UZB3 Z-Wave USB Adapter 1 1 UZB3 Model: UZB3-U UZB3-E Z-Wave USB Stick User’s Manual All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2014 Sigma Designs, Inc.
UZB3 Z-Wave USB Adapter 1 1 CONTENTS 1. INTRODUCTION ..........................................................................................................................3 2. SPECIFICATIONS..........................................................................................................................4 3. PC CONTROLLER APPLICATION SOFTWER INSTALLATION .............................................................6 4.1 Installation .......................................................
UZB3 Z-Wave USB Adapter 1 1 1. INTRODUCTION UZB, Z-Wave USB Stick and bundled application software (PC Controller) enables you to control a range of Z-Wave enabled devices through your PC or Notebook. Z-wave is an established short range interoperable two-way RF mesh network technology. Refer to http://www.z-wave.com/home for detail of the technology. Refer to http://products.z-wavealliance.org/ for various Z-Wave certified ready products. Refer to http://www.z-wavealliance.org for Z-Wave Alliances.
UZB3 Z-Wave USB Adapter 1 1 2. SPECIFICATIONS Z-Wave & RF Specification Z-Wave wireless transceiver comprises a 3-channel 1GHz ISM FSK/GFSK narrowband radios. Table 1. UZB3 General Specifications Region US EU Product UZB3 Product Description Model Part Number JAPAN Z-Wave USB Adapter UZB3-U UZB3-E UZB-H ACC-UZB3-U ACC-UZB3-E ACC-UZB3-H Manufacturer Sigma Designs Z-Wave Chip SD3503 Z-Wave Library Serial API Version 4.
UZB3 Z-Wave USB Adapter 1 1 Table 2. Z-Wave RF properties (US) Data rate 9.6kbps 40kbps 100kbps Frequency 908.42 MHz 908.40 MHz 916 MHz Modulation Frequency Shift Keying (FSK) Frequency Shift Keying (FSK) Gaussian Frequency Shift Keying (GFSK) fC±20kHz fC±20kHz fC±29.
UZB3 Z-Wave USB Adapter 1 1 3. PC CONTROLLER APPLICATION SOFTWER INSTALLATION 4.1 Installation 1. Exit all programs. 2. Run the installation file of the Z-Wave PC Controller application. Figure 1. Welcome page of Z-Wave PC Controller installation 3. Select the installation folder and who should be able to use the Z-Wave PC Controller application. Please note, that it is not recommended to move the Z-Wave PC Controller application manually after it has been installed into the above specified folder.
UZB3 Z-Wave USB Adapter 1 1 Figure 2. Installation folder 4. Installation confirmation appears. Click Next again to confirm and start the installation. Figure 3. Confirmation page of Z-Wave PC Controller installation All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2014 Sigma Designs, Inc.
UZB3 Z-Wave USB Adapter 1 1 5. The actual installation procedure will pass with progress indicator and final confirmation appears. 6. Click Close to complete the installation. Figure 4. Installation complete All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2014 Sigma Designs, Inc.
UZB3 Z-Wave USB Adapter 1 1 4.2 Start the Z-Wave PC Controller application You can start the Z-Wave PC Controller using the Start menu. To open the Start menu, click the Start button in the lower-left corner of your screen. Or, press the Windows logo key on your keyboard. The Start menu appears. To open Z-Wave PC Controller, click its icon shown in the left pane of the Start menu that displays the most frequently used programs list.
UZB3 Z-Wave USB Adapter 1 1 4.3 Remove Z-Wave PC Controller application Software You can uninstall Z-Wave PC Controller from your computer if you no longer use it. 1. Open Add or Remove Programs in Control Panel. To do it, click Start, then click Control Panel (in Classical View – click Start, then point to Settings, and click Control Panel), and then double-click Add or Remove Programs. 2. Click the program in the list and then click the Remove button.
UZB3 Z-Wave USB Adapter 1 1 4.4 User Interface The PC Based Controller application Main window (See Figure 3) is divided into the following views: • • • • • • Title bar Menu bar Node Controller Command Class Associations • • • • Setup Route Node Info Log Status Bar 3.4.1 Main Menu On top of the Main window is the Application Main Menu.
UZB3 Z-Wave USB Adapter 1 1 Help menu Z-Wave Pc Controller comes with its own built-in Help system. The Help menu includes the items to access this Help system. Menu item Keyboard Shortcut Index Contents Description Browses Help system by keywords. F1 Browses Help system by topics. Search Opens search tab of the Help system. About… Displays the version and short status information of the application All information are correct at the time of release.
UZB3 Z-Wave USB Adapter 1 1 3.4.2 Node View The Node View contains Menu Bar, Node List and Node information for the selected node. It is used for operations with nodes. Figure 6. Node section All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2014 Sigma Designs, Inc.
UZB3 Z-Wave USB Adapter 1 1 The Node’s Menu Bar has the following items: Menu item Description NW Inclusion Network Wide Inclusion, to include all nodes into network once they have been reset and given power Add To Add a node Remove To Remove a node Node Info To request Node info from a node Request Node Neighbor Update To get the neighbors from the specified node.
UZB3 Z-Wave USB Adapter 1 1 The Node List has three columns: • Node Id – shows the IDs of all nodes in the network; • Device Type – shows description of the type of every node in the network; • Status – shows the current status of a node. The Node Info section gives structured information about the selected node. For more information, please refer to Z-Wave Device Class Specification documentation. All information are correct at the time of release.
UZB3 Z-Wave USB Adapter 1 1 3.4.3 Controller View The Controller view includes Menu Bar, Network Role Option and Controller Information sections. The Controller view is used for operations with controllers. Figure 7. Controller view The Controller’s Menu Bar has the following items: All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document.
UZB3 Z-Wave USB Adapter 1 1 Menu item Description Start Learn Mode Starts learn mode for the controller if it is needed to include it in another controller’s network Reset Resets a controller Create New Primary A SUC can create a new Primary Controller in the network if the existing Primary controller fails Request Update An Inclusion controller can request network updates from a SUC or a SIS Shift Is used to shift primary role to another controller in the network Load Command Classes from dev
UZB3 Z-Wave USB Adapter 1 1 3.4.4 Associations View The Associations view has a Menu bar, and two fields: Source and Groups. It is used to set up associations between nodes. The Menu bar has two items: Menu item Description Create Association Creates an association between selected nodes Remove Association Removes selected association The Source field shows the list of available source nodes that support the Association command class, e.g. Binary sensor.
UZB3 Z-Wave USB Adapter 1 1 3.4.5 Command Class View The Command Class view is used to send a specified command class to a selected node. It has the following items: • Command Classes: drop-down list to select a command class; • Command Name: drop-down list to select a command name belonging to the selected class; • Command Parameters Grid: to enter command parameters. Figure 9. Command Class view All information are correct at the time of release.
UZB3 Z-Wave USB Adapter 1 1 3.4.6 Setup Route View The Setup Route view has a Menu Bar, Source Node list and Destination Node list. It is used to set up routes between nodes. The Menu Bar has two items: Menu item Description Assign To assign routes via nodes Delete To delete assigned routes Figure 10. Setup Route view Source Node list and Destination Node list show the lists of source and destination nodes in a routed network respectively. All information are correct at the time of release.
UZB3 Z-Wave USB Adapter 1 3.4.7 1 ERTT Z-Wave PC Controller has the Enhanced Reliability Test Tool implemented. It can be activated as a tab through the Categories menu or through Ctrl+E keyboard shortcut. Figure 11. ERTT All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2014 Sigma Designs, Inc.
UZB3 Z-Wave USB Adapter 1 3.4.8 1 Log View Here output of current actions is recorded. The two tabs, Actions and Packets, show full information about what is happening within the PC Controller. Figure 12. Log View All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2014 Sigma Designs, Inc.
UZB3 Z-Wave USB Adapter 1 3.4.9 1 Log View Status Bar displays Home ID, controller node ID and Command queue status. Figure 13. Status Bar All information are correct at the time of release. Sigma Designs owns the proprietary rights to the information contained herein this document. It may not be edited, copied or circulated without prior written agreement by Sigma Designs. © 2014 Sigma Designs, Inc.
UZB3 Z-Wave USB Adapter 1 1 4. FCC NOTICE TO USERS Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
UZB3 Z-Wave USB Adapter 1 1 5. EU DECLARATION OF CONFORMITY EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
UZB3 Z-Wave USB Adapter 1 1 Česky [Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
UZB3 Z-Wave USB Adapter 1 1 Nederlands [Dutch] Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti [Maltese] Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma malħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar [Hungarian] Alulírott, [gyártó neve] nyilatkozom, hogy a [...
