KS-6001 Sub-mixer Operating manual L PF L C R L PF L C R L PF L C R FD LINK 200 200 A-B P-48 Dy-M LINE +4 -30 -20 -70 P-48 PF L C R 20 0 A-B A-B PEAK L FD LINK Dy-M LINE PEAK +4 -30 -20 -70 P-48 Dy-M LINE PEAK +4 -30 -20 -70 20 0 A-B P-48 Dy-M LINE PEAK +4 -30 -20 -70 POWER
KS-6001 Introduction Thank you for your purchase of the Kamesan KS - 6001. This sub audio mixer provides a flexible and powerful solution to your portable mixing needs, accepting up to four balanced microphone inputs, and mixing them into two before passing them to another mixer via a dedicated hardware connector integrated into the case design, or through a separate cable. Power is supplied from an outside source, either through the mating connector or a dedicated DC inlet.
KS-6001 exceptionally cold environment, battery service life may be shortened, and there may be a drop in performance. If at all possible, use this unit in the temperature range as indicated in the specifications. When connecting this unit to external devices, be sure to read all related operation manuals and connect the devices correctly to each other. If there are mistakes in the connections, it is possible that either the KS - 6001 or the other unit(s) will be damaged.
KS-6001 Attaching the KS-6001 as a sub mixer Locking pins (bottom) and sockets (top) These locking pins and sockets locate the KS - 6001 in position when connecting it to another unit. They are secured and released with the locking levers Multipurpose connector This multipurpose connector carries signals to and from the KS - 6001 to the other unit. It is usually recessed, but may be released by sliding the small silver lever (marked RELEASE) using a small screwdriver or similar.
KS-6001 ������ ������� ������� Side view of KS-342 with KS-6001 fitted, in case with cushion (gray) Carrying the unit In situations such as news reporting where the unit is to be carried during use, we recommend that the KS 342 carrying case be used. It can be attached to your belt on the carrying case and used together with the KS -342. If the unit is used with any other type of carrying case, make sure that all units are firmly affixed in the appropriate speciallydesigned carrying case.
KS-6001 Parts of the KS-6001 Since the operation of the KS - 6001, once it has been fitted as a sub-mixer, is a relatively simple matter, this section contains the information you need to get up and running with the unit in most cases. Later sections contain more detailed information covering special circumstances. Side view Power switch Side locking lever 7 POWER 1 6 2 5 3 BUS MIX AUX (MONI) OFF Mix switch External power input MIX OUT (-20dBs) 4 CN Pin Assign 1.FG 2.Lch H 3.Lch C 4.Rch H 5.
KS-6001 Side view The four XLR male connectors are used to connect appropriate microphones (or line-level sources) to the unit. Always ensure that microphones or line sources are correctly selected using the front panel selection switch, in order to avoid possible damage to the sources or to the KS - 6001. The XLR connectors are wired in the standard 1=ground, 2=hot, 3=cold configuration.
KS-6001 but in this case, the level and left VU meter indication (on the KS -342) will be lower than the actual values. Channel fader Turn clockwise to increase, and counterclockwise to decrease, the output level of this channel. Output bus assignment Use this to send the output of the channel to the left (L), right (R) or center (C – left and right) output busses.
KS-6001 If this (and/or the equivalent indicator on the KS -342) flashes read, you should immediately replace the batteries. Using the unit—some notes Before starting to use the KS - 6001, or connecting any equipment to it, make sure that the unit’s power switch is turned OFF. Before actually connecting microphones or other sources to it, make sure that the input selector switch is turned to the appro priate position for each channel.
KS-6001 Technical notes and specifications, etc. Inputs Input level (4 channels) Input impedance MIC – 70 to –30 dBs (balanced inputs) LINE –20 to +4 dBm (balanced inputs) MIX 1.
KS-6001 Electrical characteristics Figures measured when connected to KS -342 External power supply Between +10 V and +16 V DC (maximum power 0.
CH4 INPUT CH3 INPUT CH2 INPUT CH1 INPUT (XLR-3) (XLR-3) (XLR-3) (XLR-3) A-B 12 LINE P-48 Dy-M A-B 12 LINE P-48 Dy-M 13 A-B 12 LINE P-48 Dy-M INPUT SEL. P INPUT SEL. P GAIN HA MIC -70~-30 LINE -20~+4 H.P.F. ( 20~200Hz ) MIC -70~-30 LINE -20~+4 H.P.F. ( 20~200Hz ) MIC -70~-30 LINE -20~+4 H.P.F. ( 20~200Hz ) MIC -70~-30 LINE -20~+4 H.P.F. ( 20~200Hz ) POWER GAIN Peak GAIN Peak HA LINE A-B 12 GAIN Peak HA Peak HA P-48 Dy-M INPUT SEL. P INPUT SEL.
KS-6001 About Kamesan Sigma Systems Engineering was started in 1972 to develop and design professional mixers for studio and remote broadcast applications. Today, following the “slow and steady” principle of the tortoise, we have built up our sales and our reputation to the extent that we now enjoy 95% of the Japanese portable mixer market.
Sigma Systems Engineering Co. Ltd. 3-5-2 Okubo Shinjuku-ku Tokyo 169- 0072 JAPAN Tel: +81 3 3204 2611 Fax: +81 3 3204 2250 e-mail: sales@kamesan.co.
