SDS1000X-E Series Super Phosphor Oscilloscope Quick Start
Copyright Information SIGLENT TECHNOLOGIES CO., LTD. All Rights Reserved. Declaration SIGLENT products are protected by patent law in and outside of P.R.C. SIGLENT reserves the right to modify or change parts of or all the specifications or pricing policies at company’s sole decision. Information in this publication replaces all previously corresponding material. Any way of copying, extracting or translating the contents of this manual is not allowed without the permission of SIGLENT.
General Safety Summary Carefully read the following safety precautions to avoid any personal injury or damage to the instrument and any products connected to it. To avoid potential hazards, please use the instrument as specified. Use Proper Power Cord Only the power cord designed for the instrument and authorized by local country could be used. Ground the Instrument The instrument is grounded through the protective earth conductor of the power cord.
Safety Terms and Symbols General Care and Cleaning Terms on the product. These terms may appear on the product: Care Indicates direct injuries or hazards that may happen. DANGER WARNING Indicates potential injuries or hazards that may happen. CAUTION Indicates potential damages to the instrument or other property that may happen. Do not store or leave the instrument in direct sunshine for long periods of time.
Contents Copyright Information................................................................................................................................................ General Safety Summary............................................................................................................................................. Quick start.............................................................................................................................................................
Quick start General Inspection 1. Inspect the shipping container Keep the damaged shipping container or cushioning material until the contents of the shipment have been completely checked and the instrument has passed both electrical and mechanical tests. The consigner or carrier will be responsible for damages to the instrument resulting from shipment. SIGLENT would not provide free maintenance or replacement if the instrument has been damaged in shipment. 2.
Quick start Adjust the Supporting Legs Connect to AC Power Supply Adjust the supporting legs properly to use them as stands to tilt the oscilloscope upwards for stable placement as well as easier operation and observation of the instrument. The oscilloscope accept 100-240V, 50/60/440Hz AC power supply. Please use the power cord provided as accessories to connect the instrument to the power source as shown in the figure below.
Quick start Power-on Inspection When the scope is energized, turn on the power switch at the lower left corner on the front panel. During the start-up process, the instrument performs a series of self-test items and you can hear the sound of relay switching. After the self-test completed, the User Interface displays immediately. Connect the Probe SIGLENT provides passive probe for the SDS1000X-E series oscilloscope. Please refer to corresponding Probe User Manual for detailed technical information.
Quick start Probe Compensation You should properly compensate the probe at first use of it. Non-compensated or inadequate compensated probe may cause inaccurate measurement. The following steps are about probe compensation: 1. Perform step 1, 2 , 3 and 4 of “Functional Inspection”. 2. Check the displayed waveforms and compare them with the following figure. Under Compensated Compensated Correctly Over Compensated 3.
The Front Panel 4 3 2 5 1 7 6 8 12 13 14 1.User Interface 2.Universal Knob 3.Function Menus 4.Run/Stop 5.Auto Setup SDS1000X-E Series Digital Oscilloscope -6 10 11 6.Trigger Control 7.Horizontal Control 8.Channel Vertical Control 9.Probe Compensation 10.Analog Channel Inputs 9 11.USB Host 12.Function Menu Softkeys 13.Menu On/Off 14.
The Rear Panel 1. Handle Pull up the handle vertically for easy carrying; press it down if you do not need the handle. 1 2.Safety Lock Hole You could lock the instrument in a fixed location using a security lock (please buy it yourself ) via the lock hole 3. LAN Interface 3 2 5 4 The instrument can be connected to network via this interface to perform remote control 4.
Front Panel Overview Horizontal Control Quickly enter into the Roll mode. The timebase range is from 50 ms/div to 100 s/div. Horizontal POSITION Sets the horizontal location of the trigger event on the display. The waveform will move left or right when you turn the knob. Meanwhile, the Delay value will increase or decrease as the waveform moves. Press down the knob to reset the trigger delay to zero.
Interval Trigger Runt Trigger The time interval from the rising edge (or falling edge) of input signal passes through the trigger level to the next rising edge(or falling edge) passes through the trigger level and the currently set time satisfy the Limit Range ( ＜ =, ＞ = , [ --.--], --] [--) selected Runt trigger includes positive runt trigger and negative runt trigger.
Pattern Trigger IIC Trigger Identify a trigger condition by looking for a specified pattern. This pattern is a logical combination (AND/OR/NAND/NOR) of the two channels. Each channel can be set a value among High, Low or Invalid. After setting the serial 1 or 2 to IIC type in trigger menu, you can use universal knob to set to trigger on start/stop condition, restart, no ack,EEPROM, or on the read/write frame with specific device address and data value.
SPI Trigger After setting the serial trigger to SPI type in trigger menu, you can select to trigger on MISO data or MOSI data. The data length are variable to set from 4 to 96. UART/RS232 Trigger After setting the serial trigger to UART/RS232 type in trigger menu, you can select to trigger on start , stop, checksum error or data. The data width are variable to set from 5 to 8bits.
Vertical Control Vertical Scale: Set the vertical scale of current waveform. Turn clockwise to decrease the scale and while turn anticlockwise to increase it. During the modification, the ‘amplitude’ of the waveform will enlarge or reduce and the scale message at the right side of the screen will also change. Press down the knob to quickly switch the vertical scale adjustment modes between “Coarse” and “Fine”. Analog input channels.
Universal Knob Function Menus Adjust Waveform Intensity/ Graticule/ Transparence You can press → Intensity and use the knob to adjust waveform intensity (0% ~ 100%). To adjust graticule (0% ~ 100%) or transparency(20% ~ 80%) ,please operate in the same way as waveform intensity. Universal Knob In menu operation, when the light below the knob is lit, you could turn the knob to select between submenus under the current menu and press it down Press the button to open the cursor function.
Press the button to enter the history mode. In history mode, it can record most 80000 frame waves This button is a shortcut key for clear function. When the measurement statistics is ON, press the button to clear the count and recount it. When persist is enabled, press the button to clear persist Press the button to enter the measurement setting menu. You could set measurement type, statistic function, all measure and gate measure. You can select as many as four parameters.
User Interface 1. Product Logo SIGLENT is the registered trademark of our company. 1 3 4 5 6 7 2. Channel Label/Waveform 8 Different channels are marked by different colors and the color of the waveform complies with the color of the channel. 9 3. Working state Available states include Arm, Ready, Trig’d, Stop, Auto. 10 4. Horizontal Time Base Represent the time of each grid on the horizontal axis of the 11 2 screen.
6. Trigger position Display the trigger position of the waveform on the screen. 7. Frequency Counter Display the firmware frequency of current waveform. 8. Sample Rate/Memory Depth Display the current sample rate and memory depth of the oscilloscope. Use horizontal SCALE knob to modify the parameter. 9. Trigger Setting Trigger Source Display the trigger source currently selected.
Using Security Lock If needed, you could use the security lock (please buy it yourself) to lock the instrument in a fixed location. The method: align the clock with the clock hole and plug it into the lock hole vertically, turn the key clockwise to lock the instrument and then pull the key out.
Trouble shooting The general failures and consequential solutions are listed below. When you find them, please deal with them in the following corresponding ways. If the problem proves to be unsolvable, please contact SIGLENT as soon as possible. 1. The screen remains dark after power on: (1) Check if the power is correctly connected. (2) Check if the power switch is faulted. (3) Check whether the fuse is burned out.
Trouble shooting 5. No display after pressing : Check whether the trigger Mode is “Normal” or “Single”, and if the trigger level exceeds the waveform range. If yes, set the trigger level to the middle or change the trigger Mode to “Auto”. Note: press “Auto Scale” could automatically replace the above setting. 6.The waveform displays like ladder: (1) The horizontal time base may be too low, you can increase it to improve the horizontal resolution so as to make a good waveform displaying.
www.siglent.
