUN) Figure 3-3: Add Hardware Wizard d. Check Don’t detect my modem; I will select it from a list. e. Select Next. Figure 3-4: Add Hardware Wizard: Install New Modem f. Select (Standard Modem Types) from the Manufacturers column. g. Select Standard 33600 bps Modem from the Models column. Rev 3.0B Feb.
PAGE 187
Windows Dial-up Networking (DUN) Tip: If you have the speed for your modem configured as something other than the default, use the Standard Modem that matches the speed you configured. h. Select Next. Figure 3-5: Add Hardware Wizard: Select Ports i. Check Selected Ports j. Select the COM port the modem is connected to (commonly COM1). k. Select Next. Figure 3-6: Add Hardware Wizard: Finish l. Rev 3.0B Feb.08 Once the modem driver is installed, select Finish.
PAGE 188
Windows Dial-up Networking (DUN) 3. Configure the driver. When you return to the Phone and Modem Options window, you should see the newly installed modem “attached to” the correct COM port. Figure 3-7: Phone and Modem Options: Modems a. Highlight the modem and select Properties. Figure 3-8: Modem Properties Rev 3.0B Feb.
PAGE 189
Windows Dial-up Networking (DUN) b. Select the Modem tab. Figure 3-9: Modem Properties: Modem c. Maximum Port Speed should be set to 115200 (default). d. Select OK to exit. e. Select OK again to exit out of the Phone and Modem Options. Creating a Dial-Up Networking (PPP) Connection Once you have the driver for the modem installed on your computer, you can set up and configure Dial Up Networking (DUN) to use the modem as your connection to the Internet using PPP.
PAGE 190
Windows Dial-up Networking (DUN) Caution: If you have an existing LAN connection, installing DUN for the modem may interfere with the LAN connection. It's recommended to disconnect your LAN connection before using a PPP connection with your PinPoint X. Once the DUN connection is initiated, by default, it will take over as the “default route” for network communication and specifically for Internet access.
PAGE 191
Windows Dial-up Networking (DUN) b. Select Create a New Connection under Network Tasks in the menu area on the left. Figure 3-11: Create New Connection c. Select Next to start installing and configuring the DUN connection. Figure 3-12: New Connection Wizard d. Select Connect to the Internet. e. Select Next. Rev 3.0B Feb.
PAGE 192
Windows Dial-up Networking (DUN) Figure 3-13: New Connection: Type f. Select Set up my connection manually. g. Select Next. Figure 3-14: New Connection: How do you want to connect? h. Select Connect using a dial‐up modem. i. Select Next. Figure 3-15: New Connection: Connect using... j. Optional: If you have multiple modems installed on your computer, you may be prompted to select the modem to be used. If you only have one modem installed, this option will be omitted. k.
PAGE 193
Windows Dial-up Networking (DUN) Figure 3-16: New Connection: Select Modem m. Type in a name for the connection, such as Sierra Wireless AirLink Modem. n. Select Next. Figure 3-17: New Connection: Connection Name Tip: The name provided here will not effect the connection in any way. It is only a label for the icon. It can be the name of your wireless service provider (Provider), your modem (PinPoint X), or any other designation for the connection. o.
PAGE 194
Windows Dial-up Networking (DUN) Figure 3-19: New Connection: Permissions Generally the modem takes care of the Account Information, User name and Password, for the connection, so you can leave the fields blank (unless otherwise instructed by Support). s. If you want to allow others to use the same login for the modem, select Use this account name and password.... t. Select Next.
PAGE 195
Windows Dial-up Networking (DUN) Figure 3-21: New Connection: Finish 2. Configure the DUN connection After you complete the New Connection Wizard, there are a few more things you will want to configure in the connection. a. Select Properties. Figure 3-22: DUN Connection b. Uncheck Use dialing rules. Rev 3.0B Feb.
PAGE 196
Windows Dial-up Networking (DUN) c. Check Show icon...when connected. d. Select Configure, below the Connect using line. Figure 3-23: DUN Properties e. Select 115200 as the Maximum speed. f. Check Enable hardware flow control. g. Do not check any other option. h. Select OK. Rev 3.0B Feb.
PAGE 197
Windows Dial-up Networking (DUN) Figure 3-24: Modem Configuration i. Back at the main properties screen, select the Networking tab. Figure 3-25: Networking j. Select Settings. k. Remove the checks from all three PPP settings. l. Rev 3.0B Feb.08 Select OK.
PAGE 198
Windows Dial-up Networking (DUN) Figure 3-26: PPP Settings m. Select (highlight) Internet Protocol (TCP/IP) and then select Properties. Tip: For most configurations, you will be obtaining the IP address and the DNS server address automatically. n. Select Advanced. Figure 3-27: TCP/IP Properties o. Uncheck Use IP header compression. p. Check Use default gateway on remote network. q. Select OK. Rev 3.0B Feb.
PAGE 199
Windows Dial-up Networking (DUN) Figure 3-28: Advanced TCP/IP Tip: You may want to check the Options tab and change the settings for applications you might be using. The default options are generally applicable for most uses. Caution: Unless specifically directed to do so by Support or your network administrator, you do not need to make any changes to the options on the Security tab. r. Select OK until you return to the Connect window.
PAGE 200
Windows Dial-up Networking (DUN) 2. Enable the Connection. Figure 3-29: AceView: Menu a. Right‐click on the AceView window to open the menu. b. Select Connection Settings. Figure 3-30: AceView: Connection Settings c. Select Auto Start in the DUN section. d. Select Maintain Persistent Connection. When checked, AceView will continually check the DUN connection to ensure it is not down. If so, AceView will attempt to connect again.
PAGE 201
Windows Dial-up Networking (DUN) 1. Start the DUN session. Start > Connect To > Sierra Wireless Airlink Modem If you named the connection differently, use the name of the PPP connection you made earlier. Figure 3-31: DUN Connection Tip: Generally you will not need to enter a Username or Password. If you do need to enter either, you can enter these parameters beforehand using *NETUID and *NETPW. 2. Select Dial to connect to the modem and the cellular network.
PAGE 202
Windows Dial-up Networking (DUN) Caution: For DUN connections on a Windows Mobility or other nonpersonal computer, the DNS settings may not be configured with the DUN connection. You may need to go into the network settings and add DNS servers manually. Rev 3.0B Feb.
PAGE 203