User Manual

ManualsBrandsSiglent Technologies ManualsElectrical Testing200 mhz Digital Oscilloscope 2 Channels, Grey

221

222

223

224

225

226

227

228

229

230

Table Of Contents

Copyright and Declaration
Safety Information
- General Safety Summary
- Safety Terms and Symbols
- Measurement Category
- Working Environment
- Ventilation Requirement
- General Care and Cleaning
L'information de sûreté
- Résumé général de sûreté
- Limites et symboles de sûreté
- Catégorie de mesure
- Environnement de fonctionnement
- Condition de ventilation
- Soin général et nettoyage
Document Overview
Quick Start
- General Inspection
- Appearance and Dimensions
- Prepare for Using
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- Help
- User Interface
- Security Lock
Vertical System
- Enable the Channel
- Adjust Scale
- Vertical Position
- Coupling
- Bandwidth Limit
- Probe
- Input Impedance
- Unit
- Deskew
- Invert
- Trace Visible/Hidden
Horizontal System
- Horizontal Scale
- Trigger Delay
- Roll Mode
- Zoom Mode
Sample System
- Run Control
- Overview
- Memory Depth
- Sampling Mode
- Interpolation Method
- Acquisition Mode
- Horizontal Format
- Sequence Mode
Trigger
- Trigger Source
- Trigger Mode
- Trigger Level
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
Serial Trigger and Decode
- I2C Trigger and Serial Decode
- SPI Trigger and Serial Decode
- UART Trigger and Serial Decode
- CAN Trigger and Serial Decode
- LIN Trigger and Serial Decode
Reference Waveform
- Save REF Waveform to Internal Memory
- Display REF Waveform
- Adjust REF Waveform
- Clear REF Waveform
Math
- Units for Math Waveforms
- Math Operators
Cursors
- X Cursors
- Y Cursors
- Make Cursor Measurements
Measure
- Type of Measurement
- Automatic Measurement
- All Measurement
- Gate Measurement
- Clear Measurement
Display
- Display Type
- Color Display
- Persistence
- Clear Display
- Grid Type
- Intensity
- Grid Brightness
- Transparence
Save and Recall
- Save Type
- Internal Save and Recall
- External save and recall
- Disk Management
Digital Channels(Option)
- Connect the Digital Probes
- Acquire Digital Waveform
- Digital Channels Height
- Digital Channels Position
- Single Digital Channel
- All Digital Channels
- Logic Threshold
- Digital Bus
- Deskew
- System Setting
- Remove Device
System Setting
- View System Status
- Do Self Cal
- Quick-Cal
- Sound
- Language
- Pass/Fail Test
  - Set and Perform Pass/Fail Test
  - Save and Recall Test Mask
- Arbitrary Waveform Generator(Option)
- IO Set
- Web Server
- Update Firmware and Configuration
- Do Self-Test
- Screen Saver
- Reference Position
- Power On Line
- Option Management
Bode Plot II
- Perform Bode Plot
- Setting
- Example
  - Simple Sweep Operation
  - Vari-level Sweep Operation
Search
- Setting
- Results
Navigate
- Time Navigate
- History Frame Navigate
- Search Event Navigate
History
Factory Setup
Troubleshooting

SDS1000X-E User Manual

200

WWW.SIGLENT.COM

Figure 141 Set Vari-level Parameters Menu

10. The

Set Sweep

and

Set Stimulus

in Vari-level editor are similar to that in the Simple

sweep mode, but they are independently configured and do not affect each other.

These options in Vari-level mode do not have frequency and amplitude input because

they are specified in the spreadsheet. Press

Set Sweep

and then set Mode to

“

Decade

”, and set Points/dec to 20. The

Set Stimulus

remains default setting.

Figure 142 Set Sweep Parameters Menu

11. Return to Configure menu and press

Set Channel

. Set

DUT Input

to “

CH1

” and

DUT

Output 1

to “

CH2

”, and

Channel Gain

to “

Auto

”.

12. Configuration was done. Return to the root menu and press

Run

and wait for the

sweep to complete.