Specifications

Figure 3-5. Rear View of SS2000SM.
-6-
Figure 3-6. Amplifier Unit Power Cable and
Fuse Clip Adapter Installation.Figure 3-4. Control Head and Bracket Installation.
Figure 3-3. Control Head Bracket Assembly.
speaker leads marked “2” to the SPEAKER HI
POWER or SPEAKER LO POWER power cable
leads. See figure 3-6.
Using 18 gauge wire, connect the
speaker leads (58W speakers to SPEAKER LO
POWER or 100W speakers to SPEAKER HI POWER)
as shown in Power Cable Wiring Diagram, figure 3-6.
2. Radio.
To allow incoming radio messages to
be rebroadcast over the outside speakers, connect the
two brown zip cord leads (pins 9 and 12 of the power
cable) across the two-way radio’s speaker.
3. Horn Ring.
In order to utilize the horn ring control
of siren tones (Tap II) and other features of the siren,
the following procedure must be performed.
C. Drill two mounting holes at the position
marks.
D. Secure the mounting bracket to the mount-
ing surface with the #10 thread-forming screws as
shown in figure 3-4.
3-6. ELECTRICAL INSTALLATION.
A. Power Cable Connections.
The power cable included in the carton is
equipped with a twelve-pin plug that mates with the
connector on the rear of the Amplifier Unit (see
figure 3-5). The cable is supplied with a 20-ampere
in-line fuse. Additional wire (the same gauge or
heavier) may be spliced to the leads as required. The
various wires on the connector must be connected as
follows:
1. Speaker.
The unit is designed to operate with
one 11-ohm impedance speaker or two 11-ohm
impedance, low power (58W) or high power (100W),
speakers connected in parallel and in phase. On
Federal speakers, this can be accomplished by
connecting the two speaker leads marked “1” to the
SPEAKER COMMON power cable lead and the two
290A4023-04
CONTROL HEAD
BRACKET (1 OF 2)
NOTE: USE ONE OF THE THREE
SETS OF HOLES. THIS ALLOWS
UP/DOWN CONTROL POSITION OF
THE PIVOT BRACKET.
#6-32 x 1/4" SCREW,
PHL. PAN HD (2)
PEM-NUT (ATTACHED
TO BRACKET)
#6 SPLIT LOCKWASHER (2)
290A4023-05
PILOT HOLES (2)
MOUNTING HOLES
FOR #10 SCREWS
PREVIOUSLY ASSEMBLED
CONTROL HEAD
AND BRACKET
PEM-NUTS (ATTACHED TO BRACKETS)
1/4" LOCKWASHER,
EXT. TOOTH (2)
BRACKET (2 OF 2)
MOUNTING
SURFACE
#10 SCREWS,
THD. FORM. (2)
1/4-20 x 3/4" SCREW,
HEX HD. (2)
290A4023-07B
BLU
SPEAKER, COMMON
SPEAKER, LOW POWER(58W)
SPEAKER, HIGH POWER(100W)
(NEG.) (-) AT FUSIBLE LINK
(POS.) (+) FUSE BLOCK
HORN RING
HORN
PURSUIT OR PARK DEACTIVATOR
ORN
BRN
BLK
RED
20 AMP
PRP
BRN
BRN
GRA
WHT
WHT/YEL
COMMON MIC. / EXTERNAL RELAY
VEHICLE TWO-WAY
RADIO SPEAKER
123
456
789
10 11 12
290A4023-0
8
1. SLIP MALE
CLIP OVER THE
FUSE.
2. INSERT CLIP
AND FUSE INTO
FUSE BLOCK.
3. ATTACH THE
RED WIRE WITH
FEMALE CLIP.
MALE
CLIP
FEMALE
CLIP
RED
WIRE
FUSE
TOP OF
FUSE BLOCK
LIGHTS AUX OUTPUTS NO NC C
3
SignalMaster
FUSE
+ BAT
21 ABCDE
SignalMaster
TM
FEDERAL SIGNAL CORP.
SS2000SM
S
I
R
E
N
MIC
KEYPAD
INPUT
SmartSiren SM
R
UNIVERSITY PARK, IL USA
290A4023-06
B
12 PIN CONNECTOR TB1 J2TB2
U.S PATENTS 5,296,840 OTHER PAT'S PENDING